Waterdrop A2 Reverse Osmosis Hot Cold Water Dispenser Instruction Guide
Main Parts
User Interface
Before Installation
Installation Instructions
1. Installing the Filter
Step 1. Take out the filter from the pack and remove the wrapping.
Step 2. Open the housing cover and install the new filter by aligning the position mark of the
filter with the machine's mark. Gently press the filter until a click sound indicates successful
installation. Then reclose the housing cover. 2. Adding Water to the Tank
Step 1. Gently lift off the cover plate from the water tank and carefully raise the tank upward to
remove it. Step 2. Fill the tank with tap water. Step 3. Put the tank back in the dispenser and
cover it. Step 4. Press down on the tank to lock it in. 3. Flushing the New Dispenser
Step 1. Once the filter installation and water tank filling steps are complete,
please connect the unit to the power source. The unit will then initiate an automatic flushing
program. When the water tank status indicator on the screen lights up, empty the remaining water
from the tank, refill it with tap water, and reset. Step 2. The system will filter water into
pure water tank. When the light flashes, put a container over 1.5L, 52oz below and press
to fill it with water. Step 3. When the light for pure water tank full comes on,
please do step 4 again. Keep doing this until the two tanks are clean or the meter shows 100%.
It will take about 20 minutes. After that, the water is ready to drink.
Operating Instructions. 1. Water Dispensing. Step 1. When the screen is off, gently tap the
button to awaken the display. Step 2. Cup Volume Selection. Place a container under the dispenser
spout. Press the cup volume button to select the desired water volume 4, 8, 16, 20 or 999
maxoz. For continuous flow adjustment, press and hold the button. Step 3. Selecting the
temperature. Press the temperature button to choose desired temperature setting, cold,
room temp, warm, hot, very hot, and close to boiling. Step 4. Press the button to begin
dispensing water. Pressing any button will pause the process. The dispenser will automatically
stop when the selected cup size is filled. 2. Child Lock Operation. When the selected temperature
is 113 degrees Fahrenheit or higher, press and hold the child lock button for 1 second to deactivate
the child lock, then press the water dispensing button to dispense water. Press and hold the child
lock button for 5 seconds to turn off the child lock feature. This action will disable the hot
water safety feature. Please be cautious. After shutting off, press and hold the child lock button
for 5 seconds to reactivate the child safety lock feature. 3. Routine Flushing. Standby continuous
flush. After the machine has been in standby mode for 24 hours, it will automatically flush for 30
seconds. During this time, the water filter indicator will flash. Upon completion of the
flush, the machine will revert to standby mode. Cumulative water production flush. Once the machine
has produced water for a total of 25 minutes, it will flush for 10 seconds. During this process,
the filter indicator will flash. In flush mode, if the water tank is empty or not installed,
the machine will not enter the flushing state. It will wait until the flushing conditions are met.
4. Boiling Point Correction. Step 1. Press and hold the temperature and water volume button for
5 seconds to enter the boiling point adjustment mode. Step 2. When the temperature flashes at
203 degrees Fahrenheit, press the hot water button to cycle through the settings of 9 degrees
Fahrenheit. The adjustable range is 176 degrees Fahrenheit, 185 degrees Fahrenheit, 194 degrees
Fahrenheit, and 203 degrees Fahrenheit. Step 3. Press the dispense button or if there's no
operation for 10 seconds, the system will exit and save the boiling point data, which will be
remembered even after a power outage. 5. Favorite Mode Key. When the screen is on and functioning
properly, press and hold the favorites button for 2 seconds to enter the favorites mode editing
feature. Tap the temperature button to set the desired temperature. With the range from 59 degrees
Fahrenheit for ice water and 77 degrees Fahrenheit for room temperature, the temperature can be
adjusted from 59,203 degrees Fahrenheit in increments of 9 degrees Fahrenheit. The temperature
unit will blink. Press the water volume button to select preferred volume anywhere from 432 ounces
in precise 2 ounces steps. The selected volume indicator will flash to confirm the choice.
Press and hold the favorite button for 2 seconds or simply wait for 10 seconds of inactivity.
Alternatively, press the dispense button to lock in your settings automatically.
This will return to the standard standby screen and the favorite settings will be displayed.

