🔧 Pre-purchase DTCs (Original ABS Issues): Before buying our BMW, we faced these minor issues: - 4809AB DSC: Undervoltage in Vehicle - C90060 AUC Sensor: Internal Sensor Fault (Junction-Box Electronics)
🛠️ After Incorrect ABS Installation: The seller promised to fix these but hired an unqualified mechanic. Result? Wrong ABS part used, no system bleed, spongy brakes filled with air!
⚠️ Dashboard Chaos: Post-installation, our BMW's dash lit up like a Christmas tree: - Warnings: Brake system, pedestrian warning limited, pre-collision braking offline, front/rear pad measurements unavailable. - DTC Codes (ABS-related): 1. 4809AB DSC: Undervoltage in the vehicle (intermittent) 2. 480A23 DSC: Control unit encoding fault (permanent) 3. 480ACO DSC: Coding data not for AWD (permanent) 4. D3948E: Vehicle speed signal invalid (intermittent) 5. D39A3E: Signal invalid... 6. D3AC8D DSC Interface: Signal invalid (intermittent) 7. D39B68: No message from brake temp. (intermittent) ... and 20 other codes involving JBE/JBBF, SRS, TRSVC, LHML, LHMR, FZD, KAFAS, IC, FRM, TSGFA.
ICM Issues: 1. 48002C ICM, ACC: Interface DSC (Intermittent) 2. D01B63: Missing message from RPA Tyre (Permanent)
Watch as we dive into this complex repair, showcasing the challenges and solutions in fixing our BMW's ABS system. 🧰🎥
Welcome to Professor's Garage.
We have only had this car for a few days, and there's already a major problem with ABS.
Look, spongy brake.
I want to fix a minor ABS issue, and this is what I got.
See how many lights and warnings, totally insane.
Oh, okay.
Let's take a look.
Health Report.
So, it's all this code, all ABS related.
Long list of issues. Because one component
went south, it triggered all the problems.
So, hopefully, I will be able to find out how to fix it tonight.
So, wish me luck.
For your information, this is a pre-purchase issue that the seller agreed to cover, but
they hired a mechanic who did everything wrong.
The ABS unit is not compatible with the vehicle.
I will show the part numbers of this one compared to the original one; they are different.
Fortunately, I still have the original ABS, so I'm going to swap this out and put in the
original one.
So, hopefully, I will be able to restore this back to normal.
This is the original ABS module, and just by looking at it, we can see how many brake
lines are connected to it, in and out.
So, these are the ones that we have to remove from the module there, and then we'll be able
to put this in.
Also, when you do ABS bleeding, very important to keep a big bottle of brake fluid.
For this vehicle, it's DOT 4, but first, we need to remove the electrical connectors.
Think there's a ledge here; you should pry it up, and then you should be able to remove
it.
And then it's loose, you can remove the connector here, and this is the first thing now disconnected
from the system.
We can take care of the brake lines.
This is I, in size 11, see if we can remove it.
Okay, and brake fluid will come out when we remove it, so it's best to have some towel
in here.
It's leaking fluid.
Take out another one, four output lines going out to the four wheels.
This, and then hopefully, you can see there are two in the back here, the same size, and
then one more.
So, these are small, very small size brake lines, and just like your bleeder, it only
requires a very small torque to tighten them, so I don't think it takes lots of force to
remove them.
So, you should be able to easily remove them.
So now, I'm going to tackle the input lines, and these should be, um, these are size 12,
so that's loosen them counterclockwise, the same on the other side.
This one is a bit tricky because of the space, but I think, with some patience, we should
be able to do it.
Hopefully, the bleeding will be smooth, and then because I'm putting the original equipment
back, so what I hope is that the system will not give me too much trouble 'cause I think
it will recognize the old friend is back, and they will just recognize each other, and
it's a happy world.
So, right now, I think they are loosened and can be removed.
There is actually not too much brake fluid coming out, so which is good news.
Also, when you work with brake fluid, be careful not to get it on the body of your car.
Be super careful.
There's a 10 mm here.
I should have removed it first, the mount for the unit.
10 mm bolt.
Now, you can pull the brake lines out of the way, and then there are actually three mounting
points.
One is tightened by a bolt; you remove the bolt.
The other two are simply rubber grommets that you push into place, and you can just pull
it up, and then you should be able to remove it.
Just be careful with the brake lines, don't kink them.
Thank God.
Also, pay attention to the flares of the brake lines because you don't want to ruin them.
So, for now, I'm going to wrap this in the towel, just make sure I don't drop any brake
fluid onto the car.
I just want to make sure the brake lines are okay, and then I don't damage any connectors.
Commit it as much as I can.
The two units, this is the original unit, and this one is the one that the purchaser
replaced it with, which doesn't work.
Their sizes are very similar, but if you pay attention to the part number, I will highlight
here, but the last few digits are different.
I know this one is original; this one is from another vehicle, which this BMW here doesn't
recognize.
Now, I'm ready to put this back on.
This is the original port from the same vehicle here, and before I put it back, you can examine
the ports, especially make sure they are clean.
Pay attention to the brake lines.
My finger is touching it on the second mounting point.
I feel it, so it should be in place.
Now, I can push it all the way in and then make sure I don't crush anything, and I should
do good.
Okay, so, it looks like everything is in place, indeed.
Yeah, you can also feel it.
I think it should be in place.
So, what I'm going to do now is to put the brake lines back on and hope not to damage
anything.
So, gently put things in place before you set them on.
Okay, very good.
I think this one is making things easier.
Okay.
So, I'm going to first use my fingers to start them on.
This is back on, and hopefully, there's no learning engaged.
I do have scanners that are capable of reprogramming ABS and things like that, but when it comes
to BMW, there's always uncertainty.
We shared this journey, enjoy it.
This tool, I purchased it a while back for this application.
Not bad, it's like a ratchet, but I don't have all sizes.
But this size 12 if fits, which is good in this tight space.
No perfect solution, but you only work with whatever tool that you have, right?
This ABS unit is already very expensive, labor even more so.
If you can do it yourself, you can save lots of money, and perhaps your family will allow
you to add some tools to your toolbox, right?
A good deal.
It's really tight, even to turn with the wrench.
It may already reach the end, or maybe it's cross-threaded.
So, I think, be super careful.
Let's double-check the other ones.
Yeah, of course, you want to press it right, and then turn it.
So, I will let you take a closer look at the unit.
What I was talking about earlier was like this one here.
The threading, it goes in more, very few threads left.
But this one, it stops here, still lots of threads.
That is the way it is.
Double-check that everything is tightened, okay, and that should be it.
Now, before you forget, put this mounting bolt, uh, back on.
Tighten it; it's not going in anywhere again.
Right, off then, brake fluid.
Now that everything is ready, we can put the connector back the way they engaged.
Put them in, and then press it down.
It clicks.
Great, again, make sure all the brake lines are tightened, not super tight.
Moment of truth.
I'm going to start the car, do a check, no leak, which is great.
Master cylinder reservoir, make sure it's topped off.
Again, on the cap, DOT 4, so that is the brake fluid you should use.
So, I'm going to go to ABS bleeding.
Good thing it has BMW.
Okay, so, let's read the instructions together.
Okay, continue.
There is a recommended sequence of doing the bleeding: rear left, front left, and then
front right, rear right.
Jack up the car and put it on the jack stands.
Remove the wheels and follow the procedure to bleed the caliper on each wheel.
Bleeder here, this is my setup.
My adapter fits.
Put some fluid already in there, and we're going to start the bleeding procedure now.
I open the bleeder on the rear left.
Let's continue.
Hear the sound.
Yeah, there's fluid coming out of it.
Uh, it looks quite dirty, I think.
So, the first cycle was done.
Before we move on, let's close the bleeder.
Check for it.
Lots of air.
Continue to bleed until it's clean and free of air bubbles.
Close the bleeder and done with this particular wheel.
The last wheel, it's loose, almost running out of just a little bit.
The last wheel is being bled.
It looks good, and I'll close it off.
Just enough to top it off.
Wow, just a little bit, that will go a long way.
I'll check all joints, pump the brake a few more times.
I don't see any fluid coming out of it, so it will be all good.
All done.
Have a test drive with your most important tools for this job, just in case.
All the codes are clear.
I scanned the system, no more warning lights, and everything looks great.
And most important, the brake is firm.
It's all done for today, and there's more to come on how to maintain a BMW and make
it reliable.
I hope you found this video to be helpful and informative.
Consider giving it a like and subscribing to Professor's Garage.
Stay tuned for more car care and repair content.
If a professor can do it, you can too.
Until next time, may the Lord bless you and grant you peace.