How to make a pinch pot ball tea light holder, a great festive gift idea

Making ceramics and glass
106 followers
Hello and welcome to another Paul Armstrong Ceramics. So for this video I thought I'm
starting to plan things to make for the festive season so I thought it would be nice to make a
tea light and I've got a very simple pinch pot tea light that I make for gifts at the
festive season so I thought I would show you how to make one of those. It's just a sphere shape
with lots of holes in a pattern, any pattern that you want to make, so you could change those to
suit. So I hope you enjoy it. So the first thing we're going to do is turn our clay into a ball
so we need a solid round ball. It doesn't have to be too neat.
And what we're going to do is turn this solid ball into a hollow ball. So we're going to cut
this in half. If you wrap the wire around about halfway down, put the handles into one hand
towards yourself, the other hand stabilise the top of the clay and then just pull through.
From here we're going to take one half, pop it in the palm of your non-dominant hand,
take the pad of your thumb and press down into the middle. What we're aiming for
is a thickness of about five millimetres, somewhere around there.
We're then going to tip the clay up slightly and press towards the outside edge. We're leaving
this flat edge here because we're going to put the two pieces together and I want something to join
but this is going to be about five millimetres as well. We're then going to turn the clay slightly
and press again and keep repeating that all the way around so you end up with what looks like a
daisy pattern pressed into the clay. I'm also pressing against the palm of my hand and trying
not to press against my fingers. If you press against your fingers you'll end up with marks
from your fingers in the outside of the clay and while that's not terrible it just means you'll
have a bit of a tidy up to do later whereas if you press against the palm of your hand it keeps
it much smoother on the outside. Once we've got that kind of daisy pattern on the inside
we use the pad of our thumb and just even out the thickness a little and you can do that by
smoothing. Again I'm pressing against my palm not my fingers to try and keep the outside smooth.
So this should even out the thickness.
You want to get rid of those points where we've pressed down with the thumb and even out and
smooth the inside as well. As we're doing the holes through this the inside will be visible so
we need this relatively neat.
And then we can go around and just lightly pinch the edges to make sure
that they're the thickness that we want.
So
try not to pinch too much around the edges or you might just flare
the piece out so the sides just all fall down and you end up
losing the spherical shape. When one's done we then do the other side in exactly the same way.
So we press down to the middle, tip it up, press to the outside, turn and press to the outside and
keep going around until we have the daisy pattern. And then we even out the thickness and smooth
the inside. The key with the second half is we need to make sure that this ends up the right
size to be able to fit on top of the first half that we did. So we need to make sure that it's
not too big or too small to fit. Again I'm smoothing against the palm of my hand not my
fingers wherever possible.
So this clay is very wet and so these are very flexible still at the minute.
So I'm going to dry these off before I assemble them and I'm just going to use a heat gun, a
page stripper this is, but you can use a hair dryer, you put it in front of a heater, you could
just put it in a warm room and leave them there if you need to. It could be that your clay is dry
enough to start with. This was very wet clay that I was using to begin with so it needs a bit
bit of help to become a little bit stronger. If I tried to join this at the moment
it would all collapse in on itself and I would struggle very much to keep this spherical.
So I'm just going to give it a quick blast with some hot air.
When you use the heat gun you should be able to feel a difference in the surface
of the clay as well as how flexible it is and how it moves. You can see these are holding their shape
much better now. I've got a flat bottom in this where this sphere is sitting on the table
and as I'm going to keep this one as the base I'm quite happy with having that.
I'm just going to go around and make sure this is all a nice even thickness.
I'm then going to join that half to this one and to do that I'm going to score and slip
to stick the two halves together. So I'm just scoring
the surface then I'm going to join and I do that for both surfaces
and then pop some slip on. Slip is just watered down clay
so you just use a bit of the clay that you're using for making and add a bit of water to it.
You can if you don't have any slip at all just use water but not too much. The top one has just
slotted inside the bottom a bit too much on that side so I've opened it up and I'm going to rejoin.
Now where we've got this join we need to make that disappear so we're just going to scrape
the clay over. Try not to press in too much otherwise you'll create more of a hamburger
shape than our spherical shape but we want to make the join disappear so we are literally
scraping clay from one side over the other. I'm using a wooden flat tool
and I'm using the edge of that tool I'm not going in with the end like this I'm using the sides
and the flat because then I can go over and smooth.
Okay so I have a mark here that's where I made the adjustment on the side so I'm just gonna
fill that in a little bit and because I'm afraid of trapping a little pocket of air in there I'm
going to put a bit of slip in there because where there's slip I can't trap air.
There we go now you can see the shape is altered slightly as I've been doing this and I've now got
something that's not spherical really anymore so as I've got the air inside I'm going to use
the support from the air to reshape this so I'm just going to go around gently re-tapping
and turn this back into a spherical shape. I do want the flat bottom because I need that
for the tea light so that's fine but I didn't want a really wide bottom for this
and so we can now have the shape back again. So the next thing to do with this is to smooth
so I have a nice soft rubber kidney I put it in my fingers so that I've got my thumb on one
side my fingers on the other and then I can curve it and I can use it in this curved shape
over the outside of the sphere just to smooth and tidy where I've done the join and all the
marks from the building. You can get rubber kidneys in different
firmnesses so you can get soft ones, medium ones and firm ones.
The soft ones are great for smoothing, the medium ones are kind of good all-rounders
and the harder ones are great for shaping.
Once it's smooth and you're happy with the shape we need to dry off again a little bit.
At this point we need it dry enough that it can hold its shape and I don't have to worry
about altering it when I handle it so I can now go in and do some more
of a final smooth and tidy particularly around the bottom. This can slightly change the shape
again you can make it lift a little bit more so it's not quite such a kind of heavy bottom sphere
and reverts to a slightly more spherical shape again. Okay so we need to cut the bottom out to
give us a space to put our tea light so I've got a cookie cutter and I'll roughly place it
in the center of the bottom and then very gently I'm going to press and spin the cutter
until it should go all the way through. It has on one side and not the other so I'm going to use my
knife to decide that it didn't. There we go okay so we can now see the join on the inside here
so I'm going to just go in and neaten all of that make the joint inside disappear the same way as
you did with the join on the outside and I'm just going to use my thumb
around and neaten all of that up. Remember not to do any of this work with the sphere on the table
and if you put the sphere down you'll end up with a flat side because you're working
against the flat surface so whenever you do this pop the sphere in the palm of your hand
and keep it nice and round. Nice shape back a little bit there we go and then this piece
that we cut out is going to be
the base that we put the tea light on so I'm just going to roll it out a little bit
because we need it a bit bigger than the hole we have to cut out and I'm going to get a cutter
that's bigger than this one to cut the base. This spare edge that I've just cut off
I'm then going to turn into a little coil
I'm going to smooth the edge of this base that I've just cut out just to neaten it off a little bit
and then I'm going to put
the coil in the circle on the bottom
okay leaving enough of this edge for the thickness of the sphere
so
score where that coil is going to go
pop a bit of slip in place
and put the coil back
two things to join up line it up
where you want it
and then we're going to just
bend the coil down on the outside edge of it into the base
tidy and smooth with my finger
okay remember when you're making this circle the tea light's got to fit inside
and whatever your shrinkage is for your clay you need to make the allowances for it
and now our sphere should sit on top of our base like that
okay my next job is to decide what pattern I want to do
for the hole cutting and for this one I was thinking a bit of a spiral pattern
so the first thing I'm going to do is use one of my wooden tools to draw in a spiral
so I'm going to pop my sphere onto a whirler so that I can turn it while making the line
for the tool now that I have it on the whirler I can use this tool to mark in my spiral
and now I have a hole cutter that has like a dagger curved blade which means I can cut
holes of all different sizes with just the one hole cutter so I can
have a bit of clay
with your holes
I want to cut out the further I press the hole cutter in the bigger the hole is
so
you can get hole cutters that are one size
and so you might need a set to do lots of different size holes like this
okay I've just given that a bit of a dry now that I've finished all the holes and made this
a lot stronger so it's much sturdier so that I can go around and get rid of all the excess
bits of clay on the inside I'm going to do this first with the flexible metal kidney
just go in and get rid of scraping away as much as I can with the kidney
okay I'm then going to use a damp sponge and just wipe on the inside the reason for doing
this is twofold one is for neatness so that the light can get through the holes better
but it's also a safety issue because if you have any sharp edges on the inside here and
somebody puts their fingers in when they're dealing with the candles they can cut themselves
this just gets rid of those sharp edges
you can use the damp sponge to tidy
more generally
and then the last bit of tidying to do I'm going to use a paintbrush a wet paintbrush
and just go in and tidy each of the holes which is time consuming but a good idea
because again it keeps the holes clear for the light to shine through makes things a bit safer
and tidier you can use a needle tool if there are any holes that have filled in so you can push through
the holes to make sure they're clear
and then just go around and tidy everything up
and this is the last job so for the making
I'm going to I think glaze this in a white glaze with some copper oxide in this role so it should
give me a little bit of green under the white and I will show you the final outcome in a youtube
short and on my social media once it's all finished probably in a couple of weeks time
thanks for watching my video I hope you've enjoyed it
if you'd like some slightly more in-depth tutorials or just access to more of them
then I have an online membership that has more in-depth videos and more videos of different
project ideas as well as looking at things like glazing and finishing firing all of that side
of making in clay if you'd like to check that out you can check it on my website
