VQ35 Timing Chain Install | VQ35 Engine Build Part 3

The Engine Story
7 followers
All right welcome back to part three of the VQ35 build and in this part I'm tackling all
of the timing chain along with a bunch of the other accessories here on the front of the engine.
Now for the first part of this video I do paint the front rear timing chain cover
so if you're not at all interested in painting or watching paint dry definitely skip to this
part of the video where I'm doing more of the mechanics and the assembly of all this.
So with all that being said I'm going to go ahead and jump into all this.
Before I go and install the new timing chain and all the accessories on the engine
I first want to clean up and paint the timing chain covers.
Now in preparing this for paint I'm hitting it with a brass brush and hitting it with some 320
grit emery paper to get all the grime and dirt off of this along with a lot of the loose oxidation
that's on the surface. Once I have that good and cleaned up I'll mask everything off and then hit
it with some isopropyl alcohol to really make sure that there are no oils on the surface and
that this thing is ready for paint. Now overall I'm keeping the engine aesthetic pretty minimal
I'm going with sort of a solid black and silver kind of look so I don't want to leave these bare
I do want to add a little bit of color here so I'm going with a satin black with an engine enamel
and then I'm hitting it with a satin clear on top to make sure that this
thing seals really really well and is protected.
always a step to it that includes a baking process so that the paint can actually cure.
A lot of times people end up missing this step as it's in the small writing on the back
and if you do miss it the catalyst in the paint won't activate and ultimately the paint won't
harden correctly and adhere to whatever part you have. This ultimately ends up resulting in paint
flaking off really as soon as you put it on the engine and it goes through its first heat cycle.
This is a very crucial step and one that's actually a little bit tricky for me. See this
paint wants three increasing steps of heat starting at 250 a 400 and a 600 degree.
Now a lot of people usually have a parts oven or something that they can throw this in. I don't.
I have an oven but I use it for food and I'm not really particularly crazy about putting
painted parts in there where they're going to off gas and ultimately leave some residue behind
and the next time I put a pizza in there I really don't want to be tasting this or consuming
maybe toxins that are in here. So I had to start getting creative. Now this particular paint offers
sort of two ways to cure the paint on the part one being off an engine one being on. Now the off
engine kind of goes through those higher heat steps of 250 400 and 600 as according to the back
of the can but it does have one option with it being on the engine and going through two idle
steps and ultimately a running step. This to me makes me think that that 250 degrees is sort of
that sweet spot where that catalyst will activate considering it being on an engine. No engine's
running over 250 degrees at least without seizing so that's my goal. That's what I need to hit
and what I've done is actually pretty creative. I've taken my fire pit and lined it with that
thicker aluminum foil and basically I'm putting my heat gun in here at full charge and leaving
it for the time allotted on the back of the can. What's crazy is this might actually work. On my
first pass I got the part up to 250 degrees and I could already see ways that I could more enclose
this and keep that heat in without escaping. Now the thing about aluminum foil is it actually has
two sides to it. It has sort of a matted flat finish side and a more reflective side. Now the
reflective side is what I have facing inward to all of this so that that heat keeps bouncing around
and is focused in on the part. The thing is with enough encapsulation of this and no real heat loss
this thing is actually an oven and is actually baking the parts. So I've gone through my first
pass as you can see I've gotten this thing up to 250 degrees and roughly it's pretty uniform
throughout. There are a few spots that are that dip a little bit but nothing dips below 200 in this
so this thing is really actually acting like a good oven. So I'm loosely still following the steps on
this. I'm not going to be able to get up to the 400 or 600 degrees but I am going to stick to the
time allotted for these with 30 minutes in, 30 minutes of rest at room temp, 30 minutes back in
and I want to see if I can keep climbing the temperature in there and see how well this thing
can actually cure.
All right so now I have the rear cover on. I have it tightened down just finger tight but I want to
allow about 45 minutes to an hour to pass and let the RTV sit before torquing this down to spec.
So in the meantime I want to talk about an upgrade I'm making along with some of the other stuff I'm
throwing in before the timing chain. Now one of my biggest stressors for this build has definitely
been focusing on the overall oil use of this engine and anytime I can see a place where maybe
there's an upgrade or something to benefit it I'm always going to take it. So I was looking for oil
pumps I was trying to find something that performed better than stock and something that would be a
good addition for my DE and what I ultimately found was this. Now this is a VQ35HR oil pump
and it's designed to bolt directly into a DE. Now this is a really good and reliable upgrade.
It's also fairly cheap but you also run the benefit of this being an original Nissan part.
Now that's something I can definitely back considering all the design and engineering
that went into this from the factory and should be an easy upgrade to make definitely to this DE.
Now along that same spirit I'm going with an OEM Nissan water pump to throw into this.
Nothing really new or spectacular but definitely a new part to help with the longevity of this
engine. So I'm going to go ahead and throw these in while I'm waiting for the RTV to set and once
enough time has elapsed I'll go ahead and torque this all down. So I'm going to have to admit to
messing something up. At the time when I was doing the cylinder heads I didn't think these tensioners
were going to be an issue getting back in but the part I didn't think about were the actual bolts
that hold them in. The issue is these bolts are way too long to try to fit this in here now and
actually get them torqued down. As these aren't hex headed they're an allen keyed bolt and with
these in place there's no way to get any access to it to actually tighten these down. So at the very
least this means I need to take the front caps off the cylinder heads so I can actually get these in
and torque down. But I think what I'm actually going to do is take even a few more steps back
so that I make sure all of this is correct. Because at the moment I'm not crazy with the
protrusion of the RTV I'm seeing. I'd like to see more so I think what I'm going to do
is take all this back to square one and do it correctly make sure all this is right.
So I really don't know what else to say to that but I'm going to go back to make sure that these
are in correctly. I'm probably just going to fast forward through all of that and get back to this
part for this video but something I didn't take into consideration were these four bolts and they
have completely held up installing all of this. So that didn't take too long and overall I'm happy
I did it but now that I'm back on track I'm going to get this torqued down to spec.
All right so now I'm ready to go ahead and start tackling the timing chain on all this
but I want to make a quick note about timing specific to the build I have here and a couple
other notes specific to the DE. Now if you've been following this build one of the things you'll know
is I have higher compression dome pistons in this and these much more aggressive stage three
Breienkrauer cams. Now one of the things I have to keep note with that is these have a lot more
valve lift and duration to them and in combination with those dome pistons I need to make sure that
there isn't impedance of those two happening in the combustion cycle. Now like a lot of other
newer engines the DE does have favorable valve timing in it as it has controllers up here that
help alter the cam timing but it doesn't have a way to really go in and program any type of valve
timing and set cam degrees. Now if you're looking and doing research into this one thing you should
note is while the DE doesn't have that capability the VQ35HR does. The VQ35HR you can go into the
ECU and alter some of the cam timing and other characteristics so you can change that cam timing
and set it. Now while the DE doesn't have any type of that capability from the factory
the aftermarket does provide a kit from Gemwolf technology that you can basically come in and set
that cam timing to a specific degree. Now that means it is fixed there and it will actually
delete these oil controllers on top and basically bypass the variable valve timing in your cams
and just set them to a specific degree. Now I'm not planning to go that way I keep checking to
make sure that there isn't impedance between the valve and the pistons and I'm going to go ahead
and use the stock cams with all the accessory timing chain and all of that but if I do find
myself in the future seeing an issue or that I want to go with a route in just setting this timing
there is a kit out there and there is something that I could easily buy into and will be an easy
fix for this. So if you're looking to do something like that definitely take into account timing and
overall impedance with your engine if you're going to more aggressive cams as that will start
to interfere and that's something you should note now in the build. But like I said I'm planning to
use stock cams for all this and the overall stock components so it's going to be a pretty
easy timing chain setup in this and that's what I'm going to get into now.
Oh
You know what to do
And I think
Relax
You know what to do
Where do we go from here?
Don't let it rule you
Everything's gonna be all right
Everything's all right
You know what to do
Where do we go from here?
Don't let it rule you
So as I'm wrapping all this up I do have one last upgrade to make here to the front of the engine
and it comes in the way of this new mission motor thermostat. Now this thermostat has a key
difference from the stock one that comes on a DE where this thermostat will open at about 155
Fahrenheit and a stock one is opening about 175 or 180. Now this temperature difference
between the thermostats allows for one large advantage and that allows this engine to retain
more of its horsepower that would otherwise be lost to heat. So basically a thermostat that will
open at a lower degree will allow for more coolant to pass through the engine and allow this to run
cooler overall. So as I'm always looking for ways to gain a bit more power and to make this overall
more efficient this was a pretty obvious upgrade for me and definitely one I could throw in here
pretty quick.
All right so that is a wrap for this part of the VQ35 build. I am super excited about all the little
upgrades I have into this but I'm so excited to see this thing starting to look like an engine again.
Now of course I do still have some upgrades left in this which will be in the upcoming videos
but to see this thing starting to take form and look like an engine again has got me so excited
and I can't wait to see what all this is going to look like in the future. So definitely stay tuned
for what all I still have coming up for this and where all this is going but until then I'll see you
in the next video.
