To access the translated content: 1. The translated content of this course is available in regional languages. For details please visit https://nptel.ac.in/translation The video course content can be accessed in the form of regional language text transcripts, books which can be accessed under downloads of each course, subtitles in the video and Video Text Track below the video. Your feedback is highly appreciated. Kindly fill this form https://forms.gle/XFZhSnHsCLML2LXA6 2. Regional language subtitles available for this course To watch the subtitles in regional languages: 1. Click on the lecture under Course Details. 2. Play the video. 3. Now click on the Settings icon and a list of features will display 4. From that select the option Subtitles/CC. 5. Now select the Language from the available languages to read the subtitle in the regional language.
[Music]
[Music]
good morning welcome back to the next
part of the lecture on Bose processing
concerns so next concern is surface
texture improvement surface texture or
surface finish improvement additive
meant for two parts have common surface
structure features that may need to be
modified for a static or performance
reasons the common surface textures are
stray steps power raishin fill patterns
from extrusion or beam based systems
witness marks from support material
removal so these need to be addressed
staircase effect that I discussed this
is a fundamental issue in their layered
manufacturing and it is difficult to
overcome sometimes although one can
choose a thin layer thickness to
minimize the error at the expense of
build time
the thinner the layer is the more is the
time but we'll have a better finish in
that case but it is better to optimize
the cost with respect to time and the
quality next is powder addition
polarization is also fundamental a
statistic of binder printing powder were
fusion and powder based beam deposition
processes powder has an addition and
that also creates a texture specifically
on the surface typical surface roughness
which is taken from research are like
these four SLA the showed the minimum
layer thickness as 0.1 millimeter
roughness for a grade from 2 to 40
micrometers and for selective laser
sintering it was point 1 to 5 and this
was from 5 to 35 and fro FDM it was the
minimum layer thickness was 0.25 4 and
surface roughness was nine to forty
micrometers for 3d printing minimum
thickness was point one seven five and
the surface toughness was 12 to 27
micrometers we can see that in these
processes the minimum thickness that is
obtained there is in SLA and poly
jetting processes and the minimum
surface Ethne that is possible
here is for SLA and Polly jetting again
so this is a research way back in 2002
15 years or 17 years later than this
there's certain material which are
developed and which can take their
opinion fracturing minimum layer
thickness 2.0 one millimeter and the
roughness that we can obtain is zero
point 2 micrometer so this is thus
present status of the technology the
amount of powdered Hessian can be
controlled to some degree by changing
the part orientation boredom of ology
and thermal control technique the type
of post-processing utilized for surface
texture improvements is dependent upon
the desired surface finish outcome if
meta surface finish is desired a simple
bead blasting of surface can help even
the surface structure removes up corners
from the stair stepping and given
overall meta appearance that is for meta
penis but if polish or glossy appearance
is required then the smooth and polished
finish has to be got then wet and dry
standing and hand polishing are to be
performed so it all depends to what
extent do we need referred surface
finishing in many cases it is desirable
to paint the surface to improve the
surface texture for example with the
sino acrylate
or a sealant prior to sending or
polishing painting the surface has the
dual benefit of sealing the porosity by
viscous forces smoothing the stair-step
effect and thus making sending and
polishing easier and more effective so
this is the use of painting several
automatic techniques have been explored
for surface texture improvement two of
the most common tutelage include the
tumbling for external features okay
abrasive flow machining for primarily
internal features abrasive flow is when
internal features are to be
finished then abrasive flow machining
can help to use abrasive to get the
surface finish that is required
tumbling when external feature is
required the material is kept into a
tumbler and that is rotated and the
powder improves the surface texture so
that is one of the vs next is accuracy
improvements there is a wide range of
accuracy capabilities in additive
manufacturing some processes are capable
of sub mikan tolerances whereas other
have accuracies around 1mm typically
larger the build volume and faster the
build speed the watch the accuracy for a
particular process so bigger the volume
and faster the speed speed and volume if
they are high this implies accuracy is
low so this is particularly noticeable
for instance in beam deposition
processes where the slowest and the most
accurate beam deposition processes have
accuracy is approaching a few microns
whereas the large bulk deposition
machines have accuracy of several
millimeters so these accuracies can also
be seen here the minimum layer thickness
and surface roughness that is obtained
the minimum layer thickness implies the
better surface roughness now for
accuracy improvements we need to know
what are the error sources process
dependent errors affect the accuracy of
XY plane differently from the z-axis
accuracy these errors come from
positioning and indexing limitations of
the specific machine architectures for
instance are we using 2.5 d machines 2.5
axis or 3 axes or 4 axis which kind of
processing which kind of stage are we
using to get the reprimand fractured
part so it all depends upon the
orientation or on the indexing
limitations of this specific machine
stage or machine bed that is used then
lack of closed-loop process monitoring
and control strategies there can also
lead to errors and issues fundamental to
volumetric rate of material addition
such as melt pool or droplet size other
other factors future accuracy
improvements in additive manufacturing
will require fully automatic real-time
control strategies to monitor and
control the process rather than the need
to rely on expert operators as a
feedback mechanism fully automatic and
real-time accuracies I will discuss in
rapid product development module of this
course now Internet of Things is also
there people can just order the product
at their home and a product the specific
customized product the shape and that
can be printed and delivered to them so
those things are there so we need not to
have an expert operators the computers
would walk by itself and the product
would be manufactured so there are
certain interfaces which I developed for
this the material dependent phenomena
also plays a role in accuracy including
shrinkage and residual stress induced
Distortion now integration of additive
plus subtractive processes is one of the
ways we do some additive and done some
some subtractive processes now this can
be one of the ways to have better
accuracy improvements to recall accuracy
is the closeness to the original results
for instance if I need this size as
exactly 20 mm and I am exactly getting
20 mm that is accurate but there are
certain tolerances for instance 20 mm is
my final build I required the diameter
and I am getting something like twenty
point two or 19.8 so this means it has
20 plus minus 0.2 and 0.2 tolerance so
this is
the closer to the final desired output
the higher is accuracy generally
precision is there but accuracy is not
there precision is for instance if i
getting 19.7 19.8 19.7 19.8 it is close
to nineteen point seven five so this
means the part is give us a precise
reading which are close to twenty point
seven five but there's always a
difference of 0.2 to 0.3 mm in the
negative direction so this is precision
so accuracy material dependent phenomena
also play a role in accuracy including
shrinkage and a zero stresses repeatable
shrinkage and distortion can be
compensated by a scaling of the cad
model however predictive capabilities at
present are not accurate enough to fully
understand and compensate for variation
in shrinkage and residual stresses as in
casting we know there's certain
alliances shrinkage alliance then we
have draft alliance though those
alliances are also to be put here
quantitative understanding of the
effects of the process parameters build
style part orientation support
structures and other factors on the
magnitude of shrinkage residual stresses
and distortion is necessary to enhance
these predictive capabilities for parts
which require higher degree of accuracy
extra material must be added this extra
material can be a thin layer throughout
the part or the portions where we know
that high sinkage would happen so that
extra material has to be added that can
be machined again that can machine off
the major build this extra material must
be at which is a critical feature which
is then removed by our other subtractive
means to get a desired accuracy so next
after error sources you have model
pre-processing as the way to accuracy
improvement model P processing is for
many data manufacturing processes the
position of the part within the build
chamber and the Orion
and will influence the part accuracy
surfaced finished and bill time thus
translation and rotation operations are
applied to the original model to
optimize the part position and
orientation so shrinkage often occurs
during a diamond structure
shrinkage also occurs during post
process furnace preparations needed for
indirect processing of metal or ceramic
green parts so these need to be seen in
the model pre-processing step only the
pre process manipulation of the STL
model will allow to scale a factor to be
used to compensate the average shrinkage
of the process so we are essentially
talking here about see a computer-aided
engineering where we see what could be
the shrinkage and when we need to
compensate this shrinkage there would be
always some features which will shrink
slightly more or less than the average
sinkage so we need to see where the
shrinkage is larger and on the other
hand where the shrinkage is low or we
need to work according to that the
specific factors can be taken what scale
factor or what extra material should be
billed accordingly in order to
compensate for shrinkage variation if
the highest shrinkage value is used then
ribs and similar features will always be
at least as big as the desired chama
tree so this is important to have the
segregated shrinkage factors for
instance if they are ribs like we say
the bicycle wheel is their bicycle way
their spokes if we take the same
shrinkage factor the spokes are made
very big for instance dress take this
linkage alliances 5mm extra material so
if the spoke sizes 2 mm and extra 5 mm
diameter over that that can make a spoke
of 7 mm so the factors according to the
size for instance the ribs and similar
features should be determined and that
can be put separately to the parts which
are being made structure to the portions
of the part that is main structure for
our channels and who
fools will be too large thus simply
using largest shrinkage value is not an
acceptable solution so this is connected
ribs and similar features will always be
at least a big as desired symmetry and
channels and holes will be too large
right thus simply using the largest
single wedge is not an acceptable
solution in order to make sure that
there is enough material left on the
surface to be machine adding a skin to
the original model are also necessary
adding the skin means there should be
some material that is to be machined
that material has to be left everywhere
many studies have shown that shrinkage
variations are geometry dependent even
when using this same additive
manufacturing or furnace process
parameter settings so shrinkage alliance
is similar to that in casting and in
additive manufacturing
next is machining strategy for accuracy
improvement
now machining strategy is very important
for finishing additive manufacturing
parts and tools considering both
accuracy and machine efficiency adaptive
raster milling of the surface plus hole
drilling and sharp edge contour
machining can fulfill the needs of the
most part adaptive raster milling when
raster machining is used for milling
operations step or distance between
adjusting tool paths is very important
parameter that controls our machining
accuracy and surface quality it is known
that higher accuracy and surface quality
require a smaller step over distance and
vice versa so step over the sense
becomes an important parameter here so
this is adaptive last remaining next is
sharp edge contour machining sharp edges
are obtained the intersection curves
between features and surfaces normally
these edges define the critical
dimensions when using raster milling the
edges parallel to the milling direction
can be missed
causing large errors so these need to be
countered when step over distance is
used so this D is the step over distance
this D step over distance and W is a
slot width even when the CNC machine is
perfectly aligned the slot width error
will be at least so this is slots with
error which is to D minus Delta 1 minus
Delta 2 Delta 2 is on AAPIs then the one
is on upper side Delta 2 is in the lower
side so this is W with it's actually
obtained here Delta 1 and Delta 2
represent the offset between the actual
and desired location when Delta 1 and
Delta 2 becomes 0 this Giroux error
becomes 2d which means that the possible
maximum error for the slot using raster
milling is approximately two times the
step over distance this week we can use
here this is 2 D minus 0 minus 0 is
equal to 2 D so this is one of the
models that determines this step or
distance now third machining strategies
hole drilling circular holes are common
features in parts and tools using
milling tools to create holes in
inefficient and the circularity of the
holes is poor therefore a machining
strategy of identifying and drilling
holes is preferable most challenging
aspect is to recognize holes in the STL
file as 3d geometry is represented by a
collection of unordered triangular
planar facets and thus feature
information is lost people have used
algorithms in recognitions of the hole
did better days just based upon because
the hole and the surface have a closed
loop here so these algorithms which are
made up of sharp edges from the model
they are used to determine the holes now
the closed loops may not be necessarily
the intersection curves between the
holes on surface so a series of hole
checking rules are used to remove the
loops they do not correspond to the
drill holes so
this is also one of the important
machining strategy that needs to become
on the intersection come between the
hole and the surface is typically a
closed loop by using this information a
hole recognition algorithm begins by
identifying all closed loop made up with
the sharp edges of the model so these
are used by researchers to develop the
algorithms and to develop the STL file
only that has the hole drilling strategy
in it next is a static improvement so
many times a little bit affecting parts
are manufactured just for displaying in
the showroom or some marketing
strategies some marketing products are
to be there so their aesthetic
improvements is very important so highly
aesthetic and appealing products are to
be developed in a determined fracturing
for that post processing options
discussed in the above slides can be
used in some cases a difference in
surface structure between one region and
other may be desired
this is often in the case of jewelry so
the statics of the parts is of the
critical importance for its end
applications often the desired aesthetic
improvement is solely related to surface
finish so in this case finishing of the
selected surfaces is only required in
cases where the color of the additive
inferior part is not of sufficient
quality several methods can be used to
improve the part aesthetics some types
of parts can be effectively colored by
simply dipping the part in to die of the
appropriate color so this method is
particularly effective for the part
created from powder beds as inherent
porosity in these parts lead to
effective absorption so if painting is
required the part made neaby need to be
sealed prior to painting common
automotive paints are quite effective in
these instances in other in aesthetic
enhancement which also strengthens the
part and approves wear resistant this
chrome plating so in this figure a SLA
part that is SLA part it is produced
maybe using nylon that is chrome-plated
and after chrome plating several
materials have been coated for additive
infecting parts including nickel copper
and other coatings in some cases these
coatings are thick enough that in
addition to a setting of movements they
also helped to get a robust enough to
use as tools for injection molding or
for ABM electrodes next is preparation
for use as a pattern this is also a post
processing concern here sometimes the
parts made using reputable fracturing
are intended to be used as spectrums for
investment casting sand casting and
other casting processes and the other
replication processes may be so then the
use of additive manufacturing pattern
for metal pass creation creation using a
secondary molding or casting process is
often the least expensive way to use
additive instruction to produce a metal
part as many of the metal based a
determining processes are still
expensive to own and to operate the
accuracy and surface finish of an
additive manufacturing pattern will
directly influence the final part
accuracy and surface finish so special
care must be taken to make sure that a
pattern has desired accuracy and surface
finish in the final part also the
pattern must be scared to compensate for
any shrinkage that take place in the
pattern replication steps because we are
talking about patterns here again
shrinkage would come into play the
certain patterns that needed to be
prepared from the rapid fractured part
number one is investment casting
patterns in the case of investment
casting the item affecting pattern will
be consumed during processing for this
instance residue left in the mold as the
pattern is melted or burned out is
undesirable this is the example of
investment custom patterns rings for
investment casting made using
this specific printer now these are
drinks which are developed for
investment casting so these are the
petrol those I use is a patterns made
into the final rings it's the final
product and this is the pattern this is
additive manufacturing in the rings are
made a little networking or opinion
fracturing next is sand casting patterns
both binder printing and border bed
fusion processes can be used to directly
create sand mold codes and cavities by
using thermosetting binder to bind sand
in that desired shape one benefit of
these direct approaches is that the
complex geometry course can be made that
would be very difficult to fabricate
using any other process in order to
prepare additive and searching sand
casting patterns for casting loose
powder is removed and the pattern is
heated to complete cross linking of the
thermoset binder and to remove moisture
and gaseous byproducts this is one of
these sand casting patterns that is for
a cylinder head of v6 24-volt car engine
during loose powder removal and and the
right is the pattern prepared for the
casting alongside a finished casting so
this is the pattern this is the casting
that is obtained
so this is loose powder and it is sand
custom patterns which are prepared from
rapid manufacturing property enhancement
the last post-processing concern that
we'll discuss in this lecture property
enhancement nor thermal techniques
powder based and extrusion based
processes often create porous structures
in many cases that porosity can be
infiltrated by higher strength material
such as sino pilot newer property
methods and materials have also been
developed to strengthen the various
additive manufacturing parts the normal
thermal techniques one of the best-known
technique is tempering the prototyping
tempering process repertory pampering is
a collection of materials and treatment
operations used to increase a strength
ductility heat deflection and the other
properties this is rapid prototyping
tempering this is non-thermal technique
it helps to increase the strength then
ductility then heat deflection
then flammability to the distance or a
distance to flammability in other such
properties so this actually induced the
nano composite reinforcements that help
to tamper the material and these
properties are enhanced
this is non thermal technique now the
common post-processing operation for the
photopolymer materials is curing okay
after tempering we have curing here
during processing many photo
polymerization processes do not achieve
complete polymerization as a result
these parts are pulled into a post cure
apparatus that is a device that floods
the part with ultraviolet and visible
radiation in order to completely cure
the surface and subsurface regions of
the part additionally the part can
undergo a thermal cure in a low
temperature oven which can completely
cure the photopolymer and in some cases
greatly enhanced the parts mechanical
properties that is curing this is
important so there are certain thermal
techniques as well after additive
instruction processing many parts are
thermally processed to enhance their
properties in the case of beam
deposition in portable fusion techniques
for metals this thermal processing is
primarily heat treatment that is there
to form the desired microstructure and
to relieve the residual stresses so heat
treatment is an important post
processing technique that enhance the
properties properties that is it
develops the better micro structures
which are specifically to the
application that we need to apply then
it also helps to relieve the residual
stresses so this heat treatment is more
prominent in the case of metals like we
know in general casting and machining
processes where we machine or take off
the material
the material has some stresses develop
in it so we do certain heat treatments
like annealing normalizing sterilizing
so those kinds of heat treatment can
also be done here so in the instances
when traditional recipes for heat
treatment developed for specific metal
law being employed are commonly used so
traditional recipes as I said the common
heat treatment processes are used so in
some cases however special heat
treatment methods are also developed to
retain fine grain microstructure within
the rapidly affected part while still
providing stress relief and depth ility
enhancement before the advent of beam
deposition in powdered but fusion
techniques capable of directly
processing the metals and ceramics many
techniques who are developed for
creating metal and ceramic green parts
using additive manufacturing these were
then furnace and post processed so heat
treatment is one of the processes now
next is furnaces post-processing to
achieve dense and usable metal and
ceramic parts in order to prepare a
green part for a surface processing
several preparatory steps are typically
done there are certain steps involved in
this furnace post-processing we won't
move into that direction but yes furgus
was processing and heat treatment are
the major thermal techniques which are
there to enhance the properties of the
additive manufacturing repeat
manufactured parts so with this we have
discussed a major post processing
concerns in repeat manufactured parts
which are support material removal then
machining that is surface structure
improvement then we have or the property
enhancement certain people even say that
methodological or inspection and testing
is also the post processing the testing
of the material quality testing
inspection all those things then to
recapitulate we see what are the various
defects in rapid main fractured parts
how do we remove support material then
surface texture improvement concern
then accuracy improvement concerns where
we saw machining and other strategies
then aesthetic improvement where we saw
surface texture improvement then
preparation of the part to be used as a
pattern this we discussed then we saw
the property enhancement using the non
thermal techniques and thermal
techniques so with this this lecture is
over we'll meet again and discuss
further on rapid manufacturing thank you
[Music]
[Music]
[Music]