Hot and Cold Water Dispenser Wiring Diagram Explained in Hindi @ElectricalTechnician

Electrical Technician
42 followers
2 Video Views·Oct 2, 2024
Friends, you must have seen this type of hot and cold water dispenser somewhere.
Now, the electrical connection of this dispenser is very simple.
And if you learn how to connect this dispenser,
then you can easily repair this type of dispenser and earn a lot of money.
So, how does this dispenser have an electrical connection?
Let's understand through this video.
Friends, the most important component of our water dispenser is its compressor.
The compressor's job is to cool the water.
You must have seen this type of compressor in your fridge or AC.
So, this compressor will cool the water.
Now, apart from this compressor, you will also find a heater in our water dispenser.
Now, if you go for wiring, you should know about the compressor's terminal before wiring.
For example, if you open the compressor's cover,
you will find three terminals there.
On one terminal, you will find R, S and C.
R means running winding terminal.
S means starting winding terminal.
And C means common winding terminal.
There are two windings in this compressor.
One of the two windings is connected here.
And one of the two windings is connected here.
Common wire is here, running wire is here and starting wire is here.
So, this was about the compressor.
Now, to start this compressor, we use a PTC relay.
PTC relay's job is to supply power to this compressor on starting winding.
As soon as the compressor starts, it will stop supplying power to this terminal.
It will supply power only to the running terminal.
Apart from this, if the water is cooled through the compressor,
and we want to stop the compressor after the water cools down,
we use a thermostat here.
This thermostat turns on and off the circuit according to the temperature.
Apart from this, you will find a switch behind the water dispenser
which is a cooling on-off switch.
You can turn it on and off depending on whether you want to cool the water or not.
This will turn off the compressor.
Apart from all these, you have to use a plug top here
through which power supply will be provided to all electrical devices.
Now, how will power supply be provided? Let's understand.
As you can see, there is a plug top here.
You will get fair supply from the pin on the right-hand side of this plug top.
So, bring a wire from the same terminal and connect it to the switch.
Now, bring a wire from the output terminal of this switch
and connect this wire to any terminal of the thermostat here.
Now, if it is detected through the thermostat that the water temperature is high,
then you will get power supply from this terminal in this condition.
You have to connect the first terminal of the PTC relay here to that terminal.
Then, you have to connect the power supply from one of the two terminals of the PTC relay
to the running winding terminal here.
Then, you have to connect the power supply from the second terminal of the PTC relay
to the S terminal of the PTC relay.
This means that the compressor will get direct phase supply from here
and at the time of starting the compressor,
power supply will be provided to the starting wire terminal through this relay.
Now, we have to provide neutral supply to this compressor
and we have to provide neutral supply to the common terminal.
But there is a story here.
See, the compressor is a very costly product
and we don't want our compressor to break down in any condition.
So, to protect it, we use OLP here.
The full form of OLP is Overload Protector.
This means that it is a device that protects from overload.
As soon as the current flow increases,
this device will cut the neutral supply.
Because of this, this compressor will not get neutral supply
and our compressor will stop.
So, here we have connected the one wire of this OLP with the common wire.
This means that we have connected the one wire of OLP
to the point where the negative power supply was to be provided.
Now, we will take a wire from the neutral point of the plug top
of this OLP and connect it directly to the second terminal of OLP.
So, here the connection of the compressor is complete.
Now, after doing so much connection,
we also have to see if the compressor is running or not.
To see this, you can use an indicator here.
This indicator will be called a cooling indicator
because if the compressor runs here,
then this indicator will glow at the same time.
And when this indicator glows, we will understand that it is cooling.
It means that the water is being cooled.
Now, connecting this indicator is very simple.
First of all, connect the neutral power supply to the indicator.
Now, the phase supply that will be provided to this indicator
will be provided from the output terminal of the thermostat.
So, we can either connect the wire from the middle
or we can connect a wire from this point
and give phase supply to this indicator.
This means that if the power supply is flowing through the thermostat,
then this indicator will glow.
And if the power supply is not flowing through the thermostat,
then this indicator will not glow.
So, the connection of this compressor is complete.
Now, if I connect this plug top to the power supply,
then if I turn on these switches,
then the compressor will start.
When it starts, the water will start cooling.
And as soon as it cools,
this thermostat will cut the phase supply
due to which this light will stop glowing.
And the compressor will also stop.
When the water temperature increases again,
this thermostat will start the power supply.
Again, the compressor will start cooling.
Okay, you must have understood this much.
Now, friends, let's also understand
how the water is heated in the water dispenser.
See, to keep the water hot,
a tank like this is installed.
There is an inbuilt heater inside that tank
whose terminal is shown here.
Now, you have to connect the power supply to this terminal.
Apart from this, there are two switches here
which are our thermal switches for protection.
As you know, if we heat the water too much,
then the water will become vapor.
And due to the formation of vapor,
our tank can explode here.
Or due to the high temperature,
the water will open up while being heated here.
So, if you don't want that,
then you have to use a thermal switch for this.
And not just one thermal switch has been used here.
Two thermal switches have been used here,
For example, if the water starts getting hot,
then one thermal switch will turn off the power supply.
But by chance, if one thermal switch
is not able to detect the water,
because it is hot,
it is not able to turn off the power supply,
then the other one should work
so that there is protection
and the water does not get too hot.
For such protection,
two thermal switches have been used here.
Now, let's also understand
how this heater will be turned on.
To turn on the heater,
first of all,
another switch is used
which is a heating on-off switch.
If you want to keep the water hot,
then turn on this switch
and the water will start getting hot.
If you want to turn off the hot water permanently,
then turn it off
so that the heater will not turn on.
Now,
we have to provide a phase supply
to this switch.
For this,
we will take a wire from this point
and connect it to the switch.
We will connect it to the phase supply
of the plug-top.
Then, we will take the power supply
from this switch
and connect it to the thermal switch.
I have connected the power supply
to this point.
Now, we will get the power supply
at this point
when the temperature of the water
remains low.
As soon as the temperature increases,
we will not get the power supply here.
At the moment, the temperature of the water is low
so we will get the power supply here.
Then, we have to take this power supply
and connect it to the other thermal switch.
Then, we will get the power supply here.
So, we will get the power supply from this point
and connect it
to a terminal of the heater.
Now, to operate the heater,
we also need a neutral power supply.
So, we will directly provide
the neutral supply from this point.
Now, the heater
will also start.
Now, after the heater starts,
we need an indication
that the water is being heated.
So, for the indication, I take
an indicator lamp here.
This indicator is my heating indicator.
Now, it is very simple
to connect this indicator.
What we have to do is
the power supply going to the heater
and the power supply going to the heater
from the output terminal of all these switches
will be connected to that power supply
and the indicator will be
supplied to that indicator.
Remember, the power supply
going to the heater terminal
will be supplied to this indicator
through that power supply
so that the light will glow
in the same condition as if the heater is on.
However, to make it glow,
we have to provide a neutral supply.
So, I will provide a neutral supply from here.
So, the heating indicator is also connected.
We have already connected the cooling indicator.
Now, we just have to connect
the indicator indicating
the on condition of the power supply.
So, to connect this,
we will take the power supply
coming from here
and connect it to this indicator
so that if the switch
of our plug top is on
i.e. if the power supply comes
then this light will get a phase supply
and this light will be provided
so that the light will always glow
as long as the power supply
is going to our water dispenser
from this power socket.
Even if I switch off this switch
the power indicator will still glow
because we have connected
the power socket to the power supply
and the power supply is available there.
When will this indicator glow?
When there is heating here
and this indicator glows
during cooling.
Now, let's understand
the working of this heater.
If you turn on this switch
then phase supply will come
from here to this thermal switch
and from this thermal switch
power supply will come to this thermal switch
and from here power supply will go
to the heater.
Now, if the temperature of the water
in this heater is low
then this thermal switch
will move the power supply
so that the water gets heated
through the heater.
But, when the temperature
of the water increases
then the thermal switch
gets open
and the power supply
cannot flow further
and the heater gets off.
So, the working of the heater
is very simple
and I hope
you will never forget
what I have explained
through this video.
If a water dispenser
comes to repair
then you will be able
to repair it without any problem.
If you liked this video
then please go to the channel
and comment in the comment section
and if you have not subscribed
to the channel yet
then please subscribe
because in future
you will get more such information
which will be very useful
for you.
I end this video here
Thanks for watching
this video.
