Lecture 01 : Module 01

IIT Kanpur July 201
20 followers
Oct 23, 2023
Welcome to Analog VLSI Design, this is lecture 1.
As we had seen in the introductory video, in this course we will be almost exclusively
focusing on designing an amplifier.
Now, this is a course for electrical department or electronics department.
So, when we when we talk about amplification amplifying something, we are essentially
talking about amplifying an electrical quantity, right.
So, what is the most familiar electrical quantity that we can amplify?
Obviously, we can say that let us start off with voltage, right.
So, when we are planning to design an amplifier, the question is are we planning to design
a voltage amplifier, right.
So, what do I mean by that?
So, let us assume that I have a voltage source, let us assume I have a voltage source V in.
Let us further assume that it has an internal resistance R s, right, because no voltage
source comes with zero internal resistance, it is always a real life voltage source is
always accompanied by an internal resistance, let us call it R s, where s stands for the
source and let us say there is a load resistance R l, right.
What are we interested in?
Are we interested to build a block and put it in between R s and R l, such that after
we connected this block, the voltage that will develop across R l, right, let us call
it V naught.
So, are we interested in building a block, let me just put a question mark here.
So, are we interested in building a block such that V naught is equal to A v times V
in, where A v is greater than 1, right.
So, are we interested to build this?
One might say that if we have such a block, we might as well call it a voltage amplifier,
right, can call this a voltage amplifier.
So, is the course about finding out what is the stuff inside this box, which can give
us voltage amplification?
Now, some of you might turn around and tell me that hey, what is so holy about voltage
in electrical domain, we have another quantity that we are equally interested in that is
a current, can we make a current amplifier, right?
Why are you partial about amplifying voltages, right?
So, you will also be right.
So, let us say that I have a current source, let me call it I in, the current source is
again accompanied by an internal resistance R s and I have a load resistance R l.
What should I, so is the course about building this box inside such that the current I naught
that will flow into R l, right, I naught is equal to some proportionally constant A I
times I in such that A I is greater than 1.
And if this is realizable, if we have been successful in realizing this, we can call
this a current amplifier and you will be right, right.
Because, if we are able to realize the box on the top, we can say that that box is a
voltage amplifier.
If we can realize the box in the bottom circuit, then we can say that the box acts like a current
amplifier.
However, in this course, we are neither interested in designing a voltage amplifier nor a current
amplifier.
What we are interested in is the following, we are interested in building a box such that
if I put this box in between the load and the source, if I put this box between the
load and the source, then the power delivered to the load, right.
So, the power delivered to the load P out, right, should be greater than the power that
I am extracting from the source.
In other words, if the power that is going in is P in and the power that is getting delivered
to the load R L is P out, we are interested in finding out this box such that P out is
equal to let me call some proportionally constant A p times P in, where A p is greater than
1.
So, this course is focused in designing this box where the output power is greater than
the power that is that I am extracting from the source.
The source might be voltage source, the source might be current source, it does not really
matter.
All we are interested in is to deliver an output power which is greater than the power
that we have extracted from the source.
And why is this relevant?
This is relevant because there are several applications which demands this.
For example, the most common application that you might be familiar with is that of a microphone
and a loudspeaker.
The volume that comes out of the loudspeaker is much much stronger than the decibel level
of the volume that is a decibel level of the signal that is going into the microphone
right.
So, clearly there is a power amplification that is that has happened.
It is neither a voltage amplification nor a current amplification.
Let me try to convince you with a concrete example of what I mean.
Let us take the example of a humble transformer.
I am sure you have gone through or you have encountered an ideal transformer in your basic
electrical engineering courses right.
So, for example, you have let us say I have this again this non-ideal voltage source and
I have this load resistance RL and I put this transformer in between and let me mark
this transformer turns ratio as 1 is to n right.
What is a transformer?
An ideal transformer is nothing but all we need to know for the purpose of this discussion
is an ideal transformer is the following if this is V1 and I have a turns ratio of
1 is to n, the other terminal will be the voltage across other terminal will be n times
V1 right and also we know that if I have a load resistance RL connected to the secondary
of the transformer that is on the right hand side of the transformer in this case it that
load resistance gets reduced by a factor of n squared obviously, if n is more than 1 ok.
So, these are the two things that we need to keep in mind in order to solve this problem
ok.
So, what I what are we interested in?
I am interested in figuring out what is V naught.
So, what is V naught over Vk?
We are interested in we are interested in figuring this out ok.
So, how should I go about figuring this out?
So, we know that the resistance looking in that is Rn for an ideal transformer in this
case will be RL over n square right.
So, if I remodel if I remodel this circuit right if I remodel retrog this circuit like
this.
So, this becomes P in R s and a resistance of value RL over n squared and if I mark these
voltages as V 1 this voltage becomes V 1 ok.
So, what is V 1?
V 1 is nothing, but the current that is flowing into this loop that is V in over R s plus
RL over n squared times the resistance RL over n squared ok.
So, if that is the case if this is V 1 what will be V naught?
Now, if I switch our attention to the circuit on the top I know V 1.
So, what will be V naught?
From the transformer action we know that V naught is n times V 1 which is equal to V
in times n times RL over n squared divided by R s plus RL over n squared correct.
So, if I multiply both the numerator and the denominator by n square what do I get?
I get V naught over V in is equal to n times RL by n squared R s plus RL ok.
So, if I rewrite this here so V naught over V in becomes n times n times what RL by RL
plus n squared R s ok.
So, let me redraw this circuit redraw this circuit V in plus ok.
So, if RL is much much greater than n squared time R s what happens to V 0 over V in?
In this case V 0 tends to n times V in right V 0 tends to n times V in.
So, this acts as a voltage amplifier right from the definition that we started off with
right if I take you back to the definition that we started off with in few minutes back
it seems like a simple transformer is able to satisfy this condition right ok.
Obviously one might turn around and say that hey this is limited because this is true only
for certain ranges of RL the RL has to be much greater than n squared times R s if that
is the case I will I might get voltage amplification, but nonetheless we are getting voltage amplification
correct.
However, note that we are not interested in these type of amplifiers because you cannot
get power amplification out of a transformer right.
If you are not convinced what I would like you to do is pause the video here and try
to find out what is V out over V in.
In other words what I am asking you to do is to find out what is the power delivered
find V out over V in where V out is equal to the power delivered to RL right.
So, which is effectively you can say that V naught squared average over RL and what
is V in?
V in is equal to the total voltage V 1 and the total current I 1 the multiplication of
V 1 times I 1 the average of that right.
So, you can assume V in to be equal to V p sin omega naught t right you can assume this
and try to figure out what will be p out what will be p in and what will be the ratio
of p out over p in and we will continue from there.
