Broken 1885 Gilbert Clock | Restoration

Legacy Conservatory
14 followers
#antique
Watch how I try to bring this antique clock from 1885 back to life. This clock is a family heirloom passed down to me in complete disrepair. The case is broken in multiple spots, parts are missing and the clock does not work. The clock is an 1885 Gilbert "Altai" Mantel Clock made by William L. Gilbert Clock Co. in Winstead, Connecticut.
This is only the second clock I've worked on so far. It's so much fun learning how to restore clocks. I'm not a professional clockmaker by any means and I definitely have much more to learn.
Thank you for watching and going on this journey with me. I hope you liked this video! Please feel free to like, comment and subscribe. :)
Hey, thanks for joining me. What we've got here is a really old clock. It's been in
my family for as long as we can remember and we've never seen it running before
so I'm hoping I can get into it and see what's going on with it and see if I can
this is and what model and who made it and things like that. The label on the
back had a little bit of information on it and was able to figure out that it's
the fun stuff. So we got to get the the hands off and the dial off. This wasn't
too bad. It is missing a screw so that's something I'll have to address towards
the end when I start putting it back together. One thing that I noticed once I
took the dial off is there's writing on the back and it's hard to read but it
says cleaned and repaired November 11th 1891 and cleaned again in 1896. So that's
really cool they put that on the back there. Now I can get in here and get the
movement out. Another thing I noticed is there's only two screws holding the
movement in. So once I put the movement back in I'll have to secure that with
four screws. It's also missing the suspension spring so I'll have to try to
find another one of those probably on eBay. So I'm just taking the first looks
at it now and seeing if there's anything that's that's broken or anything else
that's missing. Just trying to figure out how this thing works and start
taking apart and get to cleaning. So before I completely disassemble this
whole movement I like to secure both springs with zip ties and this prevents
is only the second clock I've worked on and so I'm just figuring things out as I
go. I don't really know exactly what I'm doing so as you can see here I'm trying
to take off this top plate but there's these two gears called the stop works
and it's kind of preventing the top plate from releasing. So once I get those
popped off the top plate just comes right off. Once that's off you're just
left with just a pile of parts and gears and it's a it's a mess. It looks
really complicated. I like to look at each part and see if there's any damage
or anything that's noticeably wrong and then I can start getting things ready to
springs really makes life a lot easier once you get to this stage. The springs
aren't unwinding the zip ties are holding them in place and you can just
set them aside and clean them as best as you can. So now I'll get all the small
parts in these little baskets and I'll get it into the ultrasonic cleaner and
then I'll start cleaning these other parts with soapy water while that's
running. So it took a long time to clean everything and I'm not showing you
every detail here but I'm just showing you kind of highlights of what I had to
do. You know I sent parts through the ultrasonic cleaner. I'm using soapy water
here and then I also try to scrape and and get all the the dirt and the grime
and the caked on bits off of the parts. You can see how dirty the water is and
so that's just after five or ten minutes through the ultrasonic cleaner.
So here I'll use mineral spirits and get those last bits of grime off and one
thing I should have used is the right kind of gloves because those aren't it.
The mineral spirits ate right through those so I had to take them off. If
you're planning on trying this just try to plan ahead and get the right gloves.
Now that everything's clean I can get things back together and it's not as
simple as it appears here. One thing that helped was having some reference video
on where things go. Also it just takes a lot of patience and fiddling with all
the different parts and the gears just to get everything lined up and in their
correct position. As you can see I have to sometimes take things out to put
things in and so it can get pretty time-consuming but eventually got
everything back together. So getting this top plate back on is probably the most
time-consuming part of this process at least for me. There's a bunch of gears
each one of those have a pivot that have to go in to the correct pivot hole and
so getting everything lined up all at the same time is super tedious. It takes a
lot of patience and I definitely had to cut video out for this process because I
couldn't show it all. But eventually I got it. One thing that helped me was
starting in a corner and getting those gears correctly aligned and then
securing that corner with a nut. You don't want to tighten it down all the
way just enough to keep the plate from popping back off and then you'll just
move through the movement gear by gear and then once you get everything aligned
and the plate seated correctly you can tighten up all the nuts at the very end.
So now that I have the movement all back together I'm gonna give each spring a
few winds and I'm not gonna wind everything all the way because at this
point I'm kind of nervous about the condition of the springs. I don't know if
they're gonna break on me or anything like that so I just give it a few turns
just to get some power and then then I can start greasing the gears and oiling
only cost me about five dollars and took a few days to get here. There's a
couple problems here. The hammer isn't striking and the chime works on the left
aren't stopping and so I took the movement back out and found that the
count lever isn't stopping in each of these deep notches. So there's three
things that must happen for the clock to chime correctly. The count lever needs to
fall into a deep notch on the count wheel. The maintenance lever needs to
land in the bottom of one of the maintenance cam notches and the locking
lever needs to fall into the path of the warning pin and stop the wheel from
turning. So while I was trying to figure this all out I also noticed there's a
bent tooth on the count wheel and so I very gently straightened that up and
corrected that. But I found that the main problem was the warning pin was
missing the locking lever. So I had to take the movement back apart and adjust
the warning wheel by turning it 25% or so and putting the movement back
together. So once I fixed that then everything started working the way that
it should. So the teeth in between the deep notches chimes the number of times
for the hour. The second deep notch chimes on the 30 minute mark. Here I'm
lifting the count lever with my finger just to test some things out. But in
normal operation the center shaft cam which controls the minute and the second
hands will lift the lifting lever which then lifts the count lever out of one of
those deep notches. So now we can address this case. So it's broken in a
few spots. There's areas where the glue had broken loose causing things to
shift around. So this not only will make the clock look better but more
importantly it will make it work better. Because a case that's that's loose will
actually steal momentum away from the pendulum swing and you could have
things like beat errors or it incorrectly keeping time. You could even
have the pendulum stop swinging altogether. So it's important to get
everything shored up and tight and all back together the way it was meant to be.
Here I'm just taking a chisel and removing the old glue and this way when
I apply new glue everything fits tight back together. So when I put the case
back on the base if I don't get it exactly lined up the way it was before
these unstained areas would show through. So I decided to add a little stain and
kind of blend things in. For the most part it's all going to be covered up
here and the areas that were already sealed the stain didn't absorb into the
wood anyway. So I figured it wasn't gonna cause too much of an issue. This
part was pretty time-consuming and I'm not showing everything I did but I'm
just going through every little nook and cranny and getting all the dust and dirt
we can get the movement back in get it wound and see how things work. So if you
remember the movement was only held in by two screws and the other two screws
must have fell out at some point. But I was able to go to the hardware store and
find new brass screws to use and this will keep the the movement solid against
the case so the pendulum doesn't lose any momentum when it swings back and
in I'm just going to do another test and see how things are working. So there's a
couple things I didn't show in this video. One is how I put the clock in beat
and the second is how I adjusted the beat rate so it doesn't tick too fast or
too slow. So if you have a question on how I did those things just shoot me a
clock from 1885 brought back to life.
