可摺疊的手機包製作教程,製作簡單夾層多,一起來DIY一個吧 手工布藝 #DIY快樂手工

DIY快乐手工
7粉絲
我是手工愛好者,分享各種布藝作品的製作過程,複雜的布藝簡單的做。真心希望視頻可以幫到大家,也希望大家來訂閱我的YouTube頻道,歡迎大家點贊、分享和評論。謝謝大家支持!本人在在頭條和百度也有相同名稱的頻道。
微信公眾號為:DIY快樂手工
淘寶店鋪:DIY快樂手工
來去縫,分緝縫,包邊縫:https://youtu.be/AuKWUXlMECU
怎麼車縫好拉鏈:https://youtu.be/VeL_2M08j4c
怎麼選做包的拉鏈:https://youtu.be/RX8EpWkUQVA
怎麼熨燙鋪棉不起泡:https://youtu.be/TYUbZuNe6W4
怎麼選鋪棉:https://youtu.be/2jEYFRDaaN0
怎麼選按扣、氣眼、鉚釘:https://youtu.be/2dupt-hg7j8
怎麼包邊:https://youtu.be/20Q6Icz8Xg4
#DIY快樂手工
Hello
everyone
welcome to Happy Handicraft
Today we are going to make a mobile phone bag
It is characterized by many pockets
There are 123456 pockets in the mobile phone bag
We can put the mobile phone in the middle pocket
It's pretty good
Next
let's see how it is made
First of all, let's make a pocket for the mobile phone.
This piece of material is 32
centimeters long and 16 centimeters high.
We fold the material
in half and sew on these three raw edges,
leaving a return opening in the middle.
After turning to the front
we sew three lines
First
we put a piece of webbing in the return opening and sew a narrow edge
Then we fold in three centimeters on both sides of the material and sew a narrow edge of 2 millimeters on each side
Next
I will introduce the main material to you
Our four pieces of material are 32 centimeters long and 20 centimeters high
One of them is covered with cotton
which is one centimeter less than the fabric
Now let's take out the pocket material we just made
fold the three centimeters we measured here in half
and then iron it to death
It's the same here
We put it one centimeter away from the bottom edge
The center line is aligned.
We sew these two sides and
then sew another line at the bottom.
Next, let's cut a few pieces of grid material.
The width of these materials is 10 centimeters,
the height of the large one is 16 centimeters,
the height of the small one is 5 centimeters,
and two zippers 10 centimeters long are also prepared.
We sew them together,
because the grid material is relatively sparse,
so we sew a line on the reverse side,
turn it to the front side and then sew a narrow edge,
and then we fix the grid
material on the top of the main material,
one on each side,
two centimeters down this edge.
After we put it in place
this side is aligned
and then I found a one-centimeter-wide ribbon
and we covered the two raw edges
sewing the two narrow edges here is the same
and we cut off the more on this side
Next we take out the other two main materials
which have not been ironed and laid with cotton
and I have sewn them in the corresponding positions The width
of the male and female paste is 5 cm,
2 cm from this side,
and 2.5 cm above.
We combine this material with what we just did.
The front side and the front side are opposite,
the whole sewing circle is made, and a return opening is left to be turned to the front side.
Next, let's make a bag cover.
These two materials are a square of 10 centimeters,
with a rounded corner at the bottom.
This material is ironed and covered with cotton.
The cotton is one centimeter less.
We fold the two materials together
and then wrap the three edges with the wrapping tape
Next, let's take out the main material for ironing and laying cotton.
Here is three centimeters
below the center line.
We put two D-shaped buttons.
The position of the D-shaped buttons is 2.5
centimeters away from both sides of the center line.
I have this specification of D-shaped buckle and webbing in my window
I'm cutting a webbing
The length of the webbing is 10 centimeters
After we put it on
we sew the whole circle
After the D button is sewn,
let's take out the bag cover we made
before and put it here.
Align the center line
and then take out a piece of the main material,
our front and front are opposite,
and then the male and female
stickers are on this side,
sew a circle,
leave a return here, now I have all the materials ready,
then we sew two groups,
male and female stickers on our bag cover,
sew half a piece,
fold it like this, in this position, we sew another piece.
They are a group.
Then the other group sews one piece on this corner
and then turns this side over
and we sew the other half on this corner
The two of them are a group of male and female sewing
After sewing
we stack the two materials and then sew the three edges
Then we sew two double lines in the middle,
and the width of the double line
is the thickness of the bag after we fold it.
Now I have sewed all the threads that should be sewn
and the bag belt is installed
Let me tell you again that we have two groups of male and female pastes
The bottom here is a group
so that when we carry it on our back
the bottom will not be warped
Here is a group of videos
That's all
Thank you for spending your precious time to watch my videos
Remember to give a like
See you next time
