Have You Tried The Lisa Pavelka Peel Polymer Clay Technique?

DIY Cute Things
114 followers
Hi guys, Samantha from GSImoTutorials here and welcome back to another video.
So, to start today's video off, we are going to actually be taking a metal leaf.
And I just want you to take those and put them into a small pot.
And we're just going to be breaking it up because we don't want it in full large sheets for this.
This project that I'm going to be showing today is also a great way to use up any scrap leaf that you may have lying around.
I don't have any at the moment, but just keep in mind that this would work very well for it.
So I'm going to be using copper, silver, gold and black.
And I've just got a pot so that I can contain it all once I've done this.
But I'm just going to use my fingers to rip it up into small pieces and mix it around together.
Okay, and there we go.
And you can do this with any colours of leaf that you want, but I'm going with these.
Now, I've just got a piece of black clay here rolled out on my thicker setting.
And I'm just going to take a brush.
You can use your fingers if you want to.
And you might need to encourage it a little bit.
But I'm just going to take that metal leaf and just scatter that around.
And then brush it onto my piece.
I'm using a brush because it will help lay it down well and it will scatter any extra pieces that we may have.
Because we're going to have a lot of leaf laying down on top of each other.
And by using the brush, you can kind of move it around and have it scatter.
Okay, and there we go.
And it's a little hard to see when it's just lying flat down like this.
But hopefully you can see there how it is completely covered in metal leaf.
Now, please make sure that you just burnish that on.
You just need a regular piece of paper.
I wouldn't advise using a roller because the metal leaf might stick to that before it's been properly situated on the clay.
So just give it a quick burnish down like that to make sure that it's stuck properly.
And there we go.
Okay, then I'm going with an animal print pattern today.
So I've got a stamp for that.
And that's also why I chose the colours of metal leaf that I did.
So depending on the stamp that you decide on, you can change up your metal leaf colours.
I'm going to put that down onto the clay.
And I'm going to just use an acrylic block to press down on it and get a nice even pattern.
Okay, then I'm just going to lift that up.
And it shouldn't have stuck in the stamp because we have all that metal leaf.
But still be careful when you're lifting it up and out because it still can stick a little bit.
But it should be okay.
There we go.
And we've got a really nice impression.
You can't see much because it's just all metal leaf still.
But we're going to reveal that pattern in a moment.
And the way we're going to do that is I'm just going to take some clear tape and just lay that over the surface.
Don't press too hard because you just want it on the top layer.
And peel that off.
And you can see there how it will lift up the metal leaf.
And I will burnish it a little bit to get it to pick up the leaf.
But you can see there how that will look.
And just go over it a few times just to really clean up that image.
Okay.
And there we go.
You can see how that looks.
And I'm going to leave the texture because we can give that a light sand later on to make the black shine a little more and stand out a bit.
But anyway, put that to the side.
We're going to work with that in a little while.
And I'm going to bring over a stamp that has a radial pattern.
And I've also dusted it with corn starch so that it doesn't stick to the stamp because we haven't got any metal leaf this time around.
And I've also dusted the back just so that my fingers don't stick.
And I'm just going to press that the way that I normally would.
Okay.
And then that one.
And also lift out carefully.
You never want to be ripping textures out because they will sometimes stick a little.
I can see on this side it's stuck a bit but it's okay.
I'll lift it from a different angle.
And I don't need the whole piece so it's okay.
But that's an example of why you go gently.
And there we go. You can see the pattern on that.
And then I'm just going to get that centre point right in the middle.
And I'm just using a doughnut.
Cut.
And there we go.
Then I'm also going to have brought this over.
And I'm going to try to do a rough half and half.
Of the giraffe pattern and then the leopard pattern.
Cut that. Make sure to get a good press.
And lift.
And you can obviously use the rest of this.
This isn't going to go to waste.
Same goes for the middle bit.
You can use that for lots of leftover techniques.
It's not going to go to waste.
Okay.
And then I wasn't able to show it.
But I have cut these in half.
Just across like so.
Because my head would be like right over here if I were to show you that.
Hold on. Let me try to adjust that lighting quickly.
There we go.
My head would be right over here if I were to do that.
But I have cut them in half.
And now I'm going to cure those for about 40 minutes at Primo's recommended temperature.
Just to get them nice and hard so that we can handle them.
And then we'll finish up our pendant.
Okay.
And there we go.
That's easy enough.
Then I'm going to pop those to the side.
And I'm going to bring over a piece of paper.
That has a piece of black rolled out on my thinnest setting.
Just burnished so that it's nice and even.
And I'm going to take these pieces.
And I'm going to start with this one.
And the first one that you lay down you don't have to worry about too much.
I'm just going to press that down so that it's stuck.
And then the next piece that you put down, just be careful to line it up correctly.
There we go.
Just make sure it lines up correctly.
Okay.
Then just use a craft knife to trim it out.
And generally I'll keep the craft knife in one spot.
And move the paper around.
And that will give me the cleanest cut.
And I've just got it sitting right up against the edge.
And I'll remove it like so.
Do the same with the other.
Okay.
And then lastly I'm just going to use a ball tool.
To tap around the centre to just give it a nice hammered metal look.
And that's optional, you can cut out the centre if you want to.
I just think that it looks nice.
And there we are.
Now I'm going to pop them into the oven for about an hour.
Just to make sure that everything's cured.
And then we can finish them off.
Okay.
And here they are out of the oven.
So all I need to do now is just give it a quick buff.
You can also give it a light sand over the top if you feel the need.
I have given this one just a little bit of a sand with a 600 grit wet sandpaper.
And then I'm just going to take a little bit of this wax.
And I'm just going to brush that over the top.
So that when we buff it, it will give it a little bit of a shinier finish.
It's not completely necessary because you don't need to seal anything in.
That metal leaf will be on there quite good.
But it does give it a little bit more of a shine than you would get if you just straight up buffed it.
And I'm using a Dremel.
And this does make a bit of noise so I'd advise turning the sound down if you're wearing earplugs.
I'm still going to continue buffing but I do just want to stop and show you how that looks in comparison.
Okay. And that is pretty much it.
I did drill the hole, popped a bale in and put it on a cord.
But that's pretty much it for the project.
Pretty easy and quite a fun design. It's a bit more on the tribal side.
You could make these a bit smaller and turn them into earrings.
You could also cut out the middle so they're a little bit more light for earrings as this is a bit heavy.
But yeah, you could do that as well.
So anyway, if you enjoyed this tutorial, please do let me know in the comments below.
And if you'd like to support the channel so I can keep doing tutorials just like this one each week,
please do consider becoming a member of the channel.
There is a join button below this video.
There also is a link to Patreon if you would prefer to do that instead if you're interested.
But anything is greatly appreciated.
Thank you for watching and I will see you in the next one. Bye for now.
