Lecture: 44

IIT Kanpur July 201
20 followers
3 Video Views·Dec 1, 2023
So, in today's session we will discuss about the magnetically coupled circuit. So, let
us start our discussion about the topic. So, basically the circuits which we have discussed
till now were conductively coupled. That means, that because of one loop the neighborhood
loop was getting affected through current conduction. That means, that both of the loops
were joined together and current was flowing from one loop to other.
Now in this case we will see when the two loops which may be or may not be connected
electrically, but they are coupled together through the magnetic field generated by one
of them. So, in those cases when we see those kind of circuit combinations we call them
as magnetically coupled circuit. So, the most common example for this is the
transformer where the electrical device is designed on the basis of the concept of magnetic
coupling. Now it uses magnetically coupled coils to transfer the energy from one circuit
to the other. Transformers are the key circuit elements of power system network. Why? Because
whenever we have to change the voltage level that means, either you are stepping up or
stepping down in the power system network, you need transformers for those cases.
So, now let us see first what is the mutual inductance. Now when two conductors or you
can say when two coils are in a close proximity to each other, the magnetic flux caused by
the current in one coil links with the other coil and thereby it induces the voltage in
the second coil and this particular phenomena is known as mutual inductance. Now let us
first consider single conductor ah single inductor where the coil has n number of turns.
Now when the current flows let us say the current I is flowing through the coil, the
magnetic flux phi will be produced around it. So, if you see the figure the current
I is flowing in the inductor and flux phi is generated. So, because of that flux generated
you will have the voltage V induced. Now how the voltage will be induced because if you
remember the Faraday's law, it says that the voltage induced in the coil is proportional
to the number of turns and the rate of change of magnetic flux. So, how we can write the
induced voltage V is nothing, but n d phi by dt. Now the flux is produced by current
I. So, therefore, we can also say that any change in phi is caused by the change in current.
So, this particular equation we can rearrange and write like this that V equal to n d phi
by d i multiplied by d i by dt. Now this component is nothing, but the inductance L. So, we can
write V is nothing, but L d i by dt. So, this particular equation now ah tells the voltage
current relationship for the inductor. Now this inductance is commonly called a self
inductance because it relates the voltage induced in a coil by time varying current
in the same coil. Now let us consider two coils and we assume
that they have the self inductances L 1 and L 2 and both coils are placed at in a close
proximity with each other. Now if coil 1 has n 1 turns and coil 2 has n 2 turns for this
particular case for the sake of simplicity let us assume that the second inductor carries
no current. So, now the magnetic flux phi 1 which is which will be coming from the
coil 1 will have two components one component that links only the coil 1. So, if you see
the magnetic flux generated in this particular coil has phi 1 1 which is ah linked to only
coil 1 and another component phi 1 2 which links the second coil also. So, what you can
say you can say the total flux phi 1 is nothing, but a combination of phi 1 1 plus phi 1 2.
Now as we know that the two coils are physically separated means they are not electrically
connected. So, we can say that they are simply magnetically coupled. Now since flux phi 1
links coil 1 because the if you see the figure flux phi 1 that is ah phi 1 1 plus phi 1 2
is completely linking this particular coil 1. So, what we can write the voltage induced
in coil 1 is nothing, but v 1 is equal to n 1 d phi 1 by d t or you can write n 1 d
phi 1 by d i 1 into d i 1 by d t. Now this will be your inductance l 1. So, you can write
v 1 is nothing, but l 1 d i 1 by d t. So, what is i 1 i 1 is the current in the coil
1 and l 1 is the self inductance of coil 1. Now the second part basically the phi 1 2
part of the total flux phi 1 only links the coil 2. So, the voltage induced in coil 2
because of the flux ah portion of the flux ah caused by current i 1 that is phi 1 2 what
would be the value of induced voltage in the coil. So, in that case what we can write
v 2 is nothing, but n 2 d phi 1 2 by d t or you can write n 2 d phi 1 2 by d i 1 into
d i 1 by d t. So, this particular section of the expression
we represented as m 2 1 and then this particular equation will be v 2 is equal to m 2 1 d i
1 by d t. What is m 2 1? m 2 1 will be the mutual inductance of coil 2 with respect to
coil 1. Now the subscript that is 2 1 written in m 2 1 it indicates that the inductance
relates to voltage induced in coil 2 due to the current flowing in coil 1.
Now let us consider the current i 2 flows through coil 2. So, if you see the figure
in the slide now i 2 is the current source connected to the coil 2 the flux phi 2 which
is generated by the current coil i 2 will again have the 2 components 1 component phi
2 2 which will link only the second coil while the phi 2 1 will link both of the coils. So,
you can say phi 2 is nothing, but phi 2 1 plus phi 2 2. Now again as was in the case
of coil 1 in this case also you will see phi 2 will link completely to the coil 2.
So, what we can write? We can write v 2 is nothing, but n 2 n 2 is number of turns in
the second coil d phi 2 by d t or if we rearrange it we it we it can be written as n 2 into
d phi 2 by d i 2 into d i 2 by d t. Now this particular portion you can write it as l
2. So, your v 2 will be now equal to l 2 d i 2 by d t. So, what is i 2? i 2 is the current
in coil 2 and l 2 is the self inductance of coil 2. Now the phi 2 1 part of the flux phi
2 will link the coil 1. So, the voltage induced in coil 1 because of the current flowing in
coil 2 can be written as v 1 is equal to n 1 d phi 2 1 by d t or you can rearrange it
like n 1 into d phi 2 1 by d i 2 into d i 2 by d t. So, this will become m 1 2. What
is m 1 2? m 1 2 is the mutual inductance of coil 1 with respect to coil 2. So, you
can write v 1 is nothing, but m 1 2 d i 2 by d t. Now this mutual inductance is the
ability of one inductor to induce voltage across a neighboring inductor. This will again
be represented it will be measured in henry's or in short you can write as capital H.
Now, although the mutual inductance m is always a positive quantity, the voltage that
is mutual voltage represented as m d i by d t may be negative or positive. So, unlike
the self induced l d i by d t because l d i by d t you can find out the polarity how
you will determine the polarity by the reference direction of the current and reference polarity
of the voltage. So, if you remember we discussed the passive
sign convention in our first week. So, you can use that discussion to find out the polarity
in case of you have self induced voltage that is l d i by d t. Now for the polarity
of mutual voltage that is m d i by d t, it is not that easy because it now involves 4
terminals. So, 2 terminals of coil 1 and 2 terminals of coil 2. So, since we have 4 terminals
we cannot use the passive sign convention directly to find out the polarity of mutual
voltage. Now, the choice of correct polarity for m
d i by d t is made by examining the orientation of the coil. That means, the way in which
both coils are physically wound and then applying the lens law along with the right hand rule
to find the correct polarity for mutual voltage. Now, since it is not easy to show the construction
detail of the coil that means, how both of the coils are physically wound what we do?
We generally use the dot convention for our circuit analysis. So, by this convention a
dot is placed in the circuit at one end of each of the 2 magnetically coupled coils
to indicate the direction of the magnetic flux if current enters that dotted terminal
of the coil. So, we show when the current enters the dotted terminal of the coil how
the mutual voltage would be oriented. Now, let us understand this particular concept
with the help of ah this figure. Here if you see the current i 1 is entering the dot. So,
the orientation if you see the coil are coil is wound like ah this if you place hand palm
in such a way that it is completely curling the side of the ah coil like if you ah place
your hand and you curl your fingers like this the coil is wound.
So, you will see when you place hand like this your thumb will be in this direction.
So, this thumb direction will show you how and in what direction your flux is rotating.
So, here the current i 1 is going inside you are getting flux phi 1 2 linking in the clockwise
direction to the coil 2. Similarly, in the coil 2 current is entering the dot and the
positive polarity of the voltage is when where the dot is connected here also the positive
is where the dot is connected. So, when you place the ah right hand in the
similar way as we did in this case your thumb will be in the downward direction. So, again
your phi 2 1 will again link the first coil in the clockwise direction. So, now, in this
particular case the dots are already placed. So, we will not bother how to place them the
dots are used along with the dot convention to determine the polarity of the mutual voltage.
So, we will see how if this is the condition how we can determine the induced mutual voltage
polarity. Now, let us understand the dot convention
first if a current enters the dotted terminal of one coil the reference polarity of the
induced mutual voltage in the second coil is positive at the dotted terminal of the
second coil. So, if current is entering here the mutual inductance will have the positive
polarity in the dotted side of the terminal. Now, if the current leaves the dotted terminal
of one coil the reference polarity of the mutual voltage in the second coil is negative
at the dotted terminal of the coil. So, suppose if the direction of current is
opposite and current is flowing from this side in that case the polarity of the voltage
that is induced mutual voltage would be like this. So, that means, that the second coil
the mutual voltage in the second coil will be negative at the dotted terminal of the
second coil. Thus the reference polarity of the mutual voltage depends upon the reference
direction of inducing current and the dots on the coupled coils. So, these two things
are important to find out the reference polarity of the mutual voltage.
Let us understand this particular phenomena with the help of couple of examples. Let us
see this particular figure where the sign of mutual voltage v 2 is determined by the
reference polarity for v 2 and the direction of i 1. So, if you see the current i 1 is
flowing inside the dot the reference polarity for v 2 will have positive at the dotted side
of the terminal on secondary side because i 1 enters the dotted terminal of coil 1 and
v 2 is positive at the dotted terminal of coil 2 the mutual voltage will be positive
m d i 1 by d t. Now, in this case now i 1 is entering the
dotted terminal of coil 1, but the v 2 is negative at the dotted terminal of coil 2
because the polarity of v 2 is opposite the dotted terminal is having the negative. So,
the mutual voltage will be minus m d i 1 by d t. Now, similarly in this case when the
current is flowing in second coil. So, the current is flowing as i 2 is flowing in the
second coil that means, that i 2 is leaving the dot. So, that means, if the it is leaving
the dot the value of mutual ah induced voltage will be negative ah at the at the downward
terminal and positive at the dotted terminal. Similarly in case of i 2 when i 2 is exiting
the dot, but the voltage polarity at the second will have minus at the dotted terminal
in that case your induced mutual voltage will be m d i 2 by d t.
Since here you are exiting the dot and the polarity of voltage at the dot is negative
it means that your mutual induced voltage would be m d i by d i 2 by d t which is positive.
Now, let us consider the circuit where the coils are electrically connected also. So,
if you see that coil l 1 is connected to l 2 physically as well as magnetically. Now,
in this case if the current is going inside the dot and in this case again the current
is ah going inside the dot the total inductance will be the adding connection that means,
l 1 plus l 2 plus 2 m will be the total inductance of this arrangement.
Similarly in the second case where current i is entering the dot and here current i is
again leaving the dot that means, that the mutual inductance will be in opposite direction
and the total inductance will you will get as l 1 plus l 2 minus of 2 m because this
is called opposing connection current is going inside the dot from one direction, but exiting
the dot from other side. So, now, we can say that we know how to determine the polarity
of the mutual voltage. Now, let us solve few of the circuits. So, that we can understand
how you can involve the mutual inductance and in our circuit analysis.
Let us see this particular figure where we have v 1 and v 2 two voltages applied across
the two coils which are placed nearby. So, these two are magnetically coupled. So, we
can use Kirchhoff voltage law to ah write the equations for both of the meshes. Let
us say that the current i 1 ah in this particular mesh is in this direction i 2 is in this direction.
So, for coil 1 what we can write v 1 is nothing, but i 1 r 1 plus l 1 d i 1 by d t because
of the coil 1 self inductance then plus m d i 2 by d t. Now, here in both of the cases
your current is going inside the dot for reference polarity is positive in both of the sides
where the dot is connected it means that the mutual inductance ah mutual voltage which
you get because of the magnetic coupling of these two coils will be positive.
So, you can write v 1 is equal to i 1 r 1 plus l 1 d i 1 by d t plus m d i 2 by d t
or in frequency domain you can write v 1 is equal to r 1 plus j omega l 1 into i 1 plus
j omega m i 2. Now, for the second coil what you can write v 2 is equal to i 2 r 2 plus
l 2 d i 2 by d t plus m d i 1 by d t because induced mutual voltage will be of positive
polarity in this case also you can write v 2 is equal to r 2 plus j omega l 2 into i
2 plus j omega m i 1. So, now, let us take another example where
we consider the circuit as shown in the figure here in the first part of the circuit we have
voltage v connected while in the second part we have load that is Z L connected. So, how
we will write the ah the loop equations for both of the legs. Now, let us apply KVL to
coil 1. So, for coil 1 it is Z 1 plus j omega l 1 into i 1 here your mutual voltage is negative.
So, you will write minus j omega m i 2 because i 1 is going inside the dot here i 2 is coming
outside the dot and if it is positive then your the mutual voltage will be negative.
So, what we will write we will write v is equal to Z 1 j omega l 1 into i 1 minus j
omega m i 2. Similarly, for second coil what we can write there is no voltage source we
will write 0 is equal to Z L plus j omega l 2 into i 2 minus j omega m i 1.
So, you can see that in both of the cases how the mutual voltage polarity is changing. Now,
let us take one example ah to calculate the value of i 1 and i 2 in the circuit. So,
in this case we have applied voltage that is 12 volt angle 0 and in the second coil we have
applied 12 ohm as a resistance we will again use the KVL. Since, in this case also i 1 is
going inside the dot i 2 is coming outside the dot your polarity for the mutual voltage would
be negative. So, we will write minus of j 3 into i 2 for this and minus j 3 into i 1 for the second
coil. So, for mesh 1 what we can write minus 12 plus minus j 4 plus j 5 into i 1 minus of j 3
into i 2 for mutual voltage. So, you get after simplification you get j i 1 minus 3 j i 2 is
equal to 12. For mesh 2 you can write minus j 3 i 1 plus 12 plus j 6 i 2 and if you simplify you
get i 1 is equal to 2 minus j 4 i 2. So, what you get you just put the value of i 1 in this first
ah mesh equation and simplify you get i 2 as 2.91 angle 14.04 and i 1 is equal to 2 minus j 4 i 2
that is 13.01 angle minus 49.39. So, using KVL again you can solve the circuits where you see
these kind of magnetically coupled coils. So, the important thing which you have to remember
is that how you will find out the polarity of mutual voltage. So, with this we can close our
today's session where we discussed about the magnetically coupled circuit. We will discuss
ah we will continue our discussion on the magnetically coupled circuits in the next
session also where we will discuss about the energy stored in the magnetically coupled circuit.
And then we will also see the ah ideal transformer and its ah various equations. Thank you.
