Sorceress New Valvetrain Explained With Jesel!

Engine in Focus
4 followers
May 27, 2024
Here is a look at our new valvetrain @JeselValvetrain has been working on! We take a look at what will be getting changed compared to the old valvetrain design and what some of the challenges we are working around! Big thank you to the guys at Jesel and Ben at @EFIUniversity1 for helping us with this project!
Okay, so it's pretty simple to understand where we're at now, Jaisal, and everybody has been
following along our trials and tribulations with the valve train.
And we're here and we're going to essentially be talking to Grant here at Jaisal. He's the
one that knows the project intimately. He's got it brought up in his laptop. Grant says hi over
here. Hi everybody. He is the maestro. Actually, he's going to make this thing all better.
Guaranteed to run... What's the warranty going to be on this thing, by the way? Warranties.
We don't need a warranty. No, where we're going, we don't need warranties. So it's kind of fun.
We're just talking about the business part of this thing and how he's modeled this thing in 3D.
And as he's talking, you know what? I should video this because a lot of people ask the questions
like what essentially is changing from the old two-bolt stand where the rocker arm was held on
by a 516th fastener, two of them, and how has it progressed? How is it different now? And
I'm going to let Grant explain how it's different and what actually what this would be here now.
So basically what we're doing is this would be the head as it comes from Dart, which is
for individual exhaust rocker stand, individual intake rocker stand per cylinder. It's not a bad
deal. It's quite antiquated. Works for some applications, but we can make it better.
So what we're going to do is basically just going to come, we're going to mill everything down flat,
make a nice surface to work with. So this would be the machine variation.
You'll notice there's some holes. These are the original locations. They're going to get plugged.
We're going to put in inserts. We're going to leave this hole alone because it already
goes into the intake port. We don't want to add another hole into the intake port,
so we're going to go off to the side. The new hole location will be
somewhere in this general area of the port, but it won't protrude in,
so we don't have to worry about oil getting in the fuel or in the motor.
Biggest advantage is what we're doing. We're coming in with a one-piece, and it's pretty
standard, but a one-piece rocker stand. So where the original exhaust bolt was, we're going to plug
that. Drone tap for our 5.8 coarse thread insert, which is capped off, so it seals the water jacket
versus the time cert that's in there is open. It's not blind, so water can come up through that
fastener. On the right side of the exhaust rocker, we're actually going to come through the shaft,
through the stand, into the cylinder head with a 7-16 stud to tie everything together
so that there's absolutely zero chance of lifting an exhaust rocker again.
Leaving the original fastener for the intake, we're adding another fastener
at a straight angle, so one is going to retain the four-degree angle that's in the port. The
other one is going to be straight. It's out of the port, so now we have two fasteners holding
down the exhaust rocker into the head. Two fasteners, as was before, holding the intake
rocker down into the cylinder head. We're going to take it a step up, and instead of using our
standard 5-16 shaft, we're actually going to use a collet-style shaft. Now this collet-style shaft,
what it does, it allows us to use a larger fastener into the cylinder head on the exhaust
rocker. On the intake rocker, we're just going to use a stud into the stand because there's not
material in the head to allow us to put a stud in. The collet basically clamps the shaft,
sits in the trough, and then, you know, a stud in the head adds a lot of rigidity
for trying to have this shaft basically walk in the stand. Now this style setup uses bronze
washers for thrust. Basically, with the tolerancing, there's no room for the rocker to move.
No end play, yeah. There's no end play. Now these bronze washers have cross-drilled
radiuses in them to allow oil to get down into the bearing. This baby isn't going anywhere. No.
Typical parts for us. What's that, if you want to tell them, what's the alloy on the
arms themselves? Are they similar to intake and exhaust? Same alloy? Yes, yep, they're both made
out of 4140. Shafts are tool steel, pins are tool steel, rollers are tool steel. What's the
diameter of that roller there then? Wheel diameter is 550 thousandths of an inch. Are they both the
same? They're both the same. It's a quarter inch wide roller with needles. The adjuster is a high
polish ball adjuster. Will they have, on those fasteners, the ball adjusters, will there be two
different lengths on the ball adjusters between intake and exhaust, or are they going to share
the same length? They are identical. They're identical, okay. Yep, same components between
intake and exhaust rocker other than the body itself. The shaft is just rotated around 180
degrees. Grant, what's the ratio? Is the ratio the same between the exhaust, the rocker arm ratio,
the same in the intake and exhaust, or are we going to split them up? We're going to split
them up. So the intake ratio is going to be a 1.85, and the exhaust ratio is going to be a 1.75.
There you go. The exhaust pivot length is two inch, the intake pivot length is inch 850. A
lot of people ask those questions, so there you got it, right from the guy himself. It's pretty
amazing that Jessel's got enough resources to come in here and take our head's use, by the way,
and I guess I'd consider model them and want to take on a project to the size where they'd
get the information that's needed, do a design on it, and fundamentally make it all start to
finish, cradle to grave, whatever you want to say, make it all happen all the way down to the size
of the fasteners, machining them and doing them, and Grant's the man that's been holding this
project by the hand the whole time, so it's pretty exciting to hear this right from him.
We've been waiting for a year, and it's well worth the wait. We're going to get it done right.
So again, this will be the new exhaust bolt location.
It's pretty much as close as I can get it to the center line of the shaft,
based on real estate that's available and what's already a hole in the head.
This will be the stud through. This is the existing intake bolt location that's going
to be on the four degree angle, retaining that. This will be the new intake bolt location,
and again, as much as I want to put a stud through on this side,
there's not enough real estate based on what's been removed from the cylinder head already,
and if I put it on this side, the port's only about that thick. It's just going to rip it right
in. Yeah, that's right. I know this is going to be a challenge. It wouldn't be near the challenge
here if this thing didn't have water ports in it. We'd have a lot more meat to work with here on
these different scenarios. That's it. That's it. That's just wild. Yeah, and thank you for taking
on this task too, because it's a big one. It's a big one. It's my pleasure. Thanks, Jessel,
for everything, and before I want to close out here, I want people to realize that it was Ben
Strader. He's over there. Say hi, Ben. Ben was the guy that introduced me to Grant here, so it truly
is Ben's connection that's made this all work, and I'm grateful for both. Thank you, everybody,
for watching.
