noc19-ae02 Lec 10 - Induction System Contd..

IIT Kanpur July 201
20 followers
Dec 4, 2023
[Music]
[Music]
so next is externally driven
superchargers we also call them turbo
supercharges an external type
supercharger compresses air and through
an oil cooler delivers it to the
carburetor fuel air control unit intake
where it is mixed with the fuel now this
air which is compressed by the
compressor is routed through the air
cooler so that the temperature of the
compressed air is lowered since after
compression the temperature of the air
will increase so in order to lower the
temperature the air is routed through
the air cooler now an external type
supercharger is composed of three main
parts compressor and assembly turbine
wheel assembly and a full floating shaft
bearing assembly so the energy of engine
exhaust gases directed against a bucket
wheel or turbine provides power to drive
the external supercharger the turbine
drives an impeller that compresses the
incoming air now this external type
supercharger has got three main parts
one is the compressor assembly you can
see in this picture this is your
compressor assembly second is your
turbine wheel assembly this is your
turbine wheel assembly here and a full
floating shaft bearing assembly and this
is a pole floating shaft so three main
parts compressor turbine and a shaft now
the energy of the engine exhaust gases
so this turbocharger is basically using
the energy of the exhaust gases against
a bucket wheel or turbine this turbine
extracts energy from the exhaust gases
now in this figure you can see this is
this inlet this is the inlet through
which exhaust gases are coming in these
exhaust gases are directed against this
turbine wheel the turbine wheel will
extract the energy of the exhaust gases
and this turbine will drive the
pressure this compressor the compressor
is here this turbine will drive the
compressor since the turbine and the
compressor are on the same shaft and it
is extracting energy from the exhaust
gasses to drive the turbine wheel which
drives the compressor since the turbine
and the compressor are on the same shaft
it is called turbo supercharger or
turbocharger depending on whether it
supercharges the air or merely maintains
sea level pressure now in case if it is
super charging the air then it is called
boost supercharger or if it is merely
maintaining the sea level pressure that
in that case it is called turbocharger
however the supercharger is required to
boost the manifold pressure above 30
inches of work
in case if it is a supercharger then it
is required to boost the manifold
pressure above 30 inches of mercury now
this is called a multi speed
supercharger because the speed of this
compressor is dependent on the speed of
the turbine because they are on the same
shaft and the speed of the turbine is
dependent on the quantity and pressure
of the exhaust gases directed against
the turbine so because of that reason
this is called a multi speed
supercharger the volume of exhaust
directed through the turbine is
determined by the position of the base
gate and the wastegate is operated by a
control in the cockpit now the volume of
exhaust gasses which is directed against
this turbine is controlled by the
position of a base gate we will see what
is the wastegate there is a one kind of
thing which is called a way this gate
and this is operated from a control in
the cockpit so the position of the
wastegate
will determine the quantity of exhaust
gasses being directed towards the
turbine wheel the compressor assembly
consists of impeller diffuser and casing
now this compressor which is used to
compress the air has got three main
parts impeller diffuser and Kasey
the air for the induction system enters
in the center of the compressor now the
air which is to be compressed enters the
center of the compressor you see this is
your compressor and this is your
compressor Inlet now air which is to be
compressed it goes through this opening
there is an opening on this side and the
air which is to be compressed enters the
compressor through this opening you can
see here this is a blue arrow which is
showing compressor Inlet so this is
compressor Inlet and after compression
the air is coming out through this
outlet the air for the induction system
enters in the center of the compressor
casing through a circular opening here
it is picked up by the blades of the
impeller giving it high velocity as it
travels outward towards the diffuser now
the air which is entering the compressor
is picked up by the impeller blades
these impeller blades will give it high
velocity and it travels towards the
diffuser as the air leaves the impeller
the diffuser vanes direct the airflow
and convert the high velocity of air to
high pressure now impeller has picked up
the air it has given at high velocity
and the air from the impeller has is
directed towards the diffuser now this
diffuser vanes
will direct the airflow and will convert
high velocity of air to high pressure
air the turbocharger is basically an
arrangement of a turbine and a
compressor on a common shaft so we have
seen it earlier that the turbocharger it
is an arrangement of a compressor and
turbine this is compressor this is
turbine on the same shaft on the common
shaft the turbine assembly consists of a
base gate wall which regulates the
amount of exhaust gasses directed to the
turbine so in our last slide we have
read that the turbine assembly also has
a wastegate wall which will regulate the
amount of exhaust gasses
being directed to the turbine and
thereby it will regulate the speed of
the rotor turbine and impeller so rotor
is your turbine and impeller since both
are on the same shaft they are rotating
so this wastegate wall is regulating the
speed of the rotor if the base gate is
completely closed all the exhaust gasses
are post through the turbine wheel if
the base gate is partially closed so
corresponding amount of exhaust gas is
directed to the turbine oh and if the
waste gate is fully opened nearly all of
the exhaust gases pass overboard
providing little or no boost so in
general the wastegate if it is
completely closed so in that case all
the exhaust gases will be directed will
be forced to go through the turbine
wheel in case if it is partially closed
wastegate is partially closed then
corresponding amount of exhaust gas is
directed to the turbine the directed
exhaust gases strike the turbine blades
yes we have seen in our earlier slide
also the directed exhaust gasses they
strike the turbine blades and cause the
rotor to rotate the turbine and life
manner the gases are then exhausted
overboard after most of their energy is
extracted so after the turbine has
extracted the energy of the exhaust
gasses that air is sent overboard and
the turbine blades are rotating the
degree of waste gate closing determines
the amount of air pressure boost
obtained from the turbocharger so the
amount of boost which is obtained from
the turbocharger depends on the degree
of wastegate opening or closing we have
discussed this earlier also like after
compression the temperature of the air
increases and to high carburetor air
temperature is not desirable as it may
cause detonation in the cylinders so we
will read in our next chapters
what is detonation but it is not a
desirable characteristic so high
temperature of air in the carburetor
will result in debt
in the cylinders so in order to avoid
that the compressed air is passed
through the air coolers in the figure
you can see there are this turbocharger
unit is a split you can see this is your
compressor housing this is your
compressor impeller here this is your
Center housing this is turbine and this
is your turbine housing then again this
is your shaft where it is to be
lubricated and this complete thing is
your turbocharger assembly now
normalizer
turbocharger what is a normalizer
turbocharger the normalizing
turbocharger is externally driven
powered by the energy of exhaust gases
now this is also powered by the energy
of exhaust gases and it is externally
driven these systems are not designed
boost manifold pressure above 30 inches
of mercury rather they only compensate
for the power lost due to the pressure
drop resulting from increased altitude
as we know that as we go up you fly high
your pressure drops resulting in engine
power loss so in order to compensate for
that power loss we need a system which
can boost the manifold pressure the
normalizer
turbocharger system this will not boost
the manifold pressure above 30 inches of
mercury but it will only compensate for
whatever power has been lost due to
pressure drop from increased altitude so
it will just try to maintain your
sea-level pressure they are designed to
be operated only above a certain
altitude
so these normalizer turbochargers you
cannot operate them right from the
ground or from the sea level but they
can be operated only above a certain
altitude since maximum power without
normalizing is available below that
altitude now coming to ground boosted
turbocharger system what is a ground
boosted turbocharger system we have just
seen a normalised turbocharger where it
was just trying to maintain the sea
level pressure it was not boosting the
manifold pressure about thirty inches of
mercury but in case if we want to have a
system which can supercharged with more
thirty inches of mercury in that case it
will be a turbosupercharger system and
they are called ground booster
turbosupercharger system turbo
supercharged systems are designed to
operate from sea level up to their
critical altitude and are called ground
boosted sea level turbocharger system
and are called ground boosted or sea
level turbo supercharger system what as
a critical altitude critical altitude is
defined as the altitude above which a
particular engine supercharger
combination will no longer deliver full
power engines equipped with turbo
supercharger system develop more power
at sea level then engines without both
super charging these engines are also
called
sea level boosted engines in a
turbosupercharger air induction system
the ram air enters the system through an
inlet on the side of the nestled now you
can see the figure here this is your
side of the engine side of the nestled
or side of the cowling and your ram air
is coming through this Inlet you can see
these yellow arrows now your air is
coming through this thing through the
inlet opening now after coming through
this Inlet the air passes through our
filter you can see here this is your
filter and after filter you get a
filtered air ram filtered air you are
getting the serum filtered air passes
through the turbosupercharger see this
ram filtered air is passing through the
turbosupercharger after passing through
the turbosupercharger the air gets
compressed the air you can see this
compressed air is going to the
carburetor or the fuel injector from the
fuel injector or the carburetor the air
you can see here is routed to different
cylinders the air is routed to different
cylinders in case if the induction air
filter becomes clocked then alternate
air or heated engine compartment air
enters the induction system
compressor suction through an alternate
air door within that nestled we have
read about this in our earlier slides
about the alternate air door so again
this is being repeated again like in
case if the filter gets clocked the air
comes to the alternate your door within
the Nessun the alternate air door can be
operated automatically or it can be
operated manually we have read about
this earlier the turbocharger is
controlled by the waste gate and the
wastegate actuator now here you can see
in the figure this is your turbocharger
on the turbocharger you have a waste
gate this is your waste gate see this is
your waste gate and this is your
wastegate actuator so the waste gate the
waste gate will regulate the quantity
the amount of exhaust gas being driven
to the turbine so the turbocharger is
controlled by the waste gate and the
wastegate actuator the position of the
waste gate butterfly wall is controlled
by the wastegate actuator now this waste
gate wall this position its position is
controlled by this actuator wastegate
actuator the wastegate actuator is
connected to the wastegate butterfly
ball with my mechanical linkage so both
the actuator and the wall they are
connected by to each other by mechanical
linkage and the wastegate actuator will
control the position of the wastegate
butterfly ball so which gate will bypass
the engine exhaust gas around the
turbocharger turbine Inlet the speed of
the compressor and the amount of intake
boost is controlled by controlling the
amount of exhaust gases that pass
through the turbine of the turbocharger
now since the amount of exhaust gas
which is passing through the turbine is
controlled by the position of the
wastegate wall this is controlling
the speed of the compressor and finally
the amount of boost being created by the
turbocharger now engine oil from the
engine oil system is used to lubricate
the turbocharger now since you have the
rotating parts in the turbocharger it
needs lubrication so that lubricating
oil is from the engine oil system agent
oil is also used to cool and lubricate
the bearings that support the compressor
and turbine in the turbocharger so
lubrication is one requirement and the
engine oil will also cool and lubricate
the bearings that support the compressor
and the turbine in the turbocharger the
oil inlet line to the turbocharger is
from the oil cooler rather I will say
that the oil inlet line from the
turbocharger is from the oil pump and
oil return line from the turbocharger is
to the oil scavenge pump
now this turbocharger this will have two
lines oil inlet line and one oil outlet
line the oil inlet line in the oil inlet
line which is coming to the turbocharger
is from the oil pump
from the oil pump it is being routed
through the oil cooler and comes to the
turbocharger the oil which is going out
of the turbocharger is going to the
scavenge pump to the oil scavenge pump
and finally from the scavenge pump it is
sent back to the oil tank we have read
in the lubrication chapter the purpose
of the scavenge pump there is also one
which I call in the oil supply line
which prevents oil from draining into
the turbocharger while the engine is not
operating so at the time when your
engine is not operating this check hole
will prevent oil from draining into the
turbocharger so oil seals on the
compressor turbine wheel shaft will
prevent the lubricating oil from
entering the turbine and the compare
housing the oil pressure in the
wastegate actuator controls the position
of the wastegate we have seen that there
is a wastegate actuator and there is a
wastegate wall butterfly ball the
wastegate actuator controls the position
of the wastegate butterfly ball but how
does it control now the oil pressure is
coming to the wastegate actuator which
controls the position of the waste key
there are controllers which provide the
correct pressure in the wastegate
actuator now the oil which is coming to
the wastegate actuator that pressure is
controlled by the controllers these
controllers they'll either restrict the
oil flow or allow the oil to return to
the engine so now two cases in case if
oil is restricted more oil is restricted
then there will be more pressure in the
wastegate actuator so if the controller
restricts more oil then there will be
more pressure and due to the more
pressure in the wastegate actuator the
wastegate will close more more closing
of the wastegate
causes more exhaust gases to pass
through the turbine which results in
increasing the speed of the compressor
and then finally raising the inlet
pressure or you get more boost another
case in case if all is not restricted
then reverse will happen and you will
have a reduced boost pressure so the
controllers they are restricting the oil
flow or they are not restricting the oil
flow to the actuator which finally
controls the position of the wastegate
another example of ground booster
turbosupercharger system or a sea-level
booster turbo supercharger system the
following components regulate the system
automatically so in this system this is
there is there is an automatic control
you have exhaust
I pass bulb assembly then you have a
density controller and you have a
differential pressure controller so let
us see the figure you have this engine
exhaust gases these engine exhaust gases
they are coming to the turbine to the
turbocharger and from the turbocharger
these gases rather these compressed
gases they go to your cylinder intake so
you see here here is being compressed
this exhaust gas has entered the
turbocharger from the turbocharger it
goes to the cylinder intake after
compression now constant power output is
bent eight
if the wastegate position at fully open
and closed and between these two
extremes is regulated now in case if the
position of the wastegate
is regulated at the extreme positions
that is the full open position or the
full closed position and also in between
these two positions these two extreme
positions in case if we are able to
regulate the position of the base gate
in that case we will be getting a
constant power output from the system if
the wastegate is completely closed all
the exhaust gases are forced through the
turbine wheel and maximum supercharging
is achieved so we have seen this earlier
in case if the base gate is completely
closed then we get more exhaust gases
through the turbine wheel and we get
maximum supercharging if the base gate
is fully open nearly all the exhaust
gases pass over world providing little
or no boost if the base gate is
partially closed a corresponding amount
of exhaust gas is directed to the
turbine and constant power output is
achieved below the maximum altitude at
which the system is designed to operate
now in case if the base gate is
partially closed that as it is in
between the two extreme positions in
case that corresponding amount of
exhaust gas is directed to the turbine
and we get constant power output below
the maximum altitude for which the
system is designed to operate in order
to maintain the pre-selected manifold
pressure setting the wastegate is almost
fully open at sea level and continues to
move towards the closed position as the
aircraft climbs now when we are at the
sea level your waste gate is almost
fully open and as the aircraft starts
climbing in that case your waste gate
starts moving to the closed position as
the aircraft climbs so we have seen in
our earlier slides that the engine oil
pressure is controlling the position of
the wastegate wall the engine oil
pressure which is acting on a piston in
the wastegate assembly controls the
position of the waste gate for engine
output power increases when oil pressure
is increased on the westin causing the
wastegate wall to move towards the
closed position so we have seen this
earlier your output power your engine
output power will increase when your oil
pressure is increased agent output power
will decrease when your oil pressure is
decreased on the piston causing the
wastegate wall to move towards the open
position now the oil pressure how is the
oil pressure controlled the engine oil
pressure is controlled by the oil which
is bled back to the engine crankcase now
the oil which is bled back to the engine
crankcase that will control the engine
oil pressure applied to the top of
piston attached to the wastegate warp so
this oil which is bled back to the
engine crankcase will control the engine
oil pressure which is applied to the
wastegate wall the quantity of oil
returned to the engine cranking is
controlled by two independent control
devices one is your density controller
and another is your differential
pressure controller so here in the
figure you can see you
have a density controller this is your
density controller here you have a
differential pressure controller so
these two units they will regulate the
bleed oil so in the figure you can see
here you have the engine oil pressure
Inlet your engine oil is coming here
from this side that is going to the
wastegate actuator so this is here it is
your engine oil from this line your
engine oil is returning back this engine
oil is returning back to the crankcase
this is your crankcase area here so
engine oil is returning back to the
crankcase now the quantity of injured
oil which is bled back to the crankcase
is controlled by the two controllers one
is your density controller and another
is your differential pressure controller
and the oil which is bled back to the
crankcase this controls the engine oil
pressure being applied to the top of the
piston attached to the base gate wall so
basically the oil which is being bled to
the crankcase controls the oil pressure
acting on the piston of the wastegate
wall and this return oil is controlled
by two controllers one is the density
controller and another is your
differential pressure controller the
density controller regulates bleed oil
only at the full throttle position so
this density controller this regulates
the bleed all only at the full throttle
position inside the density controller
are our dry nitrogen filled pressure and
temperature sensing bellows so inside
the density controller you have bellows
which are filled with dried dry nitrogen
these are pressure and temperature
sensing bellows and these bellows react
to pressure and temperature changes
between the fuel injector inlet and the
turbocharger compressor the bellows
maintained
constant density by allowing the
pressure to increase as the temperature
increases so as the temperature
increases it will cause the pressure to
increase and will maintain the constant
density now due to the movement of the
bellows inside the density controller
the bleed wall repositions it and it
causes the bleed oil quantity to change
which changes the oil pressure on top of
the wastegate piston the differential
pressure controller functions during all
positions of the wastegate ball other
than the full open position so this
density controller this is operating
only at full throttle position whereas
your differential pressure controller
operates at all positions except the
full throttle position where your
density controller is operating the
density controller and differential
pressure controller operate
independently to control turbocharger
operation at all positions of the
throttle so these two controllers they
are operating independently at all
positions of the throttle so this was
about an automatically controlled
turbocharger system although the
internal functioning of this system was
beyond the scope of this course but just
to give a brief idea we have discussed
about the controllers the density
controllers the inside mechanism of the
density controller so we have seen what
is the turbocharger what is the
supercharger what is the purpose of
these turbochargers now there may be
problems there may be snags we may
encounter in the system so let us see
what are the troubles what are the
common troubles encountered in this
system first problem may be that the
aircraft fails to reach critical
altitude we have seen what is the
critical altitude so let us see in case
if you encounter a problem that your
aircraft is not reaching the critical
altitude and what may be the probable
reasons so another probable cause
whiskey
is not closing fully and malfunctioning
of controller so we will see in in the
below columns that what will be the
rectification action for that so in case
you have trouble that aircraft is not
reaching your critical altitude we have
seen the probable causes damage
compressor or turbine wheel you have to
replace the turbocharger exhaust system
leaks you have to repair the leaks and
faulty turbocharger bearings you have to
replace the turbocharger now whether
your wastegate is not closing fully in
that case what will be the probable
cause ways Gate bypass small bearing is
tight that may be the reason oil inlet
or FS blocked your oil which is Inlet
orifice is blocked differential
controller malfunction and broken ways
gate linkage so this gate is not fully
closing there may be several reasons you
know let us see one by one you are waste
gate bypass ball bearing is tight
nothing can be done we just have to
replace the bypass valve so oil Inlet or
if is blocked in that case you have to
clean the orifice broken waste gauged
waste gate linkage now in case if the
linkage is broken then we have to
replace the linkage and adjust the waste
gate for proper opening and closing then
now in case if the differential
controller is malfunctioning then we
have several reasons
seals leaking in that case you have to
replace the controller there from broken
you have to replace the controller and
controller wall stuck in that case also
you have to replace the control so in
the in case if you have encountered a
problem where aircraft is not reaching
your critical altitude and the reason is
that your controller is malfunctioning
in that case you have to replace the
controller then another problem that
might be encountered as engine surges
then again there are several reason one
is bootstrapping and
then you may have wastegate malfunction
and you may have controller malfunction
so in case of bootstrapping you ensure
that the engine is being operated in the
proper range so we have to ensure that
engine is operating in the proper range
in case of controller malfunction we
have seen that we have to replace the
controller in case of wastegate
malfunctioning we have seen the several
reasons and the rectification actions
another is density controller
malfunctioning again there may be
several reasons seals leaking bellows
damaged wall stuck in all the cases we
just have to replace the controller so
in most of the cases in case if your
wastegate is malfunctioning your
controllers are malfunctioning we just
have to replace the controllers and the
base gate malfunctioning we can either
check the linkage if case in case if the
linkage is broken we can repair it we
can adjust the opening and closing of
the wastegate
now what are the different inspections
and maintenance on the induction system
so let us see there are a few
inspections which are done on the
induction system the induction system
should be checked for the following
during all regularly scheduled engine
inspection so during all inspections
polling should be checked
cracks and leaks there might be cracks
and leaks in various parts of the
induction system there might be leaks so
we need to verify that there are no
cracks no leaks during the inspections
security of mounting of all the units of
the system so all the units of the
system they should be secured properly
they should be mounted properly
cleanliness at all times so this is very
important the induction system should be
cleaned at all times we need to be very
careful about the filter the induction
air filter and it should be cleaned
regularly so any obstruction
again there should be no obstruction in
the system replacement and cleaning of
air filters so air filters they are to
be cleaned regularly and they are
replaced after a fixed interval of time
so clean air filters are also very
important alternate air dose and
transition ducts we need to verify that
the alternate air dose are free to move
there is no obstruction there is no
breakage and all the ducts they are leak
proof they are mounted properly on the
turbocharger unit we need to verify
secured mounting we need to verify
leakage and we need to see the linkage
is not broken the linkage between the
wastegate wall and the wastegate
actuator is not broken the wastegate
wall is free to move and it is also to
be lubricated at fixed interval then
phase get free movement and duplication
so these are some of the points which we
verify during our inspections some of
the maintenance actions which we perform
on the induction system now there are a
few problems which may encounter in our
induction system we have seen the
problems what we encounter in the
turbocharger now these are the problems
which we encounter in the induction
system the first problem you may see
that your engine fails to start now in
case if the agent is not starting what
may be the probable causes your
induction system might be obstructed
number two there might be air leaks in
the system now in case if your induction
system is obstructed so we need to check
your a scoop and the air ducts in case
if there is any obstruction we need to
remove it that should that will be the
corrective action in case
there are air leaks the air leaks might
be at the carburetor mounting and intake
pipes so we need to check the carburetor
mountings and also the intake pipes so
small amount of air leakage will also
not start the engine so in case if there
are leakages you have to tighten the
carburetor and repair or replace the
intake pipe circuit problem might be
engine is running rough in case if your
engine is running rough there might be
several reasons it may be loose
air ducts may be leaking intake pipes
your engine valves sticking bent or worn
wall push rods so several reasons let us
see one by one loose air ducts in case
if the ducts are loose if the air ducts
are loose then we need to inspect these
ducts and tighten the leaking intake
pipes now in case if your pipes or
intake pipes are leaking then we need to
check the intake pipe packing nuts and
tighten them basically in case if they
might be loose we need to tighten them
engine walls are sticking now in case if
the engine walls are sticking then we
need to remove the rocker arm cover and
check the valve action the corrective
action will be to lubricate and free the
sticking bolts bent or worn wall push
rods in case if the push rods the wall
push rods are bent or worn then we need
to inspect them and replace the worn or
damaged push rods another problem might
be low power in case if we are seeing
low power then the causes may be
restricted intake duct second may be
broken door in carburetor air valve and
dirty air filter so in case if the
reason is restricted intake duct
we need to examine the intake duct and
remove any restriction if the reason is
broken door in carburetor air valve in
that case we need to first inspect the
air valve and replace it in case if we
find it defective if your air filter is
dirty we need to inspect as the case may
be so we may clean the air filter or in
case if required we can also replace the
air filter another problem that we may
paces engine idles improperly there are
several reasons one is shrunken intake
packing another is hole in intake pipe
or another reason might be loose
carburetor mounting so it case if your
intake packing is shrunk in that case we
need to inspect that packing for proper
fit and replace if it is defective
now if there is a hole in the intake
pipe we need to person inspect the
intake pipe and replace in case if it is
found defective carburetor mounting is
loose in that case we just need to
tighten the mounting bolts first we need
to check whether it is loose the bolts
are loose in case if they are found
loose we have to tighten them so we have
seen about the induction system we have
seen about the not naturally aspirated
engines we have seen about the
supercharged engines we have read about
the turbochargers we have read about the
problems being encountered in the
induction system and what are the
inspection and maintenance required in
the induction system thank you
[Music]
[Music]
[Music]
