noc18-me58 Lec 71-Theories of Stress Transfer (Part-II)

IIT Kanpur July 201
20 followers
Dec 3, 2023
Hello, welcome to advanced composites, today is the 5th lecture of the ongoing week and
what we will do is we will continue our discussion on short fibre composites and understand how
stress transfer takes place in short fibre composite.
So what we had shown earlier is based on principles of simple mechanics, the value of stress sigma
fx max is equal to tau y times L over R and what does this mean?
It means that if there is a fibre of length L on that fibre, so this is the value of stress
in the length direction sigma f, it will increase linearly and it will peak at the middle position
of the fibre.
But this relation I had mentioned and I had not given any explanation for that is that
this is only for very short fibres and I had not explained what does very short mean, so
only for very short fibres.
So now we will try to understand what does short fibre mean.
Now if you remember that when we were discussing our continuous fibre composites, we had said
that we had calculated the stress in the fibre.
So what was the stress in the fibre?
We had calculated that for continuous fibre composites, for continuous fibre composites
we had calculated that sigma f continuous, stress in the fibre was what?
It was nothing but stress in the composite times Young's modulus of fibre divided by
Young's modulus of composite.
This is something we had explained and this is a very well tested relation, so it is actually
it works very well.
So in continuous fibre composites, this is the stress.
Now as I keep on making fibre, my fibre longer and longer, this sigma fx max, so this is
sigma f, this is sigma f max.
So as I keep on making fibre longer, slowly the behaviour of this short fibre will approach
that of the continuous fibre and at some value of the length of the fibre, this value
of sigma f max will equal sigma f continuous, above that it will not increase any further.
So the maximum value of sigma f in a fibre cannot exceed, it cannot exceed sigma f continuous.
So the length associated with this peak stress is called load transfer length.
Because we would like that our composites become as efficient as possible, so we have
to ensure that the stress in the fibre is as much as possible because fibres can take
a lot of load.
So if the load transfer length is sufficient, then the stress in the fibre will be same
as that in the continuous fibre.
So this load transfer length we call is LL.
So when L is equal to LL, sigma f max, so sigma f max equals sigma f continuous.
So I pull in the equations from both sides.
So therefore, tau y LL over R equals sigma c EF over EC or LL equals R over tau y times
sigma c EF over EC or instead of R, I can put D and I put a denominator here.
So this is the load transfer length.
So if the length of the fibre is less than load transfer length, then the stress in the
fibre will be like this.
If the load transfer length is longer, if the load transfer length is, if the length
of the fibre is more than LL, then the stress in the fibre will peak at this value which
is sigma f continuous and then it will remain constant.
So what we will do is, we will make some graphs.
So this is L is less than LL and it will peak here.
This is L equals LL.
So the slope of the line will be the same.
So this is the stress.
So on the x-axis represents the z dimension and the y-axis represents the stress value.
So y-axis, it represents sigma f, stress in the fibre and what is this value?
So this stress value is sigma f continuous.
So when load transfer length, the length of the fibre is equal to load transfer length,
then the stress in the fibre is same as it would have been in the continuous fibre, the
maximum stress.
And what happens when the length of the fibre is more than the load transfer length?
So that is my, so in this case, this is how the stress is going to be.
So this is the case when L is more than LL.
So this is the importance of load transfer length.
Now the load transfer length we see, it depends on d tau y and also this term which is there
in the circle.
So it depends on sigma c EF over EC.
Now what is sigma c EF over EC?
What is the maximum value?
So if this sigma c EF over EC, this will also change.
It can change.
So EF is constant.
EF is a material property.
EC is constant, but sigma c I can keep on increasing and I can keep on increasing sigma
c till the fibre will break.
So this term, the maximum value of sigma c EF over EC is equal to sigma fu, which is
the ultimate tensile strength of the fibre, when this happens when volume fraction is
more than V critical.
If you go back and check, if volume fraction is more than the critical volume fraction,
then the maximum stress in the fibre will be same as the breaking strength of the fibre.
So this is the situation we want to have in short fibre composite that it can take maximum
possible amount of stress in the fibre.
So there is something called a critical fibre length and that is LC and LC is associated
when maximum stress in fibre can be sigma fu.
So how do I calculate LC?
Essentially I look at this equation and whatever is there in this green circle, I replace it
by sigma fu and then I can calculate LC.
So using that approach LC equals, so LC over D equals sigma fu over 2 tau y.
Now this is a system property.
It does not depend on the load which you are applying because sigma fu is the material
property of the fibre, tau y is the material property of the matrix, D is the diameter
of the fibre.
So if my fibres are longer than this critical fibre length, then when they fail, they will
fail at the fibre breaking stress.
Otherwise they will get stressed but when they fail, the failure will not be of this
type.
So my material will get utilized to the maximum possible extent if the length of the fibre
exceeds LC.
So if I am designing a short fibre composite, I have to make sure that the length of the
fibre should exceed LC.
Then I will be optimally or utilizing my composite material in a very efficient way.
No, Ef upon Ec times sigma c will be sigma fu.
So sigma c is the stress on the composite.
Stress in the fibre is sigma c times Ef over Ec and that when it becomes sigma fu, then
I get this load, I mean the critical length.
So this is an extremely important parameter and it is a property of the material system.
What I mean is that it is a property of the material and it depends on Ef, it depends
on Ec, it depends on Em, it depends on volume fraction, it depends on tau y.
So it does not depend on the load.
So this parameter LC should be used to decide L. L should always be more than LC.
This is an important point to make.
Now all this discussion has happened in the context that the matrix material is rigidly
plastic.
But in reality, as I said, the material behavior is something like this as shown here.
So if the material is like this, which is most of the cases, what do we do?
If we really want a good solution, we really want a good solution, a more accurate solution
in terms of estimating LC and things like that.
What we have to do is we have to put this kind of a material property in a model.
We construct a finite element model.
In that model, we put this kind of a material property and do the stress analysis.
So we put one fibre and matrix and we see how stress in the fibre is changing and we
keep on changing its length.
And based on FE analysis, we can calculate a better estimate on LC.
But if we do not have access to very sophisticated computer tools, then this gives us a reasonably
okay answer for starters.
So this is something important to understand.
So this is the discussion which I wanted to have.
The other thing I would like to say is that there is something also known as average fibre
stress.
So what is the average fibre stress?
Basically I am trying to calculate what is the average stress in the fibre over its length.
So this is sigma F bar and how do I calculate it?
I integrate sigma F times dz from 0 to L which is the length of the thing and I divide it
by L. This is how I calculate average of anything.
Now this has two possible values, one is tau y times L over D and this is when L is less
than load transfer length okay.
And if L is more than load transfer length, then it is equal to sigma F max into 1 minus
LL divided by 2L.
This is when L is more than load transfer length.
How did I get these relations?
Essentially if you do this integration for both the situations, you will get these equations
and the integration process is very straightforward.
So I am not going to discuss this in more detail okay.
So based on this, we will just very quickly look at a table.
So the first column is the ratio of L over LL and the second column is normalized average
stress.
So how do I normalize that?
I just sigma F bar divided by sigma F max, I take the ratio okay.
So I have different values 1, 2, 5, 10, 50, 100.
So if the load transfer length is same as length of the fiber, then this ratio is about
0.5.
In this case, it is 0.75.
In the third case, it is 0.9.
If the length is 10 times the load transfer length, then it is about 0.95.
If it is 50 times, then it is about 99% of the maximum possible stress in the fiber and
if it is 100, so this is 100, then it is 0.995 okay.
So what we would like to have is that the average stress also in the system should be
fairly close to the maximum possible stress.
So we would like the fibers, so one parameter is L critical and the other parameter is this
average fiber stress.
We would like it to be as close as to the maximum stress in the fiber.
So we would like that the length of the fiber should be several times more than the load
transfer length and the maximum possible value of load transfer length is critical length.
So if this L over LC is fairly large, then even though composites are short fiber composite,
they will behave as continuous fiber composites.
So we will not lose any functionality of that.
So that is the closure of the discussion for today.
Tomorrow, we will continue this discussion further and bring this topic also to a close.
So till then, have a good time, bye.
