MeasurementofGearElements CompositeMethodofGearInspection To access the translated content: 1. The translated content of this course is available in regional languages. For details please visit https://nptel.ac.in/translation The video course content can be accessed in the form of regional language text transcripts, books which can be accessed under downloads of each course, subtitles in the video and Video Text Track below the video. Your feedback is highly appreciated. Kindly fill this form https://forms.gle/XFZhSnHsCLML2LXA6 2. Regional language subtitles available for this course To watch the subtitles in regional languages: 1. Click on the lecture under Course Details. 2. Play the video. 3. Now click on the Settings icon and a list of features will display 4. From that select the option Subtitles/CC. 5. Now select the Language from the available languages to read the subtitle in the regional language.
[Music]
[Music]
continuing with the measurements of tool
thickness so when we try to take a gear
so the thickness the teeth right so this
is the thickness we have to measure so
this is the here is a pitch circle
diameter and here this is what we have
to measure so measurement of the tooth
span micrometer so there is a tooth span
micrometer which is available so we will
use that and try to figure out what is
the tooth thickness the to thickness is
measured by measuring the chordal
distance over here number of teeth
chordal distance over here number of
teeth by using a tooth span micrometer
also called as flank micrometer so here
we try to measure the chordal distance
over your number of teeth it is not a
single teeth we are trying to take it's
like almost averaging so but what we do
is suppose we do one two three four
teeth next time what we do is we do two
three four five teeth so it then it is
three four five something like this so
you keep increasing and going so that
you try to get to measure three or four
whatever it is you keep measuring that
so so that is what we said Corder
distance over here number of teeth by
using a tooth span micrometer which is
otherwise called as flying micrometer
the measurement is based on the base
tangent method so base tangent method
one so here what we do is we try to take
okay this this is the center line so we
we try to take a tangent a chordal which
is a B and C next one is going to be a1
b1 and c1 next is going to be a2 a2 this
is
be too and then cord right so then it
will be C 2 so how do we use the
measurement with the tooth span
micrometer we try to take a and C we
wanted to measure so that is equal to so
AC right pitch circle diameter AC is
equal to what if you go back to that
figure it is back a 1 C 2 a 2 C 1 a
naught C naught so all these things are
nothing but the AC what we are trying to
measure so for T number of teeth called
the tooth span then AC is equal to t
minus half the pitch T is the number of
teeth half the pitch then the angle
subtended by AC angle subtended by AC
right is nothing but half minus T into
two pie by en radians so the involute
function of pressure angle Phi or del is
nothing but tan F by minus F where F is
the pressure angle this will be in given
so naught F will be an angle to angle PI
F is given so involute function of the
pressure angle del is equal to and F
minus F so f is a pressure angle
therefore the arc BD is nothing but t
minus half into 2 pi radians plus the
pressure angle which is subtended so BD
is nothing but the angle by the arc BD
into RB where RB is the radius of the
base circle okay but this what we try to
do is we try to find out what is BD AC
we found out then we for our finding out
BD further continuing with the same BD
is equal to the angle subtended by the
arc BD into RB with our B is the base
angle so thus BD can be figured out as s
so this s you can replace it
where s equal to you can replace it by t
so t minus half 2 pi by n plus 2 tan Phi
minus Phi where Phi is the pressure
angle okay RP by cos Phi where r RB is
the radius of the base circle which is
nothing but R P into cos Phi ok so when
you try to put it back into the equation
you have module n by 2 then all the
other units you know therefore the arc
length BD the arc length BD is nothing
but e n into M cos Phi pi s minus n by
PI minus 2 pi and this is the final
equation to find out the arc of BD ok
this is the del which we were discussing
about del is the involute function of
the pressure angle where Phi is the
pressure angle okay so this among the
correction karahi so del del is the
involute function of a pressure angle
that can be figured out as tan Phi minus
Phi so this is nothing but it can be
written as del equal to tan Phi minus
Phi right where Phi is a sin angle right
let's try to take a a problem and try to
solve this a tooth span micrometer is
being used to measure the span across
three teeths we are given T 3 T 3 trials
are conducted and the average value of
the span is thirty one point one two
zero millimeter the following data is
available for the gear being inspected
the number of teeths
is 32 addendum circle diameter is 136
pressure angle is given as 20 the span
of measurement is three and then
determine the percentage error of
measurement so theoretical
span with four three teeths is equal to
n M cos Phi by PI s n minus s by 2 n
plus tan Phi minus Phi okay now let us
write down n equal to number of teeth
small M is nothing but the module okay s
is this span and Phi is the pressure
angle right so M you could how do I find
out M M is nothing but addendum circle
diameter divided by e Z plus 2 right so
this is nothing but identify ammeter is
one 36 divided by Y Z is is that this
number of T 32 plus 2 so this is nothing
but module is 4 okay therefore the this
panel w3 t is nothing but 32 into 4 okay
so here this is ed this is Ed and yen
are same
in number of teeth is that is also
number of teeth okay
so 32 4 into pressure angle cost 20
degrees PI 3 s divided by 32 minus PI 2
into 32 and then it is plus tan 20 minus
PI by 9 okay this is nothing but 31
point 3 1 4 millimeter so the error is
going to be 31 point 3 1 4 minus
thirty-one point one two zero which is
zero point one nine four millimeter so
now the percentage error is going to be
zero point one nine four divided by 31
point three one four which is equal to
zero point zero zero six percentage so
this will be the percentage error which
is to be solved this problem so theaters
so this is done by tooth span micrometer
which is used to measure the the error
ok tooth span micrometer if you look at
it the composite method of gear
inspection is done by Parkinson's gear
tester this is how is a gear testing
done you have a lens to view and then
you have a you have dial gauges to
measure the deviations right and then
two gears you have so you can mesh it
and see so the gear being inspected will
be made to mesh master gear this is the
gear to be inspected these two gears
will mesh with a standard gear and the
dial indicator is used to capture the
radial error okay that this is used to
capture the radial error the two gears
are mounted on mandrel this is a
Mandarin which facilitates accurate
mounting of the gear in the machine so
that the dial indicator will primarily
measure the irregularities in the gear
under inspection the dial indicator of
high resolution is used to measure the
composite error which reflects the error
due to run out tooth to tooth spacing
and profile variation that is why it is
called as composite method of gear
inspection we will measure run out run
out we saw these are the errors then
tooth to tooth variation tooth to tooth
spacing and profile variation so this
can be easily monitored through this
composite gear inspection device so this
is otherwise called as Parkinson's gear
tester so to recap what all we have seen
in this particular chapter we first saw
a gear various types of gear then gear
terminologies what are the different
types of spur gear errors where we saw a
run-out okay so the spur gear why spur
gear because it's a most simplest gear
and if we understand here for the other
gears it will be a small variation for
example helix the teeth will be at an
angle then various methods of measuring
gear elements we saw gear profile can be
measured so gear pressure we can also
use for measuring the profile we can use
a profile project up profile projector
can also be used which is one of the
comparator technique the gear will be
kept on top of a glass plate and then
the light from the bottom of the light
will be projected then you will have
lenses so with these lenses you can
project it on top of a screen and in
that screen it will be magnified
according to our requirement then you
have a master you can place it on top of
the shadow whatever comes and try to see
the variation so here you can try to
measure the thickness you can try to
measure the involute profile many things
so that is one of the comparative
technique which is used to measure the
profile then measuring of to thickness
then composite gear inspection then we
also saw about the Parkinsons gear
tester now a composite is where two or
three errors are measured together and
then we
do it okay tasks for students so here
what we do is let us try to take a
mechanical setup where there is gear you
are meshing now what I want you is I
want you to replace this gear machine
please replace the gear machine by any
means and try to see the performance of
the mechanical setup next is so we have
seen I would like you to see the rear
wheel axle of of automobile that means
to stay a truck or a truck and
understand why the two gear axis axis do
not meet or what is the function of non
meeting so this you can browse through
and get to see or if you can physically
see that is also increased third thing
is this the herringbone you have gears
like this herringbone so can you find
out some application some application
means minimum five of its usage
in real time and the last one is in the
printers they use gears these gears do
not have major rear in spite of
continuous working how is this happening
okay so these are the five things which
are four things which are attached to
gear so please look into those gears and
then it will also be a good idea if you
can write down write down types and
number of gears used in a printer with
this you can try to have a feel what is
gear what is the importance of gear how
complex is the gear profile where are
its application okay thank you very much
[Music]
[Music]