Dainty Rings With Beads and Crystals (wire wrapping rings) DIY Rings, Stacking Rings

Exquisite jewelry
18 followers
49 Video Views·Apr 19, 2024
For these dainty rings I'm gonna be using 24 centimeters of 20 gauge bare brass wire to start
with. I'm wrapping it around a cuticle stick right in the middle of the wire and then twisting it.
Once the twisted part is approximately four centimeters I'm going to wrap it around my
wooden ring mandrel to shape it into a ring. Then I cut in the middle of this loop,
slightly bending the long wires out of the way and then gently straightening the two short ends.
I'm going to be using my round nose pliers to make loops and here where my nail is pointing
will be the part I'll be using for all the loops. You can even mark it with a marker pen if you'd
like to. I'm using my fingers to push the wire around the pliers and then I also use chain
nose pliers for a better grip. Next I need to make the loop on the other side and so I push the
pliers through the first loop and repeat the process. Then I cut the excess off and I'm doing
it with the flat side of the wire cutters for a flush cut. Again using my round nose pliers I'm
closing the loops nice and tight. One of the loops is slightly bigger than the other one and so I'm
cutting a tiny bit off. Then I'm repeating the process on the other side. My ring is a bit
deformed and so I'm using chain nose pliers to shape it back into a ring. Next I'm taking 18 centimeters
of 26 gauge wire and choosing a bead. I have all these beautiful tiny gemstone beads and I was going
to use this blue one but then I ended up trying something different. So I have this gorgeous
crystal chain and I'm gonna be using one of the little crystals in setting. Basically need to cut
the link really close to the setting and the same on the other side of the setting. Then drop your
crystal on a table a few times until both pieces of the link come out. I have my setting in the
center of the thin wire and I'm placing it right in the middle and the wires go through in between
the loops. Now I need to sew the setting in place. So I'm taking the end of the wire and pushing it
through both loops to start with and making it nice and tight. This wire needs pushing down a bit
and then I'm tightening the wire again. I'm then taking the end of the wire again creating a little
hook on the end and feeding it through the middle of the loops and then out. I'm also using my chain
nose pliers for a better grip. I'm repeating the same process on the other side to fix the setting
in place. Again making a little hook and feeding the wire in between the loops and then out. And now
I'm going to finish the wrapping on one of the sides. I'm just bending the wire to push it through
the ring band and making it nice and tight under the setting just off to the side. Then pushing the
wire through both loops and again through the ring band and then once more through both loops. Nice
and tight. Then repeating on the other side. I'm cutting the wires short, bending them and then
finding a small hole inside the loops and then pushing them in. And here I'm just pointing at
the ends with my pliers. I hope you can see what they look like. Now this ring is almost finished.
As you can see the setting spins a bit when it's not on a finger because it only has two holes.
It's fine by me but if you mind then you could go around the setting with your wire in different
directions possibly even right underneath the setting to keep it in place. Or you can use a
bead instead which is what the initial idea was for this ring. I love the look of this ring but
I'm gonna take it to the next level. As you can see I made it very small and that is because I
intended to hammer it afterwards and that's what I'm going to do now. There are so many different
types of hammers and I have loads too but for this one I'm gonna be using this dome face
jeweler's hammer and also this ball heen hammer. I'm using the dome face first and texturing the
ring band. It's nice and smooth so it will not scratch the metal. The wires will expand in size
and I will end up with a ring about two sizes bigger once I finish which is what I want. Next
I'm going in with a small ball hammer when it gets too close to the loops since I want to be
more precise and not hammer the loops or my setting by accident. All done. The loops on one
side have moved slightly and I'm just fixing them back in place. Then I'm gonna give my ring a quick
polish with my polishing cloth, wash it in soapy water and it's all done. I've noticed the wires
were a bit too low and so I pushed them up a bit with my chain nose pliers and now it's finished
and what a gorgeous ring it is. I'll show you a few more rings I made using the same or similar
technique in a minute. For now let's enjoy the look of this little beauty. I have also made this
ring with a Swarovski pearl bead and I love it. It's so dainty and just beautiful and this one
has been made with the tiny gemstone beads I showed you at the beginning. I used three of them
but once I had them fitted on I've noticed one of them was a bit uneven. I guess I will need to pay
more attention to details in my future projects. And this last one was the very first ring I made
quite some time ago actually. You can see this gemstone bead sits more on the top of the loops
rather than in between them and I have wrapped the ring around in a slightly different way as well.
This will make the ring more secure but also more robust and less aesthetically pleasing in my
opinion. So I prefer the other way of wrapping the wire. It's also a bit higher than the other rings
so less practical but I wanted to show you anyway. I wonder if you have a favorite. I think mine is
the one with a pearl. It's simple and sophisticated. If you have enjoyed this video then please give it
a like and subscribe to my channel for more videos on easy jewelry making and other projects.
Have a beautiful day and I will see you next week. Bye!
