Monarch Butterfly sterling silver handmade silversmithing how to make jewelry by Hanzy Driscoll

Traditional Metal Crafting
21 followers
Wow, check out this beautiful butterfly. What? It's made out of silver. Yep, check it out.
Handmade, hand-fabricated monarch butterfly ring set with citrines. Completely handmade.
Turned out awesome. So here's the step-by-step of how I made it. First, I start with the telephone
using it as a light table to trace the design. So what I'm doing is I found an actual monarch
butterfly on Google Images so that it's anatomically correct. Now I got tracing paper
and duct tape. So what I'm going to do is I turn the light off so that you can see
the image really good. And I got this fine tip pencil and I'm tracing the design.
Got the top wings. Next, the bottom wings. You can see it there, tracing in. The thing about
why you have to trace it and not just copy it on a copy machine is that thin parts need to be
thicker. So you have to translate that image into being able to be made into jewelry.
Cutting out the tracing paper and what I'm going to do is I'm going to super glue it
onto that silver sheet there. It's a very small piece of silver sheet and so I had to like sit
there and figure out how to make it work. All right, we got our super glue. Gluing it on there.
And like I said, it's used with, I, uh, that image is, uh, traced on there with pencil.
So what I do is I avoid rubbing my fingers on there as much as possible
so that, you know, the pencil doesn't, doesn't wear away. All right, got it. Next, I'm making
the butterfly body. That is square wire, pretty thick, sterling silver. Cut the piece and I'll
make a little notch for, see that little round piece? That's the bezel where the stone's gonna
get set. So I'm notching it so that when you solder it, it's all flush and nice. All right,
there we go. All right, onto the solder pad. Charcoal block. All right, that's the fire coat.
It protects the copper and the alloy. Sterling silver is 925 parts pure silver and 75 parts
copper. So that bezel was flush with that, so I had to put that little piece of silver sheet
underneath it so that that lip sticks up above the flat part of the square wire,
because you have to have metal to push, um, onto the stone to keep the stone set. All right,
soldered it on there. All right, so next we're gonna cut these wings out. Super, super thin,
uh, saw blade there, and we're cutting away. Sawing out stuff, um, it just comes to you after
time, after you've done it enough. If you've never, uh, if you're just getting into silver, uh, smithing,
um, it would be good to start with a big project like this, because, uh, by the fourth wing there,
you'll have it dialed in a little better. All right, cutting the outside. Next, I'm putting
in a one millimeter ball burr, and I'm drilling through the silver sheet with the ball burr.
Ball burrs are awesome to use as drills because, uh, they don't, uh, drift. Super exact. All right,
you can see my thumb is, uh, see how the burr is pressed against my thumb? I'm lining up the exact
spot with my thumb and using it as a guide. See how my thumb is holding the side of the burr?
So those holes that I'm drilling through there, those are where you're going to feed the, um,
saw blade through. And then the edge right there, I'm just doing little ball burr, uh, half,
half drilled through for detail. All right, so I feeded the saw blade through,
and I'm cutting out the pattern. We got one done, two done. What's awesome about doing the handsaw,
obviously, everything in jewelry is done with a tiny, tiny handsaw, is that you can go slow.
So it's not like, just like, uh, you can, like, uh, not make mistakes. You can just go as slow
as you want. And you can go fast as you want too. It can get ripping. That little white, uh, chunk
down there in the bench pan, that's wax. And you, uh, put wax on the blade every once in a while,
which I love because skateboarding, you use wax on curbs. So here is the upper wing,
zoomed in a little better. There I am cutting out the detail. Now the traced on there was good,
uh, translation to make the thinner parts thicker, but still when you're cutting it out, you, it
changes just a little to make it appropriate. Cutting out the detail. Now I only, uh, filmed
the upper and lower on one side because it's just repetitive. All right, there we go,
finishing up with that. There we go. Now here is the ring. I previously soldered this together
already. And so, um, what I'm doing now is I'm making this silver square wire round after I
soldered it. There we go. Saw it, or I'm filing in a little flat part to where it's going to connect
to the bottom of the butterfly. All right, so here what I'm doing is I'm removing the superglue
and the paper. I soaked it in the pickle and, um, it soaked it for like an hour. So it's, uh,
that superglue is just falling right off of there. Okay, so now this part's a bit tricky.
There's the solder. Silver solder is made out of silver. This part's a bit tricky because you want
to line it up even, obviously. So what I do is I made the body kind of, um, square to the bottom
of that charcoal block so that the bottom wings were square. You know, I could gauge the distance.
That's the fire coat. There's the, uh, torch. That little pick there that looks like a nail
is a solder pick made out of titanium. So you pick up tiny balls of solder
and you, um, put them into place. And then you, uh, do the heat and you heat both sides
and it melts. It flows the solder in between the two, um, places that you're working on.
All right, got it going. So what I did is I added more. See, now I'm gonna solder the two wings
together at the, that part so that there's, uh, they're stronger. Make the whole thing like a one unit.
Okay, now I'm gonna solder. There's the back. I turned it upside down. There's that ring I just made.
Heating it up, adding the solder, flowing it on there, melting the silver onto it, and then
melting the silver and the ring together. So what's happening here is I'm, uh, it was just a
little off. So I'm flipping it, looking at it, flipping it, looking at it, flipping it, making
sure it lines up nice. There we go. Got it lined up. And so you put it in the pickle. It's a very
light, light acid that dissolves that fire coat and it dissolves the oxidized copper.
Dissolves the oxidized copper on the outer layer of the metal. There we go. That's how it looks
after you get it out of the pickle. All right, that's before it's polished and everything. That's
just raw. So next step, we're gonna set the stones. These stones are natural citrines.
I went for the natural yellow because of, to bring some accent of yellow into the situation
because of the monarch butterfly. Okay, so what I'm gonna do is I get a burr, I get the stone size,
see that little notch in the bench is, uh, used for, like, support. So I got the stone.
So I'm gonna measure the stone and get the right size burr for that stone.
Okay, we got the burr. Now I'm drilling out, grinding out the seat, the seat for the stone.
Takes a while. You go slow because you can definitely very easily have that thing set
in there crooked. So now I'm filing the edge off around the bezel lip. And now I'm pushing
the metal down. The reason I filed the little edge off is so that the metal was thinner and easy to
push over the stone. Okay, so now I'm measuring out, doing the layout for the stones. I found
the center of the bar diagonal going down lengthwise. And then I did equally spaced.
Now I'm using a drill bit and I'm drilling out the holes. You drill out with stones,
you want the back to be open because you want the stone to be able to be cleaned.
All right, so I drilled out the seats with the burr. Now I'm cutting, um, with the saw blade
in between those settings so that the metal can be pushed onto the stone. Lining them up,
making sure it's all even. Okay, now we got the first stone almost in there.
One of those burrs hit my finger there. You can see it's a little bloody.
All right, so I got the first stone in there. Pushing, excuse me, pushing the bead over,
pushing that tiny corner of metal onto the stone.
All right, on to the third one, or the second one. Oh yeah, that is the third one. Okay,
on to the third one. Getting it done. This one edit of the stone setting was an hour and 16
minutes. All right, so now I'm sanding the tail to make it roundy. And I'm cutting notches into
it for detail. And there's a, um, triangle so you can see the bottom. I did it roundy on the bottom.
Now I'm cleaning up pre-polish on the wings and the whole entire jewelry with, uh, pre-polish.
All right, so now it's down to the final polish here. Got that, that's for the inside of the ring,
that tiny little soft cotton wheel, which I can't show you that I'm gonna do it because
one hand is holding the camera. So there is the pre-polished and then there's the final buff,
high polish. I'm just gonna show you the little corner there because I have to hold that with
both hands. And you got to be delicate when you're polishing. So after I polish it up,
it's going in the cleaner, the ultrasonic. All right, we got it going. A lot of work, a lot of hours
went into this. Check it out. Turned out absolutely awesome. Super beautiful. Super delicate.
I mean, really, it's pretty much art jewelry, you know. It's not like for daily wear or whatever.
But it's cool and it's fun to do as a jeweler because, uh, you got to make some things that
are just fun every once in a while. Yeah, it looks cool on the rose. Yeah, turned out awesome.
Hey, thank you for watching.
