Common Mistakes Part 2

Snow Sledding
37 followers
5 Video Views·Oct 20, 2024
This week Dan talks through so of the most common mistakes he see's riders making.
What's up guys? Welcome back to the Next Level channel. Happy Monday. Hope you guys are having
a good one. Today we're going to talk about common mistakes, and it's common mistakes 2.0. It's about
halfway through the season. I've done a ton of riding clinics, so I've been around a lot of
people and seeing a lot of things continually happening. So we're going to talk about some
more common mistakes. Let's get into it. All right, everybody. So our a year ago common
mistakes video, maybe it's even been two. Clark, was it last season or the season before that we
did that? It was a while ago. The common mistakes video was easily the most viewed video and had the
most comments connected to it, and I think it was because it resonated with so many dang people.
Well, those were all essentially riding tip common mistakes, and this year not only am I seeing
riding mistakes, but I'm also seeing stuff, you know, even before we get riding. So we're going
to go over some other common mistakes in common mistakes 2.0. In terms of what we're doing to the
snowmobile, you guys have seen plenty of videos of myself and other guys are out there, you know,
adding a bunch of stuff to the sled, and there is a lot of that where there's a lot of expense to
that. Some of the common mistakes that I'm seeing, there's no expense to any of it, and what's funny
is that without doing these things and remedying these common mistakes, they could end up costing
you a lot of money. Awesome. So one mistake, we're going to just start this off with a mistake that I
see that is free, and it's just easily something that if I have the right tools and I kind of know
what I'm doing, we can set the sled up so that it's going to work better for me, and the first part of
that is handlebars. I see all too often people riding the sled with their throttle way up in
the air or way too low, or maybe even worse, it's super loose and it's kind of all over the place.
I also see people that when I stand up on their sled, I see the way their brake is set up, and
you know, they don't have the brake adjusted properly, and every bit of this, if we got the
right tools, we can adjust the brake and the throttle and literally everything onto our
handlebars and sort of make it personal to us. So where should the brake be? So as I stand on the
snowmobile, having the brake to where my wrist, as my wrist and my arm, my forearm comes down,
it's nice that I have my, the angle of the brake set to where I'm not up like this, I don't need
to be super low like this, but just in a comfortable position to where this is a position of comfort,
not only that, it's a position of power. So I've got this like this, if I'm standing up and riding,
this feels nice on my arm, I'm not having to tweak my wrist in any way, and on the throttle side,
it's very similar. I run my throttle nearly level, maybe just a little bit down, and I like
having it that way. I feel like as a stand-up rider, I can get good hold on the throttle,
and then I've also got that ability, if I needed to, to ever come underneath, and I'm not doing
that a lot, but I don't want to throttle so out of whack or out of position, nor do I need this
thing so dang tight that I can't make little adjustments to it. The other reason that I will
leave this throttle block somewhat adjustable is if I ever impacted it. If I ever came into it,
the likelihood of it, you know, moving versus braking or even going into me is a lot better
with it just a slight bit loose right there. And then obviously we've got the tools to adjust that
if that becomes a bit too loose or too tight. So having the right tools, and this is a situation
with with my controls that I get it, a lot of you could just get this set up in your garage,
in your shop, and it's kind of set up, and you already know about it, and you don't need to bring
those tools, but remember that there is a lot of times when these things change or maybe need to
be changed when I'm out on the hill, so I don't mind having the right tools to make these adjustments
with me in the backcountry. All right, so having some various Allens, there'll be an Allen in
here specific for right underneath the throttle block, a Torx set, having the right Torx to go
and make these adjustments so that I can move that brake. Not only am I thinking about the
brake in terms of its angle, I'm also wanting that brake lever to be right where it's very
comfortable for me to either use my middle finger or my index finger, and a lot of times the way
they're set up is the brake is pulled all the way over next to the grip, and people are wondering
why. Well, it's either very difficult for them to get to the brake, and then they will choose to not
ride with one finger on the brake because it's so difficult to get to. We can adjust that, so we take
a Phillips head screwdriver, we move over the brake, sorry, the reverse button, we use a Torx
head, and we can slide this over, and while we're adjusting for that angle, we're also sliding that
over, making it a lot easier for me to get my one finger on the brake. So another common mistake,
and remember guys that these aren't these like life or death things, right? These are just things
that are going to help better improve our day of riding, and again, having the right tools for the
job is going to make this quick and easy. I think that there are a ton of videos that are out there
about track tension. Well, when your track ratchets on you, right, when it's so loose that as you're
riding, and it's funny that track tensioning, and when it happens, it's usually when you're having
this awesome time, and you were just so wishing that you made it to the top of the hill, and all
of a sudden you heard your track ratchet, remember that's that center cog literally being so loose
because the track has loosened up, where it's starting to spin, and you're hearing that ratcheting
sound. Having the right tools to improve track tension, pretty simple, and again, having those
tools while you're out there can make that ride that much better. So we'll need a 16 millimeter
wrench. I like having the option of having an open end, as well as the box, right, or the closed end,
as well as kind of the same deal with a 10 millimeter. So the 16 way Polaris designed that
is pretty nice. I need two separate wrenches to make this happen. So the 16 millimeter, you'll
come right to here on this side. We'll call this the clutch side of the snowmobile. You're going
to just break this one bolt through all the way through there. That thing will just relieve the
tension to the idler wheels, and then you'll take your 10 millimeter as well as this same wrench,
and as you come in through here, you've got to pop that jam nut loose with your 16 millimeter.
So you'll open that up, get this where this is going to move back and forth here with, obviously,
if we're trying to create some track tension, we want it to move back. Now when you're in the field,
there is some science behind it, but really what you're trying to do is as I'm going to go in,
right, I'm going to tighten because I'm trying to tighten the track tension. I want to come up with
a way that as I loosen up the jam nut and I'm running that 10 millimeter, what we often like
to do is I will run this 10 millimeter up like this to where it's touching the track. So I'll
this as close up here as I can, and as I start to tighten, I am just doing equidistant turns,
and I'll count those turns, and typically I'll do something like five turns. So if I'm kind of
looking at the bottom of the track and I'm trying to tension, I'm doing from the bottom of the track
up to where I'm touching again, and I'll do that maybe five, seven times, something like that,
just depending on how loose I really feel like the track is. Do the same thing on the other side,
use that 16 millimeter box in, tighten up the jam nuts, and then obviously remember to come
back here to this rear axle and tighten it up, and it's not a perfect science. Really what we're
trying to do is we want track tension to be there, but we don't want it so tight that it feels like
it's laboring the motor or slowing it down, and you'll know when you let off the gas if it feels
like you've more or less got like an exhaust brake on your sled. Well, a lot of that can be
attributed to having a track that is just too tight. We'd want our track tension to be nearly
as loose as it can be without ratcheting, and so remember that we're going to do things and sort of,
we're going to just start in small increments and then work up to it. You may not be able to get
your track tension dialed on the very first one, but I would start with that five to seven turns
somewhere in there. That's been good luck for us so far. So the toolkit I have in my guide sled
and I've got tools kind of spread out all over the place, but I just wanted to make reference that
this isn't a complete kit, not in any way shape or form. I've got some tools that are kind of specific
to the video. There are quite a bit of tools that are specific to a lot of the things on the
snowmobile, but some of the key things in terms of the mistakes that we're seeing is having the right
tools necessary to do some track tensioning, and the next one would be, and you guys have seen
plenty of videos about proper belt deflection, time and time again I'm opening up a customer sled
and seeing belt deflection where it's just either way too tight or even worse where it's just way
too loose and we are robbing ourselves of horsepower. So the next one and a common
mistake will be belt deflection. All right, so again, common mistake is always, always checking
belt deflection. So every morning we get into the side panel and most of the time we're checking on
our engine oil, making sure I've still got a belt in the belt caddy, maybe some spare plugs,
and all of it just depending on, you know, the ride from the, the ride from the day before or
whatever it looks like, but we're repeatedly checking oil of our engine and then a lot of
times I think I see people just doing this number where they kind of just look there,
everything looks normal, and I'm going to just go ride. Let's remember that kind of inspecting the
belt and taking a peek at it, it's a great way to start the day, man. If the day is to go out there
and squeeze the throttle and go have a blast, I want to make sure before I leave the comfort of my
shop that all of this stuff is looking right. I don't have any hairs or imperfections on the belt,
you know, this belt's probably got six, seven hundred miles on it, so there's definitely some
signs of some glazing, you know, and it's wearing out. I think Polaris would recommend,
you know, about every 500 miles just depending on the type of rotting that you're doing, but,
you know, it's a wear item, so it'd be something that we'd want to inspect, but to inspect that
and then look at the belt deflection, you guys have seen plenty of videos on this to where
I want to be able to roll this belt back, which right now my belt deflection is set really,
really good. I'm able to move that back between the shivs of both clutches, but it's taken some
effort to do so, and that's a great way to just test that that belt deflection is right.
When it's too tight, you'll start the sled, the sled will not only idle down, but in some
situations it'll start to squeal, and then I'm sure we've all seen where the sled literally
wants to kind of go forward on us, and that would be an example of belt deflection set way too tight.
All right, to adjust our belt deflection, I need my 11 millimeter as well as my eighth inch Allen,
and notice with the tools guys, I've got an 11, I've got a wrench that's just an 11 and a 10.
That's a great like sort of space and weight saving setup, because there are a lot of situations where
I need a 10 millimeter as well, but for belt deflection, the 11 as well as the 8, you guys
have seen plenty of videos on belt deflection. I'll use this jam nut here, I use the eighth inch
Allen there to get that thing set. Remember that as I loosen that up, you got to kind of think in
opposites. As I am tightening, as I am turning that Allen in before I set my jam nut, I am opening
the shivs up, right? As I open that up, when that belt is sitting in there, that can make the
difference of whether it was too too loose or too tight. Again, if I am loosening it, if I'm pulling
it out, I'm actually taking that and tightening, bringing those shivs in. So if I were wanting to
tighten up belt deflection, I would be opening those, I would be loosening this and allowing
these things to close to get around the belt. So there are so many videos out there about proper
belt deflection, it's just having the proper tools and this doesn't always happen when you're at the
shop. This may happen while you're out in the field and or if you had to change a belt. If you
got a belt that's got six, seven hundred miles on it versus a brand new belt, the way this clutch
is adjusted, well it's adjusted and has been adjusted for this belt that's got a lot of
miles on it. You put a brand new one on, chances are belt deflection will be out and you'll need
to adjust it. Once we know, and remember it's not a perfect science, but once we have an idea
that our belt deflection is set right, the clutch pan or the side panel is already off,
I've got clear view of my clutch. And I'd also like to point out that anytime I'm near or around
the clutch, I would want to remember that my kill switch and or my key, and good practice is to have
both of them, are turned off or the kill switch is down. Anytime I'm rotating this clutch, remember
that you know we can primary start our machines, obviously rotating one direction. Let's not lose
any fingers while we're doing this. So as I'm inspecting the primary, it's always a good idea
and we're always talking about cleaning clutches and all of that stuff. Remember that they're high
performance machines, we want them to run better than our buddies. So I'm always inspecting not
just the overall condition of the primary, but I'm also looking down in there looking at the primary
spring. Oftentimes everybody, that primary spring can either be sacked out, like really fatigued,
right? Let's remember what it's doing is like at RPM, that thing is just constantly opening and
closing, opening and closing. That thing over time can sack out, you know, every few hundred miles,
that thing's probably gone through a ton of in and out motion like this and can get fatigued.
I've often had them and had one already this year where they break. And when they break, most of the
time you can see it, but sometimes you can't. So if you had a situation where you were riding and
you had sort of a rapid loss in RPM or the sled just didn't feel right, it didn't idle the same,
whatever it looked like, this would be one of the first places I would go and just take a peek in
there and make sure that that spring was in good working condition. Carrying a spare primary spring,
man, if you've already made the 20-something hour trip out west and you were riding on a Sunday
and you broke a primary spring, I mean, that's 22 bucks that could make or break your Sunday.
And if you didn't have one as a spare and nobody else is open, what a bummer way to close out your
day. Can you still get out with a broken spring? And the answer is sure, but man, we don't have
any more performance just based on that primary spring. All right, within the last week of riding,
I've had quite a few people reaching out to me about frozen throttles. And so part of today,
once we get into snow, we're going to be talking about, once the sled rolls over,
the importance of blipping that throttle and getting that snow and ice and debris in and
away from that. But let's remember this, because I just had this happen. A guy came in and said,
man, my throttle, I gave it gas, the throttle cable stuck, and the flipper actually came off
the cable. And if he wasn't wearing a tether, well, there went his snowmobile. And he was claiming
that there was ice bound up inside the throttle cable. I came out to a snowmobile and right
underneath here, guys, where you take this Allen and you come up underneath here to adjust the
tension on that throttle block. Let's remember that this throttle block sleeve that's underneath
there, if that takes an impact, a lot of times I've seen those, because it's happened to me,
where they'll actually bounce out of that groove from underneath there. And when that happens,
suddenly the throttle gets super loose. And then what a lot of people will do is be like,
wow, I don't know why my throttle block came loose, but I'm going to just grab this Allen
and go retighten that sucker back up. When you do that, that will oftentimes be the reason why
you'll go give it gas. And because it's pinched in there, that's what will happen. And that
throttle will stay wide open. So another reason why we're not leaving home without these.
So that's just a trick for everybody that keeps thinking that their throttle might be bound up
with snow and ice. It might've actually popped out of that sleeve from underneath,
which then it's going to take not only an Allen, but a Phillips head screwdriver,
get rid of those four screws that are here, pull this cap off. And you actually have to work that
sleeve back out of the throttle block from underneath and then put it back in, tighten
everything back up. And then you've got throttle again. All right. Lastly, guys, as we're kind of
rounding out some of these maintenance mistakes that I'm seeing and talking about some tools,
you don't need the entire freaking toolbox, but you need some of this stuff. Remember that as I
look around the snowmobile, there are things about a sled that it'd be one of those things
where I'm like, man, I'm so glad that I checked it because it was loose or I didn't check it.
And I cannot believe I lost a bolt and it fell out. It's usually happening when you're way back
there. So don't be afraid as you're kind of getting through the sled and you're, you're
getting through your season. And even though you've got X amount of miles on the sled,
know that it's good practice to just go through, take a 13, a 15, a 17. And I get it. I'm talking
a lot of stuff that's Polaris or even access chassis specific, but there's so much of this that
plays a role to no matter what manufacturer sled you're using. So if there are different
wrenches for those particular situations, you know, make sure that you're carrying the right
stuff, but a 13 on the low suspension, a 15, a 17, even something as simple as, you know, halfway
through your season, check in the wear and tear of your ski rubbers. You know, guys that go out
there and they have a damaged ski rubber. And again, it's a Sunday and your ski rubber fails
riding without a ski rubber. Uh, those that have, that have tried it and I've tried it as well
is an Epic fail. And again, that's a $10 part or go to a Dura pro, which is a lot more expensive.
Chances are, you're not going to see the failures with those, but it happens, right? And so being
able to inspect some of that stuff prior to your ride. I mean, those are some mistakes that I
All right. You guys are noticing that there's a lot of common mistakes that are happening,
not on the snow. We're just, before we even leave the shop, the trailhead, the trailer,
the truck, whatever it looks like. Another common mistake that I see people doing is going out with
either no radio, which is a complete mistake. As a backcountry rider, you guys know just how
quickly our group, especially if we're riding with a large group can just get scattered. It's
like herding cats, especially on a powder day, everybody just sees the snow. And next thing you
know, we're in the trees and nobody knows where anybody is having radio communication just to
keep the group together, right? Let alone a first aid or an avalanche situation. We such an ideal
tool to have. So as we talk about the, the basic backcountry, you know, the equipment, the stuff
that we need, we need a beacon probe, shovel, backpack, and then the radio. So having the radio,
making sure that it's charged, you guys have seen the oxbow stuff that I've been running.
The radio itself is super loud. It's very easy to change the channels. Let's remember on the
oxbow channel or on the oxbow radio, I need to push and hold the function button and you'll hear
this thing there. That's now padlocked. So as I put this thing up and I get ready to ride, that
thing is ready to go. And I'm not going to reach up here as I key the mic and change channels and
all of those other things. On the BCAs, still nothing wrong with a BCA radio, but the trick to
that is again, making sure that it's charged. And the other part of that too, is when we forget
and we leave these things on, you know, you'll key the mic and hear that beeping and it'll actually
show red on the mic. Your battery's not working. Well, a not working radio is just like a not
working transceiver or not working backpack. Do people still go ride? And the answer is yes.
Should they, and should they be responsible? And the answer is, well, when it's a pow day,
seems like people just, what we're willing to go out there and risk when we don't have this
stuff working properly. Oftentimes I see people with the BCA, because this is now in the backpack
or stowed elsewhere. They've got this thing up on their backpack position somewhere and halfway
through the day, they're hearing everybody just fine. Batteries charged. And then suddenly they're
not. Let's remember that oftentimes guys will, they'll either get in between a channel. So they
thought that they were on channel a and now they're kind of stuck here or even worse. They
start switching channels and you guys will hear that thing beeping. And a good tip is whatever
channel you've set your, your radio up to with you and your group, go ahead and preset your channel,
a your channel B and your channel C to the exact same channel. That way, if you do decide to switch
channels on yourself, you're still connected with your group. Oftentimes I see people, man,
I've been calling for you forever and you look up and you're like, yeah, it's because you're on the
wrong channel. So that's a great tip with the BCAs and with any one of the radios guys, just
making sure that they are fully charged and you're ready for your day riding. All right. So another
common mistake is people foregoing the trailhead check and solely relying on a beacon check station.
Are beacon check stations good? And the answer is absolutely. I love the fact that there are
so many trailheads now that are putting these, these check stations up. Let's remember as we
go by the check station, transceiver is, as I stow it away, it's sending out a signal. So as I go
by there, the check station is just always in search. So it is picking up that I am sending
a signal and it's giving me either I'm not set up properly, that LED X reminding me that something's
wrong with my transceiver, or it's not even turned on. So it's giving me that X when everything's
working properly, it's giving you that green circle saying, yes, it is picking you up in send.
A trailhead check, something unique and uniquely different, and not something that we should miss
or forego. You get your group together and we form a wheel. I am the hub, right? The center of the
wheel, everybody to the outside. And since I don't have a group with me, we're just going to use some
open transceivers. These guys have all turned transceivers on check battery life. My battery
life was 79 today. We're going to remember that somewhere between that 60 and 70% is we're going
to want to swap out those batteries. We want great alkaline batteries, full charge. These are
life-saving tools, and we don't want to mess around with a, well, with low charge somewhere
below that 60 and 70. So each one of these in your group, you'll let everyone know that's on the
outside of the wheel to go into search mode. So I'm going to quickly go around and put these into
search. That's in search, search, search, and you can go into search as well. Okay, you're in search
mode, Steven? Yeah. I'm coming towards you, and you are making sure that you're picking me up,
and you can see that you are. That making sense? I go around to each person. I can hear those
numbers changing. I can see those numbers doing their thing. That one's working. Same thing here.
Go ahead and put your transceiver back in send. There you go. I'm going to do the same with all
of these guys, just like this, like that, just like that. So I would ask your group in this trailhead
check, everybody go back into send and stow them, so just like they're going riding. Now I'm the
only one left with a transceiver out. We've already shown to everybody in the riding group that they
can pick me up in send. Now I go to search, verbal confirmation that I'm in search. Guys, I'm in search.
Now I'm picking you up because your transceiver is now inside where you've stowed it. You can see
I'm picking you up. I'm doing the same thing all the way around, making sure each one of these guys
is now sending a signal properly. There they go. Last one. There it is. So now I've checked my whole
group, and now I'll come up to the last person in the group. I'm going to go back into send,
making sure that that's now sending a signal, and go ahead and stow my transceiver. We do that,
and we do it in that sequence to reduce the variables. You can tell that if we did it the
other way, all of a sudden now the three or four people that are in my group could have very easily
put their transceiver away and had something change as they put it away. Now everybody can
be confident that we have both checked our transceivers in send as well as in search.
Then I go by the beacon check station. I should be getting the green zero. If something has changed
between now and that time, that's one more reason that we would check it. But a common mistake I see
people doing is failing or foregoing the trailhead check. What happened? All right,
the next common mistake. It's been happening so much, especially in the last few weeks. We've had
a ton of good snow, a lot of deep snow. You guys noticed on the way up, instead of staying neutral,
feet back, body forward, just like we talked about in the common mistakes video from earlier,
I'm coming up the hill, and I feel like I'm going to be such an anticipated rider,
but I'm going to get to this uphill side early. You guys noticed that it didn't matter coming up
the hill where I was looking. I'm like looking the direction I want to go, but my body weight,
my body weight being on this uphill side while the sled is still going up.
Well, with my body weight on this side, what am I telling the sled to do? Go up. And so I'm leaning.
I've got my chest forward. I'm looking this direction, but because I've put all that center
mass to that uphill side, here I sit. And this has been such a common mistake throughout the season,
by far one of my number ones. So the remedy, up the hill, neutral position. We're going to build
momentum coming up the hill. I've got to wait. I've got to wait until I can give that sled
direction, get committed to either a right side or left side side hill. Once that sled is doing
thing, then I make that transition, get uphill side, set the sled and boom, side hilling 101.
Yeah. All right. So significant changes may not seem like it, but built a lot of momentum,
maintain that momentum from where I can get it. All too often I see riders going slower than
molasses on the flats. As soon as they hit the hill, it's just like this wide open throttle
trench lean back. I have no steering. I built that momentum right as I got to that hill,
as fast as I can go maintain that momentum up on the hill. I have so much momentum and so much time.
I'll start to turn that sled in the direction that I want to start my side hill. And I've got time to
make that transition off the gas, get my foot over here, opposite foot forward, get a bit forward on
the sled and then flipping that throttle, setting that sled into the side hill. Now I've taken the
steepness out of the hill. So the mistake, the common one is I get over too early, right? We
continually talk about not being a reactive rider, but being an anticipated one that position and
jumping over there too early as we're anticipating being on this side of the sled, but there's timing
involved. So we're doing it too early. So hopefully this kind of describes what is happening there.
And those of you that are struggling with that, remember that you've got to stay neutral,
get committed to that direction, then put yourself into this spot.
You guys see what I'm doing? Common mistake. Here it is again. We did a video that got so
many dang views about how to keep our goggles fog free. Well, this is not the answer. How many people,
this is your decision. You're just breathing your warm air right into the lens, getting that foam
wet. And then sooner or later, our goggles are jacked up, right? Especially on those days. Well,
when goggles are a necessity, let's remember that when I'm finished, I'll either leave my,
my goggles on my helmet, take my helmet off, or just straight up, take the goggles off
and then make sure that you place them so that your lens is up and you're trying your best
to not get any of that snow and wetness onto the foam. So it brings up another common mistake
that I can tell is happening a lot as well. And that is riding too warm. So we're wondering why
our goggles keep fogging. And with the introduction of like the heated goggle and some of those
things, that's helping a lot. But the idea of wearing a neck sock or a buff, a full blown head
sock. I see people taking all this stuff off. Their head is just sweating and they kind of seem
miserable. Remember that the reason why we're wearing uninsulated outerwear is so that we can
layer. And so right now I can already tell that I can get rid of one of my shells on the inside
here. And you guys will see that I'm wearing this, this puffy jacket here, having the ability to take
this thing off, shed this layer and go ahead and go into the tunnel bag or someplace waterproof,
knowing that boy, this thing later on, either for the cold trail ride home or in the event I've got
to stay overnight or heck, even just be out here for a while. Temperatures change, right? You don't
like the weather, wait three minutes in a mountain town. It's always changing. So having the layering
is smart. The ability to take it off and keep that temperature where you're nearly running cold,
head cold, a little bit of that cold around us. That's going to keep that temperature regulated,
especially when I'm working hard, keeping those goggles fog free. And overall, you're just feeling
better. You're not, you're not sweating. And then later, right? When you don't have all that sweat
around you, that's going to help you stay warm on your trip out. All right. Well, once again, guys,
big thanks. Hope you liked the video. We are, we're getting dang close to 40,000 subscribers. So
if you haven't subscribed to the channel, please do so. You guys, that just really shows us that
support and it allows us to get out here and, and build future videos. Hope you guys like this one,
the common mistakes for us. We see it all the time. There's definitely a lot more than what
I've even showed you today, but hopefully this is kind of a run through and it hits home with
a lot of you have just things that I see that are happening both on and off the snow. You guys
remember checking out your sled, making sure that the, the quality of your day, the ride can be
just about these few maintenance items that we're seeing protect ourselves, wearing a tether radio,
doing that transceiver check, making sure that your group is connected that way. And then obviously
the riding techniques, part of it, just go out there with the idea that it's about quality and
not about quantity, right? We can continue to just go, go out onto a snowmobile and do these things
over and over and over and doing them incorrectly. And all we're doing is stacking bad muscle memory.
So come out here, utilize these videos, start doing right. Leave those questions and comments
and we'll see you next time.
