How to Carve Patterns in Wood. Ep.2,...

Wood carving: Tips and Tools
229 followers
Hello, good afternoon, this is Bernardo from Woodburn Studio
and we're going to continue the how-to videos on how to carve
chip carving patterns from my book of patterns and someone suggested to carve
the number two pattern which I asked some of you
so that's the pattern that we're going to carve now. Okay so again we need
transfer marker, we need a laser printed pattern, ink
will not work with this method, a piece of wood, chip carving knife
and that's it, let's go. Okay so remember we need to
tape the pattern onto the surface otherwise when we are transferring it
it could move. Time for some transfer marker and
remember once we see the design we stop applying the liquid because we
don't need it anymore. There you go, now the solid piece of
material flat just to wrap it because right now
the pattern is still not there and there we go.
If there are any spots that we didn't fully transfer the design we just can
mark it with a pencil or a pen whatever you have in hand
and that will do. So let's start from the outer ones
so in this case we could carve one by one like I'm doing now.
Okay here we go, so now we removed one right and what we can do now
is to carve in a series of cuts meaning instead of carving only one and then the
other one and then the other one what we can make is we repeat the same
cuts for these exterior patterns then we make
the second cut for each one of them and then we're gonna make the third cut
this way what we do is go faster. So let me show you
so here and then I forget about the other two cuts and I move forward
to this one. I don't know if you can see but
all the outer parts of the chips are carved
and let's move to the second one. This is the second cut
we have already cut this side here and now we're carving
this side of the chips. Okay so I don't know if you can see it
but now all these triangles are holding on
onto one single line and once we cut this third line for each one of them if
we cut it pretty fast to carve the center part of the pattern
we only need to make two cuts for each one of the patterns
so as you can see we carve here and then we avoid this angle
by adding a little bit of curve right and as we get
closer to the center what we do is we slightly remove
the knife yes now it's too deep for the center
so what I'm doing is I'm pulling the knife back
out I'm hoping that you can see it you see
and now here I'm only using the tip of the knife
you see only the very tip see the difference
the depth in the middle of the chip and the depth
at the end of the cut. Again we start with the very tip
of the knife and as we move forward we can put it inside
and here again we try to avoid that angle
by cutting in a curve. The reason why I'm saying that we should
only use the very tip of the knife when we reach here in the center area
is because if we stick the knife very deep
in the center area of the pattern what's going to happen is that we're going to
break the walls. Also the first cut that I'm going to
make is in the opposite direction of where
it's empty because if I carve this way like this
I might break this wall here because there's no
protection cut so now what I'm going to do is I protect
this wall that I'm going to just create here you will see in a moment
by carving in the opposite direction. So tip of the knife
as I move forward I can go deeper and as I reach the end of the pattern I
slightly remove the knife. We avoid the angle by carving in a curve
I go deep and from now on I just slide the knife
out looking left over here and you can already see the wall that I'm
talking about. Right here for all the chips this is
that the weakest point of the pattern
the center that's why we should only work with the very tip of the knife when we
reach these areas. Okay so from now on I'm just going to
give you a close-up of the carving process of the pattern also this
is my way of carving it you can find 10,000 different ways of carving this
same pattern you can create your own patterns
I hope you enjoy the rest of the video and let's go.
Now we have two weak sides for this chip so what I like to do here is just
stick the very tip of the knife make a little mark
at the beginning of the chip on each side
what I do is I slightly make a mark at the beginning
like that and I repeat the same process for the
other side. I make a little mark the tip of the chip is kind of protected
now if I push from this side all the strength is gonna go
out from these cuts that I made so now I'm not scared to follow the cut
and go deeper as you can see the tip already popped out
like this and now you see the tip I can push it away
and it's here now I have protected both walls
and I can confidently just carve the other part of the triangle like that
this is the full pattern carved and now we have a few options here
we can decide to carve this line here that we made for each one of these
petals or we can carve the inside triangles and
here we have the option of the single line
here and down here we have the option of carving both the inner triangles
I will leave this to your own creativity and maybe you can find different
ways to carve it this has been today's pattern
hoping that you can learn something from it
if you have any questions any suggestions feel free to let me know
I will give you now options for the next pattern
and that's it see you in the next video
