Lecture 41

IIT Kanpur July 201
20 followers
Mar 17, 2024
[Music]
[Music]
Welcome to lecture three of Gas Power Cycle.
In the last lecture, we had discussed the
gasoline type engine which is built on the basis of spark
emission spark
and its ideal cycle which
is tow cycle. How can
Otter Cycle be promoted? Otter
Cycle consists of four processes.
In this lecture, we will
discuss about Diesel Cycle and
through some examples, we will understand
how it
is solved. So first, Diesel Cycle. Let us know about what was the
difference between this and the gasoline cycle which was called auto cycle, what is the basic difference, of
course, the fuel composition of
both of them is different,
what is petrol in gasoline? It is said that its
molecular weight will be low and diesel which is high molecular weight
but it has another property and that is that
whatever compression we do, in the process of doing it in auto cycle, we
do it up to that level. It
remains below what is called auto-ignition temperature, that is why spark
is used on it so that it can burn and the
same thing is that in the diesel cycle, the compression we will do will be
higher than the temperature which is auto-ignition temperature. This
means that It will auto ignite and it will
burn automatically. There is a
difference between the two and that is
why its cycle is also a little different
because in the diesel cycle it has a
combustion process in which the fuel
is being burnt. It will happen that it is a
little slow, it takes time and that is
why in this and the other case which
we are in spark generation, one has less molecular weight
and hence it goes very fast, so there is
this difference in both of them, because of this it
is fast in that. We say that the
combustion is at constant volume and
here the cycle is in anchor duration, so
we approximate this process at constant pressure,
so the
difference between the two is the rest which is the number of cycles and the
rest which is the number of cycles. The processes are
four processes in one cycle in a cycle and
remain the same, the only change is the
combustion process. In your outer cycle, it is
volume pressure and in diesel cycle, it is
constant pressure pressure. So this is It was invented by Rod Diesel. If
you understand that this
idle cycle was made and it is at
approximate
pressure, then the process of heat addition will
remain at constant pressure in diesel, so
this idle again, we are calling it idle cycle
in this because it The cycle is
idealized, just as we said it is idealized in the auto cycle, similarly it
will be idealized in the diesel cycle, the only difference
is between the auto and the diesel cycle, as I said just
now, the gasoline engine has a
spark plug. This is because the compression of the spark is
below the auto ignition temperature, hence spark is
required for compression, whereas in this
diesel engine, the compression is high,
due to which
it goes above the auto ignition temperature. And it starts
burning on its own, so this is the
difference between the two. Now if you understand it in this form
which we call the form of process diagram,
then like I said in the diesel cycle, the
number of processes will
remain the same. For example, there will be only one difference in the auto cycle,
which is heat addition, where there is
compression, where there is combustion, whatever process
we call, we will call it heat addition,
as we also said in the auto cycle, so
that part is your constant. There will be
constant volume under pressure, not volume.
Remember the auto cycle which was and it was like this
that your
isotropic compression is happening, okay from one to two, heat is
constant volume, heat addition is happening, then
comes your
entropic expansion,
then th to four again. Four to one comes
heat which is rejection which means the exhaust which comes out, so here
your combustion process is taking place,
here your exhaust is coming out
which is called heat rejection, so this was this, this is
auto cycle,
okay, the difference you can see here.
These are two and three, this is your combustion
process, here we are talking about heat addition,
this is what we call heat addition,
look at the tooth which is here, your
constant pressure is here, this is the only difference, the remaining tooth
is this. Compression is done
and tht ph is there is expansion and
4 tov is there is rejection,
so notice what is there, first we
compressed, after compressing it
reached the auto ignition temperature, there
this combustion is taking place, we replaced it. This is the
idealization from constant pressure heat addition, after that, three state
three is reached, from three to four, the
expansion of the volume will be an
entropic process, in which we know that
entropy is internally reversible and
is additive, after that four. Se one which is your
heat rejection is heat constant
volume, you can also write it in TS form
like we did in auto also, the only
difference is that if it does not break then it
will remain the same constant tropy p tooth which is your
pressure ill too. Will remain constant, which is heat
addition term, two again, constant
amp, four, two, which is constant volume,
remember,
in the case of auto, all this is true, the only thing is that
here, whatever is constant, this is also
constant. Just
remember this was in the auto case, it's
fine. Let's
analyze this diagram.
Pay attention to it, the heat addition which is between the hat tooth
and the heat reduction which is between fo two and
if I have to figure it out, then you have ta
equal to two. For example, if you want to calculate its E, then that of
Diesel, you will
have double net Eq in, which we can write as 1
- q out by q
in, ok based on total energy, so
according to this, you will get this q out and q in which is the
state. You should know how to calculate property between property 41 and 23.
So let us see
how to calculate it. Another important thing in a diesel cycle is to
remember that we
call it a closed system. It is adline, like
we have taken a closed system in auto cycle also.
Okay, so now let's discuss about the tooth process
so that we will find out
how K in and K out, which is your internal
energy, we will relate it to the process of four and n and two
and th. Okay, so first th key. If we talk about
th then you see th which is your which is
related to why in if balance
in this process why in then balance the energy on
unit mass
then your in minus e in minus e out is equal
to change in change in delta y Which will be your
system energy so e in minus e out e
delta y which will be your u3 minus y2 but we are
doing it according to unit mass but what will be q in
and delta and q out sorry e in
what you say minus e
out E delta e, what will be the e out in this? E
out is yours because this is the pressure, this is a piston
cylinder. Pay attention, why in this, you have
added heat but the
volume is changing in it. Pay attention, if the volume is changing,
then naturally it is a piston cylinder. So the
boundary will move and that too
at a constant pressure, so this is your double will actually
be out.
Okay, we can simplify this,
this is p2 joke constant pressure to pay
is p2 v3 - v2 this is your total w v Out
will be a v3 - v eight OK, this means
that
whatever q is in is
u3 -
u2 + p2 v3 - v2 OK, if I want this then
u3 + p2 v3 because p2
is constant then p2 and if p3 is constant then u3.
Plus p3 v3
minus y2 plus
p2 v2 joke p2 which is your equal to p3
and that's normal whenever y is a constant
process pressure process then you get
why this is what we had discussed earlier also
why you can call change in elp. That's what
I am proving to you here, here
this is your h3, this is your h2, so
this is your h3 - h2 and this idle gas,
we have explained all this, this is the
basic analysis of the idle cycle, it is a standard part. So a3
my s2 we
can write cp3 - t2 okay so this is yours
Q. In the
same way we can write four one which is
constant volume, if the constant volume is
yours then
db out then your will become zero
and meaning k in minus e out on this if
you do the energy balance e in minus e out what is e in e
in is not yours then
0 minus e out what is e out your q
out it will come yours yaw minus u4 so this
Your k is out, your u4 min
yv, this is your cvt 4 min t1, okay,
you will always write y in the form of CV, you t4 my t1, okay now if you want to find out t
and in this we are always using the
basic formula. It will remain the same that cold
standard air will be taken as ajman, meaning CV and
CP will be considered as constants like
room temperature per second. Otherwise, you are being
told that brother, you have to take variable. Okay, it means
variable. This means
that you will have to look at the table. In such a case,
you cannot apply it directly, what
I am doing is that you will
directly look at the table first and from there you will directly extract y and u4
u1 and above q in h h and
h3 my h2 that too you will extract s2 from the table.
You will take out s3 from the table, you will take out from the table,
that is when your
constant CP or CV cannot be taken there,
in that case you will
not take your cold standard Ajman, which is there, you will have it
written in the question, it will be told,
if not told. You can say that take cold
air standard action, it means that you are
directly considering that
your CVT has been fired and C
which is constant in this process which will happen
at room temperature, so now let's calculate it and this is
your double
net.
Na minus k
aut kya in Okay, now I have it already
given na minus k out your
thvi t4 minus t1 and kya in tha c
patti 3 minus t2 it comes to na minus seep
ba cv c ba cv which is
your k And this is 4 my
t1 t3 my
t2 So this is yours and
you can write this and simplify it or you
can do minus ratio of temperature,
normally this ratio is temperature because if they
live side by side then there is no more one. And between four and th and
two you can say this
because this is where your ratio value will be, so
if you want, you can also write it in the form of ratio,
okay in this case
you can take out tee and and this is Gaya,
your t4 bav miv can also be written like this and in
other cases, you can take out the t
from the bracket and you can write y like this. Okay, so in
a way it can be written like this.
Now we can define one more thing in this.
So your eta is here, okay, in this
you see what you have and the ratio which is the
ratio of heat capacity which is your specific heat.
Now after this one more thing we can do
which is one more thing in the diesel cycle. The term used
is cut off radius. Cut off radius is
your ratio of the cylinder volume after and before the combustion
process. So
in this case what we have is RC. If you see then the
combustion process ends which is your
T.P. Okay, so this means that its
jovi
is v3, it is yat, then its ratio
is v3 by v2, this will come out
which is the cut off ratio, so you
can either take the total volume or you can also take the fixed volume. But you
can also take mass, so it is the same
thing, if you use it, okay, then
after this ratio, you can also see what is there,
because this is your ideal gas relation,
you can use it like we have. It has been used earlier also,
we have related v3 and v2 to the
temperature, ratio of
temperatures and K has been used in it,
so those are the number of relations of ideal gas
in such cases in which there are entropic cases,
so if we entropic relations If you
use idle gas then
you can reduce the thermal efficiency
in two forms, first in this you
can use the compression ratio which you
know is this factor, normally your
v1 will be v2 and Secondly, the RCM has
just defined v3 and v2, so
after this the relation that comes out is
this, you can also derive it, but
I am writing directly here,
okay, so what is shown above is okay.
So, the efficiency which is there in this, you
can see that it is completely different from the auto,
this term which is there in it, is multiplied. In the
case of auto, you have seen that the eta which was there
in the case of auto is not minus the
human, so this is the efficiency. Actually, it is
different, in fact, this term which you are seeing,
if you check, it will basically
always come out as greater and smaller, okay,
this means that you are seeing this term which
is graven, it means that
Actually, if seen,
its efficiency is more than auto diesel.
Okay, this is based on this expression. Now if we pay
attention to it, like if
you increase the cut off radius, then the efficiency decreases
or if the cut off radius decreases then the
efficiency. If you increase the radius then its
expression will come out like if you
increased the cut off radius then it is ok then you are seeing
that its efficiency has reduced, ok
if you have increased the cut off radius
then it has increased ok.
If a is fixed on any one a, then this is your condition valid in fix r.
Okay, so if but rc is one,
if rc is one, then this is the expression that is
visible, it becomes one f rc e two.
You can prove that in such a case
if RC becomes one then it becomes thermal
auto and it thermal your diesel becomes the same.
Okay, then this question
arises from you that in such a situation people say that diesel
has more efficiency. It happens that why diesel vehicles are
sold, the practical reason for this is
that the R is there in diesel in which we
saw the ratio and in the case of auto it was here
but in the case of diesel it is here, generally R
is more in diesel engines now. If it
is more then naturally see your expression.
If the compression ratio is more then
it will be more, that is why in your practical
case, the efficiency of the diesel engine is
higher and the
engine runs better because
its compression ratio is higher.
Okay, now that we have understood this, let us
further clarify our
thoughts by questioning it and how
we can use it. Okay, so this
question is on the ideal diesel cycle
and the
compression ratio in it. 18 is given, it means
that r is given
18 which will be your v1 ba v2 and cut off
radius which is given rc is v3 ba
v2 this is given to you ok now at the
beginning of the Compression process means the
condition of air in the beginning is given as
100 kilo pascal and 25 degree Celsius
and
1917 cm K. Now utilizing a cold a
standard we have to use, what does it
mean that CV and all these things, we will
take the constant as room temperature. And
we have to find out what is the temperature and pressure of
off air after each process
and what is the net work output and
what is the thermal efficiency
and what is the mean effective pressure.
Let us understand. How to do it,
okay, so first of all you have to understand what is its
process diagram,
so process
diagram, this is
your supposition,
okay, so this is one, this is two, this is
three, this is four, this is your
entropic
o compression. This isotropic expansion is done,
okay this is your heat in, Q in is okay
and this Q
out is pressure, this is volume. Okay, so
now what have we been given, first of all you
understand this, all these are cold standards in the form of Ajman.
This means that we will take this as a
constant which
is specific
heat at room temperature. We will take it at room temperature.
Okay, and we can get its values
from the table, then its
value will be found out just like the value of an oyster will be found out.
Kelvin CV per kilo joule at 005 kg.
Your
value of K and K at 718 kilo joules is 1.4. Your table
is in A. It is okay and you already know the gas. If
you eat the value of R in the value of K, then
R is Value of
287 kg Kelvin per pascal meter cube,
all these properties come from you,
now what we have to do is that we have to find out the temperature and pressure of
what is happening at every process point,
so what is given to us. That is, the
initial condition which has occurred at the
beginning of the compression process means
that one state one is given information state one is given to
you
19 17 cube is given
Pav is given
100 kilo pascal teve is given It is 27 which
means 300
Kelvin.
Okay, now this information has been given to us
and along with this we have also given that
t vv ba v2 y you have 18 and v3 bavi
which is yours okay let's start
one. So v2 because we know v1,
here v2 will be v1 by 18 which is 19
17 18 cm. This is your
106.5 cm
cube. After that comes your v3 which is now that
you know v2, so what is v3?
From here we will take out v3 which will be times v2
which will
come to 213 okay and what will be v4
v4 will be your v1 so you
know the information about the volume of all the points
now we try to find out the temperature so if the
process to Okay,
so it is an entropic process.
What is the meaning of entropic process that you can write t2 / t1
as v1 ba v2 k -1 because this is
pv2 power k which is its constant,
from this you can extract this relation. We had
derived the relation of idle gas a so
from here you get
t2 which is t1 times v1 times v2
which is v1 / v2 which is nothing but 18 and k gives you 1.4
-1 t1 we know 3 ken toy nikal k
Comes 953
Ken, okay, from here then we
can also find out the pressure p2 which is yours,
similarly like we had the relation of t12 and t1,
similarly there is also the relation of p2 p2 ba pv, this is
your same as v1 ba v2 but it comes in this.
Okay, so from here your P2 will come out,
Pav Tom 18 1.4, which is your nickel,
72k 20 kilo pascal, okay, so Akos p2 and
p1 have come out, now in the same way you
can do the rest of the things too. But a for the sake and
what I have to do for completion, let
me show you this, so one and two which is there,
you have removed the pressure of two and three,
so p3 which is there, now we are removing the third state,
third state through. What is called state three, we are
extracting what is state three,
which will make p3 = p2, right?
Now that this is a constant pressure, it is simple,
we will extract the ideal gas relation, then p3 v3 ba
t3, which is p2 v2
t2, will remain and you will have this. The pressure is that
p2 which is p3 is okay so this this and p3
and p2 so you can cancel so
from here it will come out your t3
which is t2 v3 ba v2 okay v3 and v2 which
are and y which Resh is rc basically so
this is t2 in rc so from here you r s what is
your p so this is 953 so from here your
t3 will come out 1960 kelvin ok so your
p2 p3 is known t3 is known now let's talk.
For the state four key, we will
take 34 processes, which is icepick process,
expansion.
Okay, now we will do the same thing in this, that is,
t4 by t3, which is
b3, will be the second of five and similarly p4 by
p3, which is
Now v3 will be of Bavi, now we
can easily find out what is v3 and v4, why
because you have already worked out the relation of v3, so
we already know all this information, so from here
we can easily find out that. Actually the
same compression will come out which is 21 to two
so this is the fact that I have extracted from here already
know v3 and in this case
f know f is your vv which is
106.5 cm cube
no no vv f vv
is the same so this It will come out to be
917 centimeter cube, so here if you
click here and enter this information, then
this value will come out
t4
t3
213 by
917 centimeter cube and this is also centimeter cube
and it will come out
7 91 k or t3 you will plug in. We will have to do 19
Kelvin is around 1960, so the answer will be
around 91 Kelvin,
similarly you will get pressure from here also p4
which is your
p3 v3 ba
v4 if this is actually K then it will be 1.4 -1, here it will be
1.4. So it comes out to be
264 Kilo
Pascal, so the process is the same, you just have to pay attention
to what we are extracting, pay
continuous attention, like
highlight it well so that
you can see it because you have enough space to use it.
Note that it is
clear,
you have to identify it and
highlight it so that you
can use it well in the future questions. So in this
way
you have got all the temperature pressure. Now
we have to find the network output. And if we want to
calculate the thermal efficiency, then let us move on. For the
net output, the Eta that you have will be
W
net ba k in.
Okay,
so you can either calculate it like this or
I can directly calculate it like this which we
calculated earlier. The relation is this one,
we
can also use this relation, the thing is the same,
if we have to draw a network, then it
is easier for us in this way that we
first draw the dubnet which is In minus k will be
out, okay, so what is in will be
m h3 - h2 which is at constant pressure,
so this will come out of your
end temperature, plug it in a
and the value of a is given, plug us in.
So it will come out to be
0023 kg, so in this way you
can find out Q in, which comes out to be
21.1 36 kilo joules and Q out which is and will come out,
similarly a u4 mine
yaw which will come out to be
MCV t4. If you plug it in then it will
come out at 786 kilojoules and in the same way
your net will come out to be
213
6786 so what will come out is 1.35 kilojoules then
what will come out or your come out will be
1.35
2.16
632 And if you had plugged in 6 at 3.2, then
effectively your relation would have been the same
because you would have had to apply RC, it would have taken 2 r 18, it would have become
1.4 -1, here at -1, it would have come out to be the
same whether you do it like this
or that way. Do it because you have that relation together,
you can do it directly, why you
can do it because you can easily
calculate it in one expression
and because
we used cold air in it, okay, so that's why
we also use this expression. We can use
and the expression should be similar to the
code layer that we had written, and just two more, which was tam. Okay, so
we can use this also directly. Well, the
third question was that
in this, we have to use mean effective pressure. What is
effective pressure? Remember that
this is your MP and your W
net v max which is of the piston v minimum in this
case
v1 is v2, when you plug in the
values will come out to be 746 kilo pascal
ok so this is your The mean effective pressure
came out to be 746 Kilopascal. So,
I hope that through this example you
understood how to use it,
it was simple, in this you did not have to use the table, you
directly got the
relation between heat, specific heat and enthalpy. And
we used the relation of internal energy and
considered it as a constant. CP and CV became
easy for us. We did not have to use the table,
but sometimes the table is easier.
You will get it more quickly. There will be
no need to do calculations.
You can directly Can be extracted from the table if there
is data in the table and there is no need to do interpolation
then I hope you have
understood this. Now in the next lecture we
will take another cycle which will be called Brayton cycle.
See you in the next lecture
[Music]
[ music]
[music]
in
[music]
h
