Lecture 11 Module 1

IIT Kanpur July 201
20 followers
Oct 21, 2023
Welcome back, this is lecture 11. A few lectures back, we saw that in order to make a good
amplifier which can indeed amplify power, we needed a device or we needed a network
that had the following small signal characteristics, right. So, if our two port network were like
this, if the two port network model for the incremental network were like this, where
this conductance is Y11, this conductance is Y22, the transconductance in the input
side is Y12 times V2, where V2 is the voltage at the output port and the transconductance
at the output side was modeled as Y21, V1, where V1 was the, where V1 was the voltage
at the input port, right. And if we were to connect, we were to connect
an input with a finite source resistance Rs at the input port and if we were to take the
output across another resistance RL across the output port, then we saw that and wish
list for our ideal. So, wish list for an ideal amplifier would have been Y11 should be 0,
Y12 should be 0, Y22 would be 0 and Y21 should be as large as large as possible, right.
Then in our quest for finding such a device, we landed up with one such device which was
which was a MOSFET and N-MOSFET in particular which is a three terminal device, right, which
is a three terminal device. The port 1 is connected between the gate is V1, the port
1 is connected between the gate and the source and the port 2 is connected between the, between
the drain and the source and then we saw that, then we saw that if the MOSFET is in
saturation, right. So, under saturation condition that is what
is saturation condition? Saturation condition is firstly, it has to be on, right. The MOSFET
has to be on which means voltage between the gate and the source has to be greater than
some threshold voltage which is a characteristics of the MOSFET that this threshold voltage
Vth will be given to us, right. It is a characteristics of the MOSFET and under saturation condition
that is Vgs should be greater than Vth. Another, we need to satisfy another condition that
is Vds, Vd minus Vs should be greater than Vg minus Vs minus threshold voltage, right.
In other words, you see that source is common between both sides of this inequality. So,
they go off which means that we just have to ensure that the drain voltage is greater
than gate voltage minus 1 threshold voltage, right.
Essentially, if we can ensure these two conditions that is Vgs is greater than equal to the threshold
voltage and the voltage at the drain or rather this voltage difference between the gate and
the drain, the voltage difference between the gate and the drain is not less than a
threshold voltage, right. So, what is this inequality telling us? This inequality can
also be written in the form of Vg minus Vd, right. Vg if I move it to the other side Vg
minus Vd should be less than equal to threshold voltage, right.
So, in other words, what is it saying? It is saying that the gate voltage, the voltage
at the gate can be even higher than the drain voltage, but by a maximum of 1 threshold voltage,
right. So, if these two conditions are satisfied, if these two conditions are satisfied that
is Vgs is greater than a threshold voltage and drain is not lower than the gate by more
than 1 threshold voltage, right, then your saturation condition is met and under the
condition of saturation, under the condition of saturation we we get these conditions that
is y 1 1 is equal to 0, y 1 2 is equal to 0, y 2 2 which we also call as a conductance
between the drain and the source that is g ds is also equal to 0 and y 2 1 which we call
as g m is equal to mu n C ox W over L Vgs minus 1 threshold voltage.
Now, note that this g m, right, what we want y 2 1 to be? We want y 2 1 to be as high as
possible and this seems to be doable since these factors W over L and Vgs minus Vth or
in other words the overdrive is under the control of a designer, right. So, we can choose,
we can pick and choose values of W over L and Vgs minus Vth or the overdrive of the
MOSFET. Since we can pick and choose these values, we should be able to get a value of
a value of y 2 1 which is sufficiently high, right.
So, if this is possible, if this is possible, what is the next step? The next step is to
see how can we use this MOSFET, how can we use this MOSFET to suit our purposes, right.
So, in other words what we are asking is that, ok, it is well and good that it is well and
good that does this MOSFET seems to, MOSFET in saturation seems to satisfy the conditions
that is required to get amplification of power, right, but I mean ultimately you have to put
things together. We cannot just simply say here is your MOSFET, bias it in saturation
and we will get amplification of power, right. We will have to ensure that, we have to ensure
that this is indeed achieved, right. So, let us, so next step, next obvious step
is to see how can we achieve both, right. So, what is the thing, what are we after?
The next goal is to, next goal is to bias the MOSFET in saturation and apply a small
signal input or an incremental input to get amplification, ok. So, let us dive in. So,
what is the incremental model of a MOSFET? The incremental model of a MOSFET, let us
do both together. So, what is the incremental of the, incremental picture of a MOSFET? The
incremental picture of a MOSFET is this. So, this is g m times v 1. What is the v 1? v 1
was is this voltage, this is v 1, but note that this v 1 is between a gate and a source. So,
g m times v 1, we can also write it as g m times v g s, right, g m times v g s, right.
And where are the incrementally, where are the inputs and the outputs connected? Incrementally,
a source will be connected here, i dot s and the load will be connected here, right. So,
incrementally if this is, if this is achieved, what will be, if this is v naught, what will be
v naught over v i? So, v naught, v naught is nothing, but the current that is g m times v g
s, right, the current that is g m times v g s times R L, but the sign will be flipped because
of the way the voltage v naught is marked, right. I am drawing current out, I am drawing current out
of the resistance R L. So, v naught is that voltage difference across R L is minus g m times
v g s, this is the current times R L. What is v g s? What is v g s? How do I know what is v g s?
v, if I do a KVL in this loop, in the input loop. So, if I do a KVL in this input loop,
what do I get? Is there firstly, is there any current in this input loop? No, there is not,
because I have an open circuited at the input terminal, right. So, there is no current.
Since there is no current, what do I get? v g s is equal to v i. So, if that is the case,
if I, if I plug in this value in the top equation. So, v naught becomes minus g m times v i times
R L and v naught over v i that is the small signal gain becomes minus g m times R L, ok.
So, so is this, is this good or a, is this good news or a bad news? Clearly, this is good news,
because now this gain, right. So, this gain, this A v is minus g m times R L and can this be
made as high as possible? Clearly, yes, because R L is, is fixed, because R L is has been given
to us by some external specification, but this value of g m, right, this g m is a designer
control variable, right. The g m is a designer control variable, we can tweak the g m, right,
we can design the g m to suit our purposes by changing, by changing the W over L, the aspect
ratio of our device, right or by changing the over drive of the device, right or changing v g s minus
v t h or by changing the over drive of the, of the device, right. And note that this v g s minus v t
h or the over drive are, are the quiescent parameters, right. So, that is the, these are
the parameters at, these are the quiescent voltages at which our MOSFET is, has been,
has been biased, ok, ok. So, now, now the question is this is, I mean,
this still is an incremental, incremental model, right. I mean, I do not see a MOSFET here,
I see the incremental model of the MOSFET. So, we have to put a MOSFET in this case, right.
So, what if, what if, what is the next thing? So, what we will see, try to see is,
what if we replace this incremental model with its, with a MOSFET, right. So, let us do that.
So, how should we replace the incremental model with the MOSFET? Now, note that,
note that in a MOSFET, the gate is one terminal, right. So, if this I, if this is v 1,
the v 1 is the voltage between the gate and the source. This is gate, this becomes a source,
right and v 2 is the voltage between the, is voltage between the drain and the source, right.
So, let me put it here. So, v 1 becomes the voltage between the gate and the source
and v 2 is the voltage between the drain and the source, right. So, how should I
connect the MOSFET? The MOSFET is connected like this, ok, right. So, let us redraw this, ok.
Now, who decides again, who decides which is the drain and the source terminal because the MOSFET
is physically symmetric device. Clearly, the voltage, the terminal between drain and source
which is at higher potential is the drain, right because pinch off happens, I mean,
you apply the voltage, when you apply a higher voltage at the drain side, the electrons in the
channel get sucked out from the source and get dumped on the drain or drained out from the
terminal that is why it is called, it is called a drain, ok, fine.
So, now, we need to ensure that this is, what is the first thing we need to ensure? If we,
ok, let me do this experiment with you and if I say that if I directly connect these sources and
these loads here, what is going to happen, right? So, let us do this experiment. So,
let us say I connect, I connect the source Vi and the load RL like this, what is going to happen?
And for the sake of simplicity, let me just say that this common terminal, the source seems to be
a common terminal between the input and the output, right, the source seems to be a common
terminal between the input or the output and we know that every reference circuit, every circuit
that we do has one common terminal with respect to which we define all the voltages, right,
because the absolute value of voltage does not have any meaning, it is always a voltage difference
between the two nodes that we are referring to and when we say that the voltage at this node
is 2 volt or 5 volt or 3 volt, we implicitly assume that there is one reference terminal
from which we are, the difference from which is 3 volt or 5 volt or 2 volt or whatever you are
measuring and that reference terminal, that common terminal we typically call it as, as ground.
So, since in this particular configuration, note that it is not true for all configurations,
in this particular configurations, since the source is, seems to be the common terminal
between the input and the output, right, so we call this, we call this, let us call this ground,
right. So, we call this as a, why is the colour not changing, let me change the colour.
So, we call this ground, right, since, so since source is the common terminal, we will,
we call it ground. So, what I would request you to do is to, is to take a moment and tell me
what will be, what will be the V0 over Vi or what will be the, what will be the procedure
that we should follow in order to figure out what will be V0 over Vi, right.
We will see you in the next class.
