noc20-ae13-lec10_Lecture-10: Review of Compressible Flows (contd.)

IIT Kanpur July 201
20 followers
Dec 2, 2023
Lecture-10: Review of Compressible Flows (contd.)
So let us conclude or rather continue the discussion on compressible flows. So from
the beginning, we have discussed one-dimensional compressible flow, then normal shock and then
we finished in the previous session the oblique shock. Now there are few more topics which I would
like to touch upon like the Rayleigh flow and all these things and that pretty much is going to talk
about I mean all the fundamental stuff, which we need in further cycle analysis all these.
So this just to move ahead, we will start with the Rayleigh flow equation. So this is one of
the topic that I would like to discuss Rayleigh flow equation. So this is also a steady 1D flow
with heat transfer, so this is important. So thus quite appropriate this kind of flow or appropriate
to treat the flow in combustion chamber as a Rayleigh flow case, because where the heat
transfer takes place. Now let us put them sort of in schematic to see how we can analyze this.
Let us say, this is a one dimensional flow and we have taken control volume between these two, which
is station 1 and station 2. This is upstream. So all your P1 rho 1 u1, h1 and downstream you have
P2 rho 2 u2 h2 and you can have Q12. So this is a constant area duct. So that is another thing
that also there is no work exchange while the heat is added, which is Q12. So that
means heat goes inside; that is the direction. So we write down the governing equations.
First thing that we will write down the continuity equation. So again this is a constant area duct
one-dimensional flow. So mass flow rate would be rho 1 is A or in other way m dot by A is rho
1. So we can write m dot is rho 1 u1 = rho 2 u2 right. Now momentum equation where we write
P1 + rho 1 u1 square is P2 + rho 2 u2 square. So these are already we have derived the equations
for steady one-dimensional flow at the starting of the discussion on compressible flow equations.
Now they look pretty similar. The energy equation would be slightly different that we can see h 0 2
is h2+, so we can write u2 square by 2 = h1 + Q12 which is h1 + square + Q12. So this is the
portion of the added heat, which shows up here and the last equation of state that we get is P1 by
rho 1 T1 is P2 by rho 2 T2. Now for a perfect gas, we derived the momentum equation like P1
1 + rho 1 u1 square by P1 = P2 into 1 + rho 2 u2 square by P2. So which will give us P2 by
P1 = 1 + gamma M1 square 1 + gamma M2 square. So that is a relationship that we get now.
Thus, we can get similarly for temperature relations, which are 1 + gamma M1 square
by 1 + gamma M2 square, which is M2 square by M1 square. Now the relationship between
static and stagnation temperature that still holds good. So this is the relationship,
which if we use this relationship back in this equation, what we can write that T0 2 by T0 1 is
1 + gamma M1 square by 1 + gamma M2 square. So this is whole square into M2 square by M2
by M1 square into 1 + gamma - 1 by 2 M2 square by so this there is a square so 1 + gamma - 1
by M1 square. So that is a sort of a little bit messy relationship, but that follows the standard
equations that one can use and derive those things. So now the similar way one can get the
total pressure and the static density ratio. Let us say similarly the total pressure and
static density ratio that can be expressed. So the P0 2 by P0 1, this would be 1 + gamma
M1 square by 1 + gamma M2 square, which is 1 + gamma - 1 by 2 M2 square gamma - 1 by
2 M1 square gamma by gamma 1. So that is what you get for the stagnation pressure ratio and
static density like rho 2 by rho 1; they would be written as M1 by M2 square into 1 + gamma
M2 square by 1 + gamma M1 square. So you get the static density ratio 2. Now once you look
at this, here is the Mach number 1. This side it would be mass number 2,
so the downstream Mach number which is Mach 2. So the downstream Mach number that M2 one can
calculate like M2 square, which would be gamma - 1 M1 square + 2 2 gamma M1 square - gamma 1.
Now all these relationship, this can be also kind of, for the critical condition it can be
reduced to all that thing. So now at critical conditions, what we can write that P by P star
that would be gamma + 1 by 1 + gamma M square. Then we have T by T star which would be M square
gamma + 1 whole square 1 + gamma M square whole square. So we are assuming M1 is that thing,
then similarly T0 by T0 star this should be 21 + gamma M square by 1 + gamma M square,
which is whole square into 1 + gamma - 1 by 2M square and similarly P0 by P0 star,
this can be written 1 + gamma by 1 + gamma M square into 1 + gamma - 1 by 2M square by
gamma + 1 by 2 which is gamma by gamma 1. Finally, the rho by rho star that is 1 + gamma
M square by 1 + gamma which is M square. So these are the condition that you can obtain
for Rayleigh equations and just I would like to touch upon this thing. The reason is that when
we will be dealing with the compressor, then the sorry combustor, the flow field inside the
combustor could be treated like that, where there will be flow with some sort of an heat addition.
So now some last week comments on some of the other factors, which would be important. One
is the we just talked about a little bit of standard atmosphere. So when we talk about
the standard atmosphere, now we know when the flow for a fluid in rest without any shearing
stresses any elementary fluid element will be subjected to 2 types of forces. One is surface
forces which is due to pressure and that is number 1 and number 2 body forces which is essentially
equal to the weight of the fluid element. So that means when we do the force balance,
so the force balance can give us this following relation that delta P is gamma K bar, where gamma
is written as the specific weight of fluid. So this is not the gamma of air and K bar is the
unit vector in positive vertical direction, which means this is opposite to the gravitational force
and what we can then write gamma is rho g. So thus what we will have del p by del x would be 0,
del p by del y would be 0 and del p by del z would be gamma, which is rho g.
So these first 2 derivatives here, they show that the pressure does not depend on x or y.
So as we move from one point to another in a horizontal plane in a xy plane like this,
let us say xy plane like this, then the pressure does not change, p only depends
on z and so this particular equation we can write in an ordinary differential equation
like dp by dz is gamma is - rho g. So this is a fundamental equation when the fluid
is at rest and can be used to determine the pressure change with elevation or height.
And this particular equation, this indicates that the pressure gradient is in vertical
direction. So and that is negative. So that is a very important information that this is when
you go in the vertical directions that is when you feel the pressure gradient and that is also
negative, so which means the pressure actually decreases as we move upward. That means, from the
sea level as you go up the pressure actually decreases in a fluid, which is at rest.
Now for the atmosphere where the variation in heights are large or something on the order of
thousands of feet or kilometer, so we need to pay some attention here that how this variation
actually occur. Now in doing that, we can consider the air to be perfect gas. This can be considered
ideal perfect gas rather. So ideal perfect gas and also the equation of state p = rho
RT can be used and what we can write this dp by dz = gp by RT; this is using p = rho RT.
So if we separate the variables and integrate, so this would look like from p1 to p2 which is
going to be ln p2 by p1 - g by R z1 to z2 dz by T. So here this g and R are assumed to be
constant over a range of elevation. Otherwise they cannot be taken out of the integration and
do this integration. So this actually provides the variation of pressure in Earth's atmosphere.
Now ideally one would like to have a measurement of pressure versus altitudes over specific range
of altitude. So measurements for a specific range of altitude; however, this kind of information
is usually not available. So thus a standard atmosphere has been determined and that can be
used for the design of aircraft. Now this was this concept of standard atmosphere. This was
developed in 1920s and since then there are many US and international committees and organizations
have pursued and developed a standard. But the currently accepted atmospheric
standard is the current one, is based on report published in 1962 and then updated in 1976,
so which is so-called US standard atmosphere. So that is a sort of idealized representation of the
middle latitude with year round mean condition of earth atmosphere. In that particular chart,
what one can see? This is let us say -100, 80, 60, 40, 0, 20. This is 0, 10, 20, 30, 40, 50.
This is altitude that is Z in kilometer. This is temperature in degree C. So up to
certain range of this and this, so this is known as this is zone 1 and
let us say this is zone 2. So zone 1 is troposphere and zone 2 is stratosphere. So
somewhere the curve looks like these, then it goes like that and like this. So this is at P = 101.3
kPa which is absolute at 15 degree C. This is at 11 kilometer is roughly 22.6 kPa; this is
something at 20.1 kilometer 5 kPa. This is 32.2 km, P is 0.9 kPa, 47.3 kilometer P is 0.1 kPa.
That is the kind of variation with the altitude one can find. So there are troposphere and
stratosphere. So what one can use the temperature variation like T is Ta minus beta Z. So Ta is a
temperature at sea level or let us say Z=0 and beta is the sort of lapse rate or rate of change
of temperature with height, then you can find out. Now these particular equations if we use
along with the previous equation, so what we get? That pressure is Pa1 - B cos Z by Ta to the power
g by beta R. So again Pa is the absolute pressure at Z0 and then one can find out.
Now for the atmospheric layer between 11 to 21 one kilometer, so temperature has constant
value. This is isothermal conditions and then again the pressure elevation relationship which
we can write just P0 exponential -g Z by Z 0 by RT0 So that is what one can use.
So P0, T0, Z0 are the pressure, temperature and altitude of lower edge of the atmosphere
and then and the higher edge one can find out, so you can form a table like that. So this is
how one can see the essential parameters like this and this is where let us say, this is 0,
20 degree, 40 degree. This is temperature this is 20, - 40 and altitude in some kilometers in this
side. So typically this is where your helicopter works. This is some low transport aircraft.
This is somewhere above; this is around somewhere 11 kilometer or something. This is where the
civilian aircraft and then top of that fighter. So this is the typical picture and if you see
the with the Mach number and the altitude, so that is what the another envelope you will get. This is
Mach number, which would be close to let us say 0, where there is a curve, then 1, then 2 and this is
15, 32, 50, these are in altitude kilometer. So low range here again your helicopter,
piston engine, turbo propeller, then you get turbofan, then military fighter, ramjet,
then commercial jet works between 65 to 80, then you have other fighter jet, so this is another
envelope which you will get. So one can see that this atmospheric variation with temperature and
pressure, which are also important for aircraft design. This is also just to give you an idea,
because this would be sort of required when we will do the analysis for the cycle analysis or
the performance analysis. So pretty much completes some of the fundamental discussion on compressible
flows and fluid mechanics. So we will continue with the performance in the next session.
