How to Adjust the Turret Stop on a DeWalt DW735 Planer

DirtFarmerJay
310 followers
73 Video Views·Oct 26, 2024
hey dir farmer J here from dirtfarmer
j.com we love having this
dw735 planer it's been a great addition
and one of the features is the turret
that allows you to preset thicknesses on
it but how do you know if the turret's
correct hey we'll show you how to
calibrate
[Music]
it hey dir farmer J from dir farmer
j.com we love the features that we found
on our DeWalt dw735 planer and we've
upgr gred it with several things here
that we'll point out as we go but what
we're going to focus on today is this
great little feature called the turret
what this allows you to do is to set the
finished thickness of stock you're going
to run and as you can see there's a
range of them here uh starting at an e
in for thinness up to qu/ inch
3/4 1 in and 1 and 1/4 in if I raise
this a little bit more so that it can
cut down to that
so those are presets but if there's a
change out like what we did we put in
the shelix um segmented head uh in this
unit and by the way if you want to see
that installation of the review just
check out the links that are showing
above uh or in the description below but
we put in the shelix head it was just
very slightly a different diameter
cutting Arc than what came with the
factory 3 knife installed heads that was
here um and so by doing that we had to
calibrate a couple things one is
whatever comes out of here that you cut
that is the finished thickness and you
need to adjust everything else so
whether it is a visual site reading
gauge or you put on a digital gauge like
this wixie and if you want to see how to
calibrate that wixie and install that
look for those links below down in the
description as well or the links show up
above now once we've got these two
talking to each other now we need to
make sure that this is lined up and as
you could see when we put this all
together crank this down and we're just
going to set it to the 1 in uh thickness
that we want when we cranked it down to
that final thickness and say okay I'm
hoping to produce one in stock and you
just let it bump it you don't crank hard
when it hits that if I go back and check
out the readout over here on the wixie
digital readout it's telling me no
you're actually producing stock a little
bit thicker uh it's showing
1.03 which is 1 in and a 302 so this now
needs to be adjusted so that when we
bring this down and bump against it it
says one this says one everything is
ready to go let me show you how easy
that is to do the first thing we need to
do is raise the cutter head uh and that
means reversing the handle back like
this I kind of um remember this kind of
like as a pilot if you're finding a
stick aircraft if you push down or
forward the plane's going to go down if
you pull back it's going to climb so
we're climbing this up out of the way to
give it some clearance and now you can
see over here uh the rod that is the
stop rod plus the adjustment nut on it
well right now it's reading too high so
what that means we're just it's going to
take a/ in or about 12 mm wrench we're
going to put it on the nut here and just
slightly loosen that just a little bit
and now I can take this rod and I'm
going to just turn it and shorten it
just a little bit and just a little bit
of trial and error I'm going to go ahead
and set that like this now I'm going to
turn this back on over
here and go ahead and descend the cutter
head until it bumps the top of the
turret rod
and let's just see what we get we got oh
about a/4 inch more to go let's see if I
hit it no I'm still thick uh not me
personally but the wood that's coming
out of here okay so uh I still need to
lower the rod a bit so I'm going to
raise this a little bit more go back
over open
this give it a little bit more of a turn
down
and go ahead and tighten
this now you don't have to tighten it
too hard and you might leave it loose
but I kind of like it to be home where
it needs to be okay I'm going to I'm
watching my gauge over here as I come
down let's
see we hit it so we're at
1.0 right now so now this is calibrated
to the readout which is calibrated to
the output of the planer so everything's
in syn here it's a beautiful thing and
for those of you that have a band saw in
your maker space you know how incredibly
valuable it is well check out this
episode where we show you six great
upgrades inexpensive highly effective
will get more use out of your band saw
you'll love it and while you're at it
check out this other video from our
catalog that YouTube thinks is perfect
for your interest and we'd love it if
you watch it too until the next time
this is dirtfarmer J from dirtfarmer
j.com
[Music]
