Lecture 25 : Ironmaking slag recycling

IIT Kanpur July 201
20 followers
Sep 26, 2024
Greetings, I welcome you all to the lecture of this course, and till now we have been
discussing various types of metallurgical wastes. And now, we will be focusing on the
next aspect, which is basically the wastes that are generated in iron making and steel
making industries, which is probably one of the most important sectors of metallurgical
industries. And simultaneously, the wastes generated in the iron making and steel making
industries also become very much prominent. So, when we think of iron making and steel
making wastes, there are couple of important wastes that we should be focusing on. Of course,
the iron making and steel making industries are predominantly pyrometallurgy oriented.
And so, it is fairly relatively easier to guess what type of wastes we are expecting.
So, slags, iron making process slag, iron making slag, steel making process will give
us steel making slags. And of course, the following processes that are involved after
the conventional iron making and steel making processes will also in turn have their own
slags. And apart from the slags, we will also be
discussing about the waste water generation and its recycling. And similarly, we will
also be focusing on the scrap utilization. So, just like we have focused on the other
metals like aluminum, copper and zinc, we will also try to have the same discussion
when while we are discussing iron and steel making industry wastes. So, we will begin
our discussion with iron making slag. So, iron making slag will come when we are discussing
iron making and steel making. So, iron and steel making basically is the process that
generates the finished good of what we call as steel. And is one of the most important
steel, is obviously one of the most important metals that are available for mankind to use.
And this whole process has been investigated for lot many years. The process of using raw
materials and making iron and then following that we will go for steel making and then
utilization of steel for various applications. This has of course, been explored for lot
many years. Now, the different categories of wastes have been mentioned. So, we will
have slags of course, both iron making and steel making and we will have waste water
and we have the scrap utilization. So, we will be discussing these types of wastes and
of course, when we discuss about slags, it gets partitioned into iron making slag or
steel making slag. Of course, we can guess that these slags are going to come from different
routes. Iron making process is going to give us iron making slag and steel making process
is going to give us steel making slag. Now, the blast furnace slag iron making process
basically, the blast furnace operation will give us B F slag blast furnace slag. So, blast
furnace slags we will have to discuss something about it. Nearly 0.3 to 0.6 tons of slag is
generated per ton. So, we will write per ton of pig iron. So, safe to say that we have
let us say a blast furnace and we had our raw materials and we have our output. So,
the output in this case is pig iron. So, per ton of pig iron, we will have 0.3 to 0.6 tons
of blast furnace slag, which is basically acting as the waste stream in this case. So,
this is what we want to make and this is going to go ahead for the steel making process,
but blast furnace slag is something that is generated as a waste.
Now, what is the overall quantity of steel that is generated? So, let us just look at
some numbers. The overall quantity nearly million tons of steel has been produced in
and this figure is for 2002, 22 and this is of course, the global number. Now, for that
we will have one more statistic that is following that gives us nearly 1, 3, 4, 5, 6, 7, 8,
9, 0, 1 metric tons, million metric tons of pig iron again. So, we can just say that
this is the quantum of steel and pig iron that has been produced. Of course, this is
a global number and we can say that based on that what is the quantity of blast furnace
slag. So, just by multiplying it we can say that it is an enormous number and the sheer
quantity of blast furnace slag that is generated makes it important waste that needs to be
handled, that needs to be treated, that needs to be recycled.
Now, what really follows is basically the evaluation of the quantity of steel that is
used and the evaluation of the metallurgical waste. So, the iron making slag or we are
calling it as blast furnace slag. So, this has to be analyzed and then newer methods
of recycling have to be developed. So, the complete utilization of material is done on
a more comfortable basis. So, that the sheer quantity of blast furnace slag that is generated
can be directed for such applications. Now, we will also look at some of the most
more important properties of iron making slag. Iron making slag or BFS blast furnace slag
is basically produced in the iron making industry. We already have discussed this, but what are
the forms? So, we will discuss forms of BF slag. So, what are the forms of BF slag? We
see that these can be produced as air cooled, we will have pelletized or we can also have
granulated. So, blast furnace slag can be either air cooled or pelletized or it could
be granulated and then of course, we need to see the densities that are present. So,
this is the range of density of the blast furnace slag and we know that when the temperature
of the blast furnace is evaluated, we can see what is the temperature of blast furnace
slag. So, nearly when it is getting discharged,
so it reaches of a temperature range of 1400 to 1600 of course, plus minus 50 or 100 can
be seen here. So, that is the temperature range and at this point of time the slag needs
to be tapped. Now, this is a sheer quantity of heat that is produced in the iron making
heat. Now, we will try to put some numbers on that as well. We know that 1770 nearly
1770 m j per ton slag is the heat. So, this is the heat that is present in the blast furnace
slag. What it means is if we are able to entrap the heat that is present in the slag
that heat could be used for some other applications. Now, extraction of heat itself because we
know that the incoming slag is of the of a very high temperature 1400 to 1600 degree
Celsius temperature is coming. The slag is of that temperature and one has to extract
heat that becomes a bit of a challenge because one has to have devices and infrastructure
and facility that is capable enough of extracting heat and then cooling the cooling the slag
down and then the blast furnace slag is then used for various other applications.
So, what does it really mean? This quantity of heat can be equivalent to 61 kg of coal
61 kg of coal. So, 1770 m j per ton. So, if we are just using a significantly large quantity
of slag we would be getting equivalent amount of heat. So, per ton we will get 61 kg of
coal. Now, we will also look at other characteristics
of slag granulation of slag. So, granulation of slag can be done by water addition and
one has to do by some sort of applying pressure. So, you can just say some amount of pressure
is also added while adding water on to it. So, that some sort of granulation is done.
Now, what else 3 meter cube water is used per ton of slag. So, it does not appear to
be a very large quantity, but what happens is water pick up by the slag during this process
is observed. So, granulated slag when you are adding water with pressure what it does
is it picks up water with it and then we see the presence of water in the finished product.
So, this is what I am saying nearly 30 percent water is observed. So, this is what I am saying
in the slag when we are cooling it down by the granulation process and when we are adding
water with pressure this is going to happen. The other option could be when it is water
cooled and it is charged in a drum. So, this could be root 1 the other could be water addition
plus drum rotary cooling. Now, what this is basically we have a mechanism
of cooling we will have a drum which rotates. So, we will have a rotary drum and we have
the induction of water what this does is it requires relatively lesser amount of water
which means lesser water entrapment in the finished product. So, we can also think of
some sort of rpm. So, if this has 300 rpm we can have a significantly very less quantity
of water requirement. So, this really reduces the water requirement by nearly one third
of course, the values can change. Now, this tells us that there are various ways in which
iron making slags can be handled. Now, we will look at the chemical composition of iron
making slag and we will see why exactly this recycling of iron making slag becomes important.
So, we look at the chemical composition now we have various samples of iron making slags
and these are the references that have been used to collect the data. And we see that
there are some important observations here we see that there are some important phases
that are present in iron making slag and we know that these materials are usually present
in varying composition. So, Fe 2 O 3 Si O 2 Al 2 O 3 Ca O are important
phases and to some extent Mg as well Na 2 O K 2 O Mn O S O 3 because silica is already
mentioned here. So, we see that these phases are already present here and these are relatively
minor phases. These trace elements also play important role in imparting some of the chemical
properties, but of course, these are present in really smaller quantities. The major phases
are Fe 2 O 3 Si O 2 Al 2 O 3 Ca O and Mg O. Now, we will discuss why these phases are
so important we will see the variations. So, silica is almost always present in nearly
about 30 percent nearly about 30 percent alumina can range from close to 1 percent to about
20 percent. Similarly, Ca O can range from around 5 percent to 40, 45, 46 percent Mg O
is in the ranges of 10, 10s to 20s and Fe 2 O 3 can also be varying from relatively
being very less to be to about 40. So, what it really does is Ca O Mg O Al 2 O 3 and Fe
2 O 3 are important phases that are present in the iron making slag.
One has to think what are the important ways by which we can extract or separate these
phases to extract valuable materials out of it. So, if one aims to extract iron one has
to think what is the composition before if one aims to extract Ca O. So, one has to think
what was the composition before we even begin. Similarly, this analysis has to be done and
then we can devise the treatment whether it will be a pyrometallurgical treatment or hydrometallurgical
treatment or a pyro hydrometallurgical treatment and then extract these valuable materials
from it. One of the most important methods that is
explored as we have just been discussing about the energy aspects of the high temperature
slag that is getting generated is the heat recovery. So, one of the most important ways
of recycling iron making slag is actually recovering heat first and then recovering
the material. So, we will discuss this and of course, before we go beyond we should also
note what are the key areas of iron and steel applications. This is important because this
helps us understand why really iron making slag becomes important. So, we will just quickly
note them. So, we will have construction and infrastructure of course, construction
also includes infrastructure. We have metal production, we also have mechanical equipment,
we also have automobile industries and that also includes some shipment and other industries
that are related to automobile consumer goods. This tells us that of course, apart from these
iron making slags that we are actually discussing, we will also have some scraps that will be
discussed in the upcoming classes. These will be originating from such wastes.
Now, coming back to our focused topic which is basically why even recycling is important
till blast furnace slag. So, we have seen that one of the most important and attractive
aspects of this waste is the shear quantity. And if we are not investing our thoughts on
how to recycle it, we will be investing on where to store it. So, the most important
challenge that most of the industrial industries are usually encountering is the lack of land
resources associated to the slags. Now, we are generating pig iron. Pig iron will be
used for making steels, but at the same time slag is also getting generated and it is getting
stockpiled. When we have this stacking of slags, it becomes the slag stockpile and it
consumes the land resource within the plant premises, within the industries because we
cannot discharge the slag for into the environment. So, one has to really think of the land resources
that are available in the industries for better utilization and storing of slags or drosses
or scraps is not what land resources should be used. So, one of the more why we should
be recycling iron making slags, we will be pointing it out now.
Why recycle class furnace slag? So, we know that the phases that are present, we have
just seen the phases that are present are CaO, MgO, Al2O3, Fe2O3 and of course, SiO2.
These phases are present and they have significantly large quantity of these phases and Fe2O3 requires
recovery is important. Of course, the composition can change and it depends upon how the pig
iron was made and what was the composition, but still it some quantity of Fe2O3 is still
invariably present in the iron making slag. So, one has to think of recovering that recovery
of iron. Similarly, one can think of recovery of calcium and other phases also and bringing
back to the material cycle. The other reason that we have just discussed
presence of limited resources and which resources are we talking of land resources. So, storage
of waste slag is the challenge. First we do not have resources and the second these materials
cannot be stored in conventional open spaces. One has to think of the hazardous leaching
tendencies of the phases that are present. So, it can affect the surrounding land resources
and the environment. So, conventional route of storage is not an
option. So, the environment of course, we have already seen what resources are we lacking
here and the environment degradation due to of course, leaching of heavy metals. Leaching
of heavy metals can cause the environmental degradation. So, now we will be discussing
how really we should be developing the recycling routes.
Recycling strategies for blast furnace slag. So, we already know that of course, the material
has to be recovered. So, whatever slag is there it has to be recovered, but the slag
that is coming out is already at a very high temperature 1400 to 1600 temperature degree
Celsius and the heat we have already seen. Why not tap the heat as much as possible before
we even think of material recovery. Let us think of heat recovery and that is how some
of the recycling strategies, the modern recycling strategies have been developed and of course,
there are other methods also. One of the most important strategies include
CO 2 mineralization, which is basically the carbon sequestration that has been implemented
in lot many laboratory experiments and it is being explored in other scales of operations
as well. So, stainless steel, the steel making slag of course, we are discussing iron making,
but steel making slag has also some good applications for the carbonation and then of course, there
is the carbonation that is done in direct and indirect route, which we will be discussing
in the upcoming lectures also. So, people have tried to use iron making slag as well,
but it has been seen that this route really does not give as good result as steel making
slag. So, the preferred material would be the stainless steel slag. So, in this case
when we think of CO 2 mineralization, steel making slag makes more good raw material for
compared to the iron making slag. Now, we will think of waste heat, we know that the
temperature is of 1450 to 1650 degree Celsius. It is and we can use glass furnace slag as
thermal energy storage material, because of this high temperature and comparing just like
CO 2 mineralization, where steel making slag was a better material. Glass furnace slag
is actually a better material for this application for waste heat recovery. People have explored
the possibilities and they have said the glass furnace slag should be first used for waste
heat recovery and then for material recovery. So, that is the reason why glass furnace slag
is first used for this application. And of course, what are the other applications after
it the waste heat has been used, has been recovered, we can always think of cement making
industries, cement making construction, infrastructure applications. Of course, the glass furnace
slag will be used as a one of the additive raw materials and then it would be converted
to some other applications with the other raw materials. And then it would be brought
into the construction applications, the evaluation for civil engineering applications is done
on the basis of their own tests. So, only after it passes through those tests, it will
be used as a raw material. Now, what are the key challenges that are
associated with the waste heat recovery, because of course, we know that CO 2 mineralization
steel making slag is a better option. So, one of the most important challenges, we will
be noting low thermal conductivity. So, the slag itself is a low thermal conducting material,
so the heat transfer may not be efficient. The slag has corrosive properties, corrosive
nature, because of so many various phases that are present. Of course, it is present
at high temperature, one has to cool down and the equipment has to sustain heat as well
as this corrosive nature. And then, so when we think of waste heat generation,
during the process itself, the cooling process is done in such a way that the finished product
may not be of good applications. So, one might think of making it as a raw material for let
us say construction applications, but the cooling route would be a bit different. Heat
recovery would end up in making phases that may not be applicable for various larger applications
of glass furnace slag. So, these are the typical challenges that one need to address while
developing the routes for efficient waste heat recovery. We will now be continuing from
this point in the upcoming class. Thank you.
