Máy siết bulong - Nó rất cần thiết nhưng giá nó loạn cả lên. Xem hết video trước khi mua hàng Phếch

PTA-ND
4 người theo dõi
1 Lượt xem video·20 thg 6, 2024
I just bought a hand-held DeWalt drill
This is what's inside
A manual
A cable
A 22mm socket
A screwdriver
A battery charger
It looks pretty cool
2 batteries
DCF887
The code is DCF887
DeWalt
If you haven't used a DeWalt drill yet
You may think this is a brand
But in fact, this is a fake
Made in China
It's not a brand
I bought it for a little over 1 million
If it was a brand, it would be 2-3 million
Only 1 million
Put the battery in
Very simple
Hold it very firmly
You can see there are 2 modes
Rotate clockwise and counterclockwise
Close and open
If we close it like this
It's in the close mode
Or screwing in
In the screwing in mode
It will give us 2 speeds
We can control 2 speeds
By pressing the start button here
This is the high speed
Press it again, it will change to low speed
Low speed
High speed
You can hear the machine
This is high speed
You can hear the machine
This is high speed
Low speed
You can hear the machine
It's softer
With these 2 speeds
It depends on our purpose
If the screw is small and light
We should set it to low speed
If the screw is big and large
We will set it to high speed
It's a little inconvenient here
We need to press the button
So the light will turn on
Then we can set the speed
If the light is off
We can't set the speed
Can't set
If the light is off, we can't set the speed
When the light turns on
We can set the speed
That's the screwing in mode
If we push this button to the side
Push it to the side
This is the screwing in mode
With this mode, it only has one mode
There are no two modes like the speed of screwing in
But it has another mode, that is the stop mode
Auto stop
If you don't choose auto stop, you just press it and it will turn continuously
And if you choose auto stop, it has a light here, it will be bright
Then you press this
Press and hold, but it only turns a little bit, it's flickering
Press and hold, flickering, press and hold, flickering
The purpose of this mode is to reduce the speed of screwing in
What is the purpose of this mode?
The purpose of this mode is that when you remove the screw from above
For example, when we press this
And the screw has been removed
It only needs to turn a few times, it will stop
To avoid the case that the screw will turn out, it will fall straight out
And it may fall to the ground
And the mode to screw in, it doesn't need
The purpose of the auto stop mode is that
It means that it only turns, it turns a few times
Turn a few times
The screw has been removed
We can turn it by hand to avoid the case that the screw will fall
Here, you can review the whole appearance of it
Very small
On the top of the machine, it has 3 lights
These are the 3 lights that report the battery
And on the back, it will have 3 more lights
For this battery, it will have 3 lights
It also reports the battery capacity for us
As you can see, the battery is still strong
This battery is also strong
Now I'm going to weigh this machine
See how heavy it is
Now I'm going to weigh the battery and the machine
About a little over 1.6 kg
More than 1.6 kg
Both the body and the machine are more than 1.6 kg
Now I'm going to remove the battery
I only weigh the body of the machine
When you buy a machine, you notice
The heavier the machine, the stronger the power
That's the principle
In addition, it is also related to the battery
With the speed control unit inside
The body of this machine is about 1.1 kg
Almost 1.1 kg
If you buy a machine that is too light
About 800 grams
The machine is a bit weak
Now you find it on the market
Now the machine is a mess
For those of you who buy this machine
You should equip yourself with this box
What is this box?
This is the head of the drill
The head of the drill
This is a set of 20 pieces
From drill 8 to drill 32
Here you see
Pretty big and sure
This is the head of the drill
The head of the drill 22
This is also the head of the drill 22
The size is the same
But this one is longer
The one on the market is shorter
If you buy this length, it will be easier to open
So what do we buy this machine for?
This is the reason
Suppose you need to remove this cone
Then we use a hammer
Right?
We catch it here and remove it
Can't remove it
You see it
It will slip
You see
It will slip like this
Can't remove it
And how to remove it
I have shown you in a previous video
But when you have this machine
I will show you
Very easy to remove
You see
One shot
Remove
The other one
Just one shot
One snap
You see
Just one snap
Two snails
Especially if we shoot nails or screws
We need to use this head
It's okay to shoot
Now I will show you
How to remove the snail
With a small machine like this
Can we remove the snail?
You have just seen
How to remove the snail
In one click
The snail is removed
Very simple
Here I have a tool
I will remove this snail
When you remove this snail
It will be very difficult to remove
It will slip
But with this machine
In one click
Shoot out
Too simple
Here I remove it
Too sure
Remove
Now I will open it
Let you see what's inside
You can see inside
I see the plastic is quite perfect
The details are also quite sharp
With a fake machine like this
This is our speed regulator
3-phase speed regulator
You can see above
This is the 3-phase engine
This is the speed regulator
There is only one button
Here we will have a lever
This lever
There will be a lever
To rotate the engine
I see this speed regulator
It looks pretty sharp
Because I also have
A fake machine
But it looks a bit bad
The price is cheap
So it looks bad
The price of this machine is more than 1 million
It looks sharper
This is its motor
And the hammer
This is the 3-phase engine
It is removed
It's a pity that this engine
It doesn't look like a block engine
But two pins
This pin and this pin
It's stuck in the plastic
And the rotor
You can see it inside
It's tight
The rotor is quite tight
Because our rotor
It's stuck in the plastic
And the other end
It's stuck in the plastic
That's it
This plastic
It's tight
This plastic
And the rotor
It's not the same size
It's tight
I don't know if the new motor
It's stuck
The magnet is very strong
And the stator
The wires are tied to the stator
The motor is 3-phase
It has 3 wires
I will open it
The led
Remove it
There are only 3 lights
If you want to make it brighter
You should change the light
And reduce the voltage
But we should calculate it again
To avoid the case that the led is on fire
This is our stator
At the bottom is the stator
The stator
This stator
It will be connected to the stator
You see here
This is the stator
And when it rotates
The motor rotates
It will make this stator rotate
And it will close
If the force at the top is too heavy
Then this stator
It will have a spring
This spring will press down
Then the stator will fall down
Then it will hit
And if the force
The force at the top
It's small
Then this stator
It always touches this stator
And when it rotates
This stator always rotates
And if this stator
If this stator is too hard
For example, there is a screw that is too tight
Then this stator will rotate
But the motor will still pull very well
Pull and lead to this stator
It will fall down
This spring is hard
I can't press
It falls down
Then it pushes out
It creates force
Hammering
See
It keeps rotating
Hammering
Here
This stator
The motor will be plugged
In the middle
And it will rotate 3 stator
And here
There will be another stator
Its mechanism
And its structure is just that
It must be said that inventing these
It's pretty smart
Although it's small
But its opening and breaking force is quite strong
For the force or not
It is related to several problems
The first is this 3-phase motor
It must be strong
The rotation force must be large
If you want a large rotation force, it must be related to this stator
And the battery
The battery must discharge strongly
And this stator
Its discharge current must also be large
It leads to the motor
It must be designed to rotate
With extremely high speed and strong
And the second factor
It is the hammer
This hammer
Its weight must also be heavy
And the heavier it is, the greater the breaking force
So when you buy
These drilling machines
But the force is large
Usually the machine will be bigger
Compared to small ones
I will test the charger
For you to see
I will plug in the battery
You see
When you plug in the battery
It will turn red
And when the battery is full
It will turn green
When you pull the battery out
It will turn green
Now I will open the battery charging box
For you to see
Here is the charging box
Inside
There is nothing
Except for 2 cables
And the charger
It uses a power supply
This is the power supply
A normal power supply
This is a diode
It will shine
Up to 1,000,000
This is the generator
Generator and the FET
It is integrated in this
And this is a power supply
It will transfer from 220V to the charging power supply
This battery
The charging power supply is about 20V
This is the charging source
And here
I will open the battery
Inside
This battery only includes
2 FETs
And here is a
This is a
Here is a
There is a
You can see the result
Very easy
10 cells
And this is the brown battery
18650 battery 1600mAh
4.2v 10 cell battery
Let's see how much is the voltage of the two batteries
Because the battery is 20v
This is the main voltage that is supplied for the converter
20v 19.11v
19.11V
Here it will be 20V
So here it is the real amount
There are many machines that it is written 118V
It is written as a myth
It is written to let consumers see
The higher the voltage, the stronger it is
But in fact it is not
It only has 10S and it is only 20V
You do not believe
You just buy a mask
You go back and check it out
This fake mask
This mask is from China
They sent it to the Vietnamese
They stick it on
You can stick it on
Do not trust these masks
I just shared with you
A new hair dryer
With a price of less than 1 million
You choose to buy a fake mask
But the fake mask is less than 1 million
You can buy
Thank you for watching
If you find this video interesting
You can comment below
Don't forget to subscribe, like, share to receive more videos. Thank you!
