Fully Automatic Water Level Starter For Your Water Tank. In this video we are going to learn how to do float switch connection with water Pump so that we can turn ON and OFF the Water Pump Automictically on behalf of water Level.
Friends, to fill the water tank in our homes,
we use a single phase pump.
Now
if we want our pump to
start automatically according to the water level. When this happens and it
stops automatically, then for this
we have to install this type of float switch inside the water tank.
Now by
using this float switch,
we can easily turn the pump on and off but
here is the problem. It will happen that
if there is
any kind of problem in our float switch, then
full current will come inside the water, so if you
want that there is no current in your water tank, then
for this you can do this.
Use this type of SSR.
To make it operate,
we have to provide only DC power supply, that is, by
providing DC power supply of 3 volts to 32 volts,
we can start this SSR and
its Through this we can switch on and off the motor,
how will we do it, let me tell you,
look at the present time, I have a
water pump, this water pump is single phase,
so I will have to use an MCB here,
with which MCB I The
power supply of single phase will have to be brought and
connected. Now after switching on this MCB,
we will
get face supply and neutral supply from these two terminals. So,
we will connect two wires on the two terminals of this MCB which are face and neutral.
We will connect these two wires and after taking them, we will take the
phase supply which is our phase supply, which is the
output terminal of the SSR, as
you will see, it is written here that it is output and the terminal
is above the output. We will take the
phase supply wire and
connect it to that terminal. Now
we will get the output power supply of the phase supply connected to this terminal at this point.
When our SSR gets switched on,
then we will connect a wire from this terminal. We will connect it to
our motor and
provide face supply to that motor, that is, what
you do here is just
connect the SSR between the face supply and the full form of SSR
is Solid State Relay. Solid
state relay is a type of device
using which we
can switch on and off any heavy load, that too by using only
low voltage or other type of
power supply
like we currently use DC.
Now you will understand how we will switch on and off the load with AC power supply by providing power supply. For now,
we have provided phase supply to this pump.
Now if we have to run this pump, then we should
also provide neutral power supply to it. If we have to
do this then we will bring this cable, the
neutral power supply wire in this cable
and
connect it with the motor, that means
we will take the power supply of MCB and connect it with the motor. All
we have to do is connect the SSR in the middle
so that we can switch the motor on and off as per
our requirement. Now
after doing so much work, we have to make the connection to switch this SSR on and
off and
as I told you.
To start this SSR, we will have to bring
DC power supply ranging from 3 Volt to 32 Volt and
connect it on these two terminals, for
this I will use a DC MCB here. Please note that
for AC power supply. You have to
use AC MCB and for
DC power supply you have to use DC MCB.
Now this is DC MCB,
we will
connect this MCB with DC power supply, meaning that the
positive side of DC power supply. There
is wire, we connected it at this point
and we connected the negative power supply at this point.
Now this is the MCB. At
this point of this MCB, we will
get positive power supply. At this point, we will
get negative power supply. So, positive and
negative. We will take both the power supplies
and after taking them, we will directly take that
negative power
supply which is our
SSR, which is the negative terminal of that SSR,
meaning that this terminal will connect
it with this terminal. After connecting, you will
see that there is a negative symbol here,
so we have to
provide negative power supply on this terminal, you will
see one more thing here, at present,
I am using only 12 volt DC power
supply here. Now this is
our DC power supply cable, this
cable also has a positive wire, so
we will take it and after taking it, which is
our float switch, the common wire of that float switch, let us
assume that the
blue one is its common. If there is a wire then
we have connected this wire along with that wire.
Now this is the black wire. From this black
wire we will get the output power supply
when our float switch remains downwards
meaning that the wire which contacts NC is this.
So, we will connect one wire to this wire
and after bringing it, we will connect it with the
positive terminal of that SSR which is our SSR, which
means
that the positive power supply will first
go to the float switch and then returning from there to the
Acer.
Now this float switch will provide the signal to start the SSR.
If our float switch
remains downwards, that is, if the water tank
remains empty, then in this condition the SSR will start
and due to its activation, our pump will
start. Now this water tank will go.
If this water tank gets full then the
float switch goes upwards.
If the float switch remains upwards then in this condition there
will be no current flow in this wire due to which Which is our solid
state relay, it will turn off and due to its
turning off, our pump will also turn off, so in this
way we can
connect the float switch using DC power supply
so that which is our pump with AC power
supply. We can easily turn that pump
on and off through the floor switch.