Antique Clock Restoration - The Complete Job - Part 6, Restoring the Dial.

Legacy Conservatory
14 followers
4 Video Views·Jan 10, 2024
"In this series, I will be covering all the work required to restore a nineteenth-century bracket clock. This is part 6 where I cover the process of restoring the dial.
The dial had been subject to a strange previous 'restoration' where it has been polished and silver plated. I corrected this work by stripping the plating, restoring the black wax infill, re-graining,
silvering and lacquering to restore the finish closer to its original look. "
Hello and welcome back to part six of the series on restoring the antique bracket clock.
In this episode I'm dealing with the dial and as you can see here it's in a little bit of a state.
A previous restoration attempt has seen this dial polished which is not something that you
typically see on this type of dial and then silver plated which again is not a surface
finish that is normally used in horology, certainly not on a dial anyway. To redeem
the dial I started by testing the thickness of the plating by using some wet and dry paper on
a wooden block and I just started to work the surface and see how much work it needed to
get through plating and to start touching the surface of the brass. As you can see the surface
of the brass is just starting to show through so it's not going to take too much work to work to
get through the plating. I didn't want to deform the dial whilst working on it so I put it onto
this foam block to help support it and then it was down to the hard work. This is wet and dry
paper used dry on a wooden block to remove the silver finish. Now I didn't want to touch the
brass too much. I was taking care to stop as soon as I hit the brass because I didn't want
to take any more life out of the engraving. The previous restoration had been very invasive to
the engraving in such a way that they had taken quite a layer off and made the engraving a little bit
thin and I didn't want to add to that so I was careful to just remove the silvering and then
as little part of the brass as possible afterwards. So a little bit of a wipe down just to degrease
and then it's over to start correcting the waxing of the numerals. Sometimes it's necessary to
completely remove the wax and start again as it will react and bubble with fresh wax and won't
look good but after doing a little bit of a test I found that it mixed quite well with the
wax that I was using so I was able to just refill on top of the existing wax. Again this saved an
invasive step on the dial. I will always try to minimise my levels of intervention. So topping up
the wax as you can see here I'm just warming up the dial plate and then melting the wax stick
directly onto the plate. It's impossible to not get wax over the edges of the engraving
but it's a good idea to try and minimise it. As you can see I'm sort of following the lines of
engraving I'm not getting it absolutely everywhere because that will save work later
as all of the wax will have to be removed from the surface.
So with the dial waxed it's over to the next stage which is wet and dry paper this time with water
on a wooden block again supporting the dial on the foam block and I'm working the wet and dry paper
and I'm just cutting the surface of the wax. I'm trying not to actually remove brass as I said
earlier I don't want to make the engraving any more shallow than it already is. Now it's impossible
to not touch the brass to a certain extent especially when putting the final straight grain
on which would be the last step but I'm trying to concentrate my efforts on the wax itself.
So with the over spill of the wax removed and the dial straight grained and then degreased
I just warmed it up gently with a hot air gun to liven up the wax and to give it a glossy finish.
Now a good wash and it's over to start the process of silvering the dial. To silver the dial
I'm using a silver and paste which is a silver nitrate solution and this is reacting with the
brass and applying a very thin layer of silver to the surface. This is the traditional method
this is how most lock dials that you're used to seeing a silvered finish on are actually
silvered. Some are solid silver obviously but that obviously is entirely different.
Actually plating in silver like this was when it came in is not the method that is normally
used. It's this method of a very fine thin layer of silver applied by hand like this
that is the traditional way of silvering a clock dial. You can see even in this shot the camera is
picking up the difference between the brass tone of the plain brass and then the silvered
tone to the left hand side of the dial and you can actually see the silvering reaction occur
in real time. I like to go over it a few times just to make sure that I've got a good layer
of silver and that it's all nice and even and there we've got the silvered dial. A very important
stage in between the silvering stage and this stage you're watching now is to make sure that
you give it a really good wash and get rid of all of the old silvering powder so that the
reaction can stop. If there's any leftover silver nitrates sort of sloshing around the back of the
dial or anything then it can cause brown spotting later. So this stage is neutralizing the silvering
reaction and livening up the surface of the silver and sort of blending the silvering together
and it's cream of tartar is the powder that you can see me using and it's cooking grade
cream of tartar and as I say it sort of blends the silver finish and livens it up to a lovely
sharp white silver finish. So another really good wash of the dial and make sure it's really dry
and then it's a few wipes of some clear lacquer to finish and that's the dial restored.
Thank you very much for watching and I'll see you on the next episode.
