3.2 & 2.8 24v VR6 Comprehensive Timing Chains Guide

Engine Nation
3 followers
Sep 18, 2024
Here is your legend, to quickly skip to parts you may find useful.
All right, Mason you you lost the Toreg lottery dang
Make sure you drop a comment below and let us know which step was most helpful for you
She was stuck on a crack pipe
So this is exactly why we acquired a new thermostat housing as you can see right here
plastic
thermostat housing has deteriorated and
Is no good
Remove the exhaust manifolds, which I want to avoid doing. All right, so we're popping this valve cover off
Let's see how healthy this engine is
Probably not very considering it came out of a Toreg
That's not good that's one of the worst ones I've seen
Look at that. I wonder why we have some correlation codes here
So right here is our
notch on the inner part of the vibration dampener and
Down here is a mark on the front cover that we need to line up the two
So we're just gonna turn it over a bit
So we hit that mark
All right
So we've cranked this thing over to TDC on the flywheel and right now our camshafts are not lining up with
The base of the cylinder head. So we're definitely out of time. We're actually out of time
Probably on the crankshaft or intermediate sprocket
So once we open it up, we're gonna see why probably but yeah, luckily this engine did survive. We bought this Toreg
With a no start condition first assumptions might have been fuel pump
Luckily, we actually got it running to drive it out of the underground parking lot that it was in just enough to put it on
the trailer
But for the most part this thing did not want to run
If you're working on this engine in a transverse application your engine might be hanging quite a bit forward
So if that's the case
I highly recommend you actually drain some of the oil from the oil pan like a quarter of the oil
Because once you take this lower timing cover off if it's on an angle the oil is gonna be up to here and it's gonna
Be constantly puking out which you don't want when you go to reseal these timing covers
So I like to pry between the camshaft gear and the timing cover. You're gonna want to avoid prying where the
Camshaft position sensors are of course, there are dowels up at the top here. You want to pull back first and then
Just like that. Ooh
Wow, look at that. It's literally just chilling right there
Just when we remove the timing cover
Our guide is in several pieces
So on the inside of this timing cover here you actually have a second o-ring that seals the coolant galley
Ideally when you do this job, this is a seal that you're gonna want to think about
Getting a new one. There's also an o-ring here that seals the oil passage for the tensioner through the timing cover
So should probably recommend replacing this as well pry a few different places here. We have four pegs
Holding this guy to the block
The gear loose no, it's not loose actually
So we have a case of the intermediate gear actually failing so I've never seen it this bad either
Wow, so I guess if you really don't do your oil changes
The intermediate gear sprocket is a point of failure as well. See all that metal worn away. Basically eat that's deep grooves
Into this side of that thing
It's straight-up missing its teeth. So it didn't actually skip timing because of
the broken guides
Miraculously, it's skipped timing because it had worn away so much at this intermediate sprocket
That it was just able to skip
All right. So if your engine is already perfectly in time, I encourage you to use a paint pen
But maybe don't rely on it because the paint pen marks with the oil or whatever they can rub off fairly easy
So I'm going to show you how you would time this from the factory with with no marks because that's what we're gonna have to
Do here because timing has already skipped it's wrong. So we got to reset it from the very beginning
so if you can rotate your engine to top dead center, I
Recommend that you look through this window on the intermediate sprocket here at the very back on the oil pump housing
Cover is a vertical line. You can see it on video here and there is a little circle on this gear
That is perfectly aligned with that line
Now if we look at the bottom here, you can see there's another window, but this one has an arrow now
Best case scenario. We actually want this arrow pointing to that line up top
so
Typically, I would rotate this
Another full two revolutions to get to that point since our engine is out of time already
We have to take all of this apart and line it up from scratch
So as long as that we're at some sort of PVC, that's all we need at the moment
All right. So to take this apart, there is a bit of an order of operations that I recommend
To avoid touching as many stretch bolts as possible
We're going to take the bolt off for the intermediate gear
this will allow us to take this these two gears apart and
Then we technically won't have to take off any camshaft gears. So in order to take this off
It's a bit tricky because obviously if you just put a ratchet on it, it's gonna spin
So what you're gonna want to do is have your 27 mil socket ready on your breaker bar and put this on the crankshaft
Pulley and then you're gonna use this to counter hold so that you're able to remove and retorque this bolt
So since our bottom end chain tensioner is still on we will be able to do this
We will be able to counter hold the crank and remove this bolt here right now
The breaker bar is actually just sitting on the ground so I can technically do this myself
And there we go
so these two gears actually separate from each other right now, it just came off of the
oil pump
Bracket, but there we go. So this gear we're gonna throw away. We're gonna replace you can totally remove this
Gear off of the chain
Your hydraulic tensioner will pop out. That's okay. We're gonna replace this the next thing I would do is
Take the lower tensioner off
Okay, so these two bolts you have to be extremely careful with sometimes they can be very
Hard to remove and the the flip side is that Volkswagen used very shallow
Fasteners, so my five mil heck doesn't go very deep into this
So if you just have this slightly off you're going to strip out the fastener
So I'll show you right now that this should be alright if we hold it perfectly straight
That one wasn't too bad. This one wasn't too bad probably
So if you get into a situation
Where you have stripped these out, I'm gonna show you how to basically
Get them out. What you're gonna want to do is buy some sort of triple square bit like this
This is a m6 triple square. I encourage you to round out the fastener even more
And then you're gonna want to take this triple square and hammer it into the block
If your fastener is really stuck hammering it will shock the threads and help with removal
And then the flip side is this will dig splines into the bolt enough for you to be able to remove it
There is actually a revised bolt for this tensioner that you can buy. It is a forks t30. The depth is obviously a lot better
All right. Now with the tensioner removed
We should be able to basically take this whole chain with this guide
And remove it so
Technically we can take the chain on it first and then this is on pegs
So we don't need to mess with these fasteners at all. We just slide the guide out just like that
That is our full lower timing chain
Setup removed. All right for the upper timing chain system. We're gonna remove this guide first. It is two six mil Allen's and
Then there is a peg down here. You don't have to remove this peg. This guide just clips onto it
So we slide it off just like that then our whole chain up here is free
So basically I'm gonna go around with my thumbs like this lift it up over everything and pull it out the bottom
Now this guide is also pegged on so once the chain is removed and the other guy
You'll be able to push it down here and slide it out. Just like that
That is the order of operations. You should remove the timing components
All right
Now with all of our components removed, this is the time that you want to take to remove all remaining silicone
From the cylinder head to the block just clean everything
Use brake clean try and get as much oil off of the head gasket as you can and and dirt and whatever
So you're gonna want to clean the oil pan a little bit down here. Take this silicone out all
Around where the timing covers go
Just a light scuff of the head gasket top and bottom
Here and here and then as far as the timing covers go
Pretty much the same thing. So you got all of this silicone from the oil pan to remove
These edges here the obvious ones and then where the upper timing cover
seals to the lower timing cover on the lower cover as well as
The bottom of the upper cover and then you've got this area here with your o-rings that you should replace and
I would recommend just scuffing up where the valve cover gasket sits and that's pretty much it
Of course when you have your lower timing cover removed as well
You will want to replace your remaining seal. So I will show off how that is done briefly
I'm going to show you all of the marks that you need to be concerned about on this engine
Okay, so we've got two marks
For each camshaft, there's a small arrow here and then there's a little notch on the BVT housing here
So these won't ever actually line up perfectly perfectly, but I'll show you how they should look once we are fully in time
so there's those two marks there and
Then at the front here, we've got our where our camshaft locking tool would sit
So you'll notice actually that these slots are offset
So when you're at TDC, you want to make sure that the smaller end is at the top that way you could actually
Theoretically fit the camshaft locking tool in
We don't actually have the dedicated camshaft locking tool
but visually you can get away with not using it if you visually confirm that
Everything is perfectly level with the deck of the cylinder head. Alright, so we've also got our intermediate gear sprocket. So
You're ideally gonna want it to be exactly here so you can see the little window with the arrow in it is
Facing the line on the block and then the last mark you're gonna want to worry about is basically this ground tooth on
The crankshaft to this main bearing where it meets the block. There is a line
So you want those to line up basically perfectly?
Right now our tooth is actually one tooth down
So we're gonna need to fix that with the 24 valve you have variable valve technology
And we have camshaft gears that move around
independently from the cams, so
Basically when the chain is driving the engine it rotates in a anti-clockwise
direction you're gonna want to take your cam gear and
Rotate it all the way to the left on both of them
If you want to know if you've mixed up your cam gears for some reason and you want to know which is which the intake
One will always have more
variability, okay, so we went ahead and corrected the
Crankshaft now, we've got to correct our camshaft. So you want ideally a 30 mil
Wrench like this
If you don't have that you could probably get away with an adjustable
And so right now our cam gears rotate it all the way to the left at their stop
We want to kind of roughly line them up here
so that's probably
Where it should be gonna do the same quickly on this other one
Somewhere like that okay now
I'm gonna go around to the front and look at where our slots are sitting okay, so it looks like I just about nailed
the intake
But the exhaust is currently out
So I'm gonna rotate slowly my exhaust
Okay, so doesn't need to be a hundred hundred percent perfect, but it needs to be pretty close
because we are going to lay chains over top and then spin the motor over once we're good all right, so
Unfortunately, we don't have Iowa's chains
We actually got an INA kit which should be pretty good
But the one thing with the INA kit when you get it is that these chains are actually not linked
anyhow, we had to put this INA chain back together and
Originally, we purchased a special tool
That did not end up working very well
so if you have these INA chains
And you want to put them together all you need is a flat circle punch and ideally
some sort of anvil or metal surface that you could hammer on and basically
Once you put the chain link together all you have to do is punch
the top and the bottom at a slight angle on a solid surface and that will be enough to
Effectively crimp the chain properly, so we've gone ahead and done that already on on the one link
The Iowa's chains actually have copper links to help you with timing a little bit
But if you follow this video
That shouldn't matter you should be able to still time the engine without those special copper links all right
So we're gonna get our new lower chain and guide. We're gonna set it up. Just like this push it down
Then we're gonna grab our intermediate gear, and we're gonna try and wrap it around the chain
And now this point we have to try and line up our
mark back with the block
So I'm gonna keep skipping this
gear
So that's a bit too far
And there we go so you want to make sure that when you tension the chain
Your mark is pretty much
in line with the other line
Now you can go ahead take your chain tensioner, and you should have this little piece holding the tensioner
All right, so these bolts are gonna get torqued to 10 Newton meters if you don't have a quarter inch
Torque wrench I would highly recommend getting one even if it's a
cheap mechanical one
All right, and then you can go ahead and pull your lower tensioner pin. I would recommend just
Putting some slight tension make sure it's good there. This does have a ratchet mechanism
Inside for when there's no oil pressure now. We're gonna go ahead and put the next guide on
Which has got to be this one so just like we did when we removed it
We slide it on and push it up. Don't push it back all the way
You'll hit the BBT housing pull it out slightly and then there you go
Just like that. I'll throw our sprocket on
These gears are keyed to each other so there's a little square here. That's gonna line up with the other one right now
I'm not too concerned with where the chain is sitting because we're gonna correct it
You're gonna want to make sure that you have some slack over here
And then basically this side once we put the guide on we want to have basically no slack here
It can be one chain link too tight or one chain link too loose
There's only one way that you're gonna get this black guide on so right now. It's a bit too loose
So I'm gonna try and fish one link over just like that
To the tensioner side now that our chain is loosely mounted like this
We actually want to mount our guide, so we've got the chain in loosely
We're just gonna see where we're at by mounting this
Guide into the cylinder head. I think I nailed it first try here
So actually if I take this off just to demonstrate
I mean, it's not gonna push the chain up any higher than that, but this is where you want to be
So for example if I move some slack
To the opposite side so if I go right now and put the guide in
It's a little tight going down here. It'll go, but now we can't push it up vice versa
It might be too loose up here
So basically the goal with this is to have just enough slack to install your black guide and any remaining slack
Should be on the opposite side for the tensioner
Okay, so now we're at the point where we want to double-check our work
So we're gonna go ahead and reinstall the upper cover without the lower cover installed
Just gonna pop this guy over
Okay, I'm gonna put one bolt over here. Maybe one over here
At this point you don't need to worry about silicone
All right, and then we're gonna throw our tensioner in now when you do your final install before you do your filing install
You're gonna want to put this thing in a little container of oil and squish it a few times to prime it with oil
So that you have good oil pressure on startup now since we're just rotating the engine over
I'm just gonna throw this in as is now to verify timing
We need to rotate the crankshaft not once but twice if we rotate it just once
Our cam locking tool theoretically wouldn't be able to go in
Because it's below the deck surface of the cylinder head. So we need to go twice
In order to make sure that the engine goes back to proper TDC and then we can check all of our marks once again
Yeah, there's more compression now than there was before
Think we're on the money there so you can see theoretically if we had a cam locking tool. It's basically perfect and
Now let's go to the camshaft gears up top
So this is what our marks look like
Right here on the exhaust side. There's actually a bit of a range. So there's the
Initial dip there next to my paint mark and then there's this little range here. So there's another lip here
So right now we're at the edge of that range
This is acceptable
The actual chain tooth is about in the middle of that now on this one our gear is pretty much
Perfectly in center with our little dip of a mark on the BBT housing
If you look at it like from top down, it actually looks like it's off
But if you look at it with the angle of the gear, it's bang on
So that's one thing that might throw some people off
All right, so down here we've rotated it over twice our camshaft marks we've confirmed are okay at the bottom
You can see the circle and the line
So we don't have the arrow pointing to it anymore
But that's okay as long as this is perfectly in the center now
You'll find that if we rotate this engine over two more times
This intermediate gear will actually have the arrow pointing to the line
So as long as it's pointing completely at the top or completely at the bottom
Then it'll be completely in time
Now if you ever have a situation where you feel like you are always half a tooth off
The culprit is is always the intermediate gear
So let's say you had this arrow instead of completely up or completely down
It could be pointing at a three o'clock position or a nine o'clock position
The engine will still run okay, but you will have cam correlation codes as a result
That is because your camshafts will always be basically a half tooth out of timing
We've also confirmed right now that our ground tooth is lined up with the line in the engine block there
so basically we've spun the engine around twice and we've confirmed that all our marks are okay and
Now at this point we could reassemble
All right, so we've confirmed that our timing is good. Now. We need to torque this intermediate gear sprocket
so
The torque spec is 60 Newton meters plus 90 degrees
Online 74 75 foot-pounds has been thrown around
So we're gonna see where we get with just using the factory torque spec
So initial torque 60 Newton meters right now. We are counter holding the crank
It is crucial that you have your upper timing cover installed for this with the tensioner so that you don't skip timing
I've gone ahead and marked our angle
Now we're gonna go ahead
Give it 90 degrees. It's 40 so far
so I
Don't recommend if you're going to reuse the bolt
To use a factory torque spec because there we just exceeded
187 Newton meters, which is the max reading of my torque wrench. I would say probably
80 foot-pounds or higher is acceptable
okay, so we've cleaned everything up and
We need to now replace this rear main seal
All right, so I just put it on a flat surface like this fairly hard surface
Take one corner with an extension and a large mallet
There we go. We'll quickly clean the inside there obviously
Professional install tool looks more professional, but this will get the job done. It'll put it perfectly flush
All right, so
We're gonna leave this install tool in this will help the seal go around the crankshaft
Make sure you just give this crank a quick wipe so there's no debris and then we're gonna go ahead and
Silicone this cover. So we're gonna silicone here the surface the top underneath the head gasket
so one thing that I love doing on these is
making sure that I
silicone
Basically underneath the head gasket and on top from the factory. There is
Technically not any silicone here. They just silicone the corners
I like siliconing the whole surface that way you don't get any sort of oil sweating like they do from the factory
you can go ahead and begin by laying a very thin bead like so quite thin and
Then I personally like to spread the silicone out with my finger
I call it controlling the spread because if you put it on now, you know, it'll be okay
But you might get some extra squish here or there. Well, why not take advantage of the full sealing surface and
Just kind of rub it in
Now when you do this, it does dry quicker so you have to be a bit quicker as well and
Then down here. You only need to seal it to about there
So the other thing that I like to do
You'll notice I'm not using a whole lot of silicone
You do actually get
Some silicone being scraped off when you install this
Between the oil pan and the head gasket, so I would recommend just laying
Very small amount of silicone and smearing that on so that if you get some sort of rub off on your cover
You still have a little bit of silicone that you initially applied down here or on the head gasket
To save the day and just like the factory. I am going to fill in a
little bit of gaps with a bit of extra silicone and
At the base of the head gasket on the bottom and each side
So you're gonna want to cinch a few bolts on as quickly as you can
You're gonna want to cinch down
the bottom corners of the timing cover
Wait before I tighten those I'm actually just gonna wipe this silicone
All right, so I've got all my upper timing cover bolts in just a little bit tight
Not not too tight
The reason for that is I want to try and cinch these two covers together as much as possible
So now we've got these bolts installed. I'm gonna zip them in
And as you can see a bit of silicone actually oozed out of there
So we've got pretty much a dialed seal at this point in time
We can torque all of our upper and lower timing cover bolts the line between
Not being tight enough and too tight is very fine on these if you're not tight enough
You're gonna have an oil leak if you're too tight
You're gonna pull threads out of the engine block or especially the cylinder head these guys
threading into the aluminum cylinder head very prone to
stripping so
Basically, I would say a quarter inch torque wrench for this job is a must
So we're gonna go ahead and torque all of our timing cover bolts to 10 Newton meters these
Larger ones. I would just go as tight as you can by hand
Or probably would like something over 20 Newton meters should be okay, so
All right, so we have installed a lot of the accessories
Now it is valve cover gasket time. So rate where the cylinder head
Seals to the timing cover. We're gonna put a bit of our TV here on
both sides
Then we're also going to put some in these
These dips down here and now we can go ahead and fully install the valve cover
So another crucial area where the torque spec matters is the valve cover gasket same thing you could risk stripping
The cylinder head holes or you could not have it tight enough
these
fasteners do have a metal insert that bottoms out on the
Bottom of this or the top of the cylinder head
To allow for perfect squish of the new valve cover gasket every time
We already did our initial torque
in a
Decent sequence. There's technically no torque sequence for these
But I would recommend going from the inside out in a star pattern
torque on the upper
tensioner is
44 foot-pounds I
Went a little over 50, but yeah. Alright, so the engine is back in the car all timed up
So that concludes today's comprehensive timing guide. Hope you guys enjoyed watching this video and see you in the next one
