WITHOUT PRODUCT REVIEWS, SPONSORS, DONATIONS AND STICKER SALES, I’d have to go back to work and not do ANY videos, because you can’t live without any income.
I'M MORRISON BLOWERS!
First of all, put the engine...
This flywheel has...
It didn't have a stator, so I found a stator.
Briggs...
Flathead and...
I'm fine.
That's the thing about...
I'm not even gonna start it up and try.
I'm on with it.
About, um...
Four years ago, the battery ran out.
I mean, uh...
It'd be a shame if it didn't work.
What, everybody?
Woo-hoo!
Hey, you guys. How you doing?
It's Henry.
I'm Morrison Blowers.
Part two of my repower project
for this Toro 1438 HXL hydrostatic lawn tractor.
Carcass that I got without an engine.
Episode one, we put a whole bunch of stuff together
from three engines to make one.
I actually did get it started and running.
I'm deaf now because it had no muffler,
so it was super loud.
But the engine runs.
Timing's good.
Gets spark.
And it runs on its own, believe it or not.
I was pretty surprised.
Problem we have is the electrical.
The Toro lawn tractors have a different wiring harness and setup
than your typical Craftsman LT1000,
Murray, or John Deere-type tractors
where the wiring harnesses are pretty much really easy.
I looked up the schematics of the 1438.
As you can see, most of the tabs on the ignition tumbler
is not your typical S, M, L, A, C, C, B, and G tabs
standing for S for solenoid, M for magneto, L for lights,
B for battery, G for ground, A, C, C for accessories, and so on.
Not to mention the tumbler on this stock one
didn't have any labeling, so you had no idea
what tab led to what.
But from the schematic, you'll see that the majority of those tabs
go to safety switches that go into a relay,
which I've never worked on.
I'm not even 100% sure how it all works.
It's very complicated.
So to not try to figure out the safety switches
by bypassing, by crawling underneath for the brake safety switch,
bypassing the PTO safety switch,
and the seat safety switch has already jumped with another cable.
But I'm just not sure about it all.
You know what I mean?
So what I'm going to do is,
I'm going to hardwire the whole thing from scratch.
So I'm going to leave the positive and negative cables
from the battery to the front.
Obviously, you need that no matter what, right?
I got a new ignition tumbler.
It's not new.
It's in my box of parts.
It's from another tractor.
But it is the same old metal kind,
which fits into the hole of the dash,
whereas the new black plastic kind,
the hole needs to be that big to get it in.
So I needed a metal one that has the small little hole
where you can stick it in and then screw it on.
You're following what I'm saying?
And this metal one that I have has the labeling to the tabs.
And this is very simple.
It only has five tabs.
S for solenoid, M for magneto, B for battery, G for ground,
and the last one, L for lights.
As you guys know, or may not know,
it only takes four wires to connect the lawn tractor battery
to a lawn tractor.
You just need a solenoid, right, to start.
You need a magneto tab to shut it off
and allow spark to go to the thing.
You need ground and you need battery.
That's it.
You only need four wires to start the engine
in basic functions of a lawn tractor.
There's nothing else.
So it's really quite simple.
Just rewiring the whole thing is going to take a while.
I'll try to use the existing wiring that's in here
and just cut the rest out,
completely bypass the relay altogether,
bypass all the wires going to safety switches,
and we're just going to have four wires
running from the ignition switch,
one to the magneto to shut it off,
one to the solenoid, which turns it on,
and then you have power, ground, and power.
That's it, four.
So I'm going to try to do that
instead of trying to fumble with the bypass
on the safety switches and the relay.
I'm just going to cut all that stuff out.
But I do want to show you
what the PTO safety switch looks like.
The battery has been charging overnight
with this old-school diehard battery charger.
This battery, I don't know if it's good or not.
I might have to desulfate it.
But anyway, here you see the safety switch
for the seat safety switch has been bypassed.
And if you come on over here,
I'm going to try to show you what this looks like.
That thing right there, you see that?
I'm going to move the PTO.
See?
When you lift the PTO lever,
it clicks off of that switch,
and then you close it that way.
Or it's closed when you lift it.
No.
When you lift it, it's...
No, that's closed.
When you lift this...
No, then that's closed.
Then it closes the circuit,
so it allows you to run.
Then when you do this,
it opens the circuit, so it shuts it off.
That's what it is.
And then the brake one on the right side here.
I mean, it's all the way on the bottom.
I can't even see.
Like that.
So this is going to take a long time.
I'm not going to bore you with it.
I'll put you on time-lapse for a little bit
just to show you how long I take doing this.
But once we get the wiring fixed up,
I should be able to stick a key in the tumbler,
turn the switch,
solenoid is engaged,
power is going from the battery to the starter,
which turns the starter bendix gear,
turns the flywheel,
creates a spark from the magneto,
takes it into the ignition coil to the spark plug,
ignites the chamber as the flywheel is turning,
and starts the engine.
As for my thoughts on why it's hard to turn, right?
Compression stroke is very hard once you get to that area.
Usually that means a bad ACR on the camshaft,
or it means your valves.
When I put this engine together,
I already did the valves,
so I'm ruling that out, kind of.
So maybe the compression release is busted on the lever,
but I did get it started once,
and that was from a battery that was just charged.
So maybe we just need a good battery
with good cranking amps for it to start the engine fine,
and maybe the compression release is not busted at all.
Because I don't know if it would work
if the compression release was busted.
You wouldn't even be able to start it,
and I did get it started.
So I'll put you on time-lapse.
Hopefully by the time I'm ending this time-lapse,
I would have hardwired the entire ignition system.
All right, I've been messing with this for about,
I don't know, an hour, hour and a half?
Not even sure.
I rewired everything.
Just took the...
You guys aren't going to understand this,
but it's just a lot of spaghetti.
I tried to make a good ground.
I was having ground issues.
I just basically took the old wires out of the module
and put it in the configuration of this new ignition tumbler.
And so I did a lot of testing with my multimeter,
and it looks like the only thing stopping me from starting this
is a weak battery.
So I was trying to start it.
It kind of cranked a little bit,
and this battery is just done skiing,
which is surprising because I thought I fixed it.
I'm trying one of my 4,000 amp power starters, jump starters.
It's got the boost on.
This ought to crank the motor.
See if it starts.
All right.
Can we crank this for the first time with a new switch?
Let's put it on choke, see if it starts.
Ready?
It's on.
All right.
Beep!
I am totally deaf now.
I can't hear a thing.
Can you believe it?
We've got it started and running.
It runs on its own.
It needs a little bit of carburetor adjustment,
but all it needs is a really strong battery.
Jump starters, they shoot out 4,000 amps into that one jolt.
But that's great news.
Our solenoid works.
My rewiring, basically hot wiring, everything,
just hard wiring it from scratch.
Like you see here, I only have four wires.
I've got a gray, which is ground.
No, gray is not ground.
Gray is the magneto.
And then the white is the solenoid.
The blue is positive, and the yellow is ground.
And then I had one that goes out of ground twice
because one is to be grounded to the solenoid and the machine,
and the other one goes to this one here,
which is the other part of the lights.
So I'm going to connect these two,
and we should have lights too, believe it or not.
So I'm going to put this tumbler back in here and clean it all up.
I just need a new battery, and this thing will run.
I have to tighten the bolts to the engine, as you saw,
I was moving around because I didn't tighten them on there too tight
because I thought for sure I'd have to remove it again.
And then I have to get a muffler.
I mean, plenty of stuff.
I've got to do plenty of stuff.
But for us to hardwire the electrical, yeah, it's a lot of work,
but it's fun.
It's not fun, but, I mean, I've done it so much
that I kind of know what I'm doing,
and it's rewarding to finally see this start up like this.
Holy cow.
We just had a tropical storm Ophelia come by this weekend,
and it's a disaster.
Holy cow.
A little pain in the balls this is going to be.
Now when it dries up, just go over it with a mower.
Man, lucky me.
I have the only acorn tree on the block.
Why, why, why me?
It's ridiculous.
So I was just screwing around the backyard, and I got this muffler, see,
and I just was curious to see if it would fit on the Toro.
So I went and put it on, and it does fit,
but it sticks out, so now you can't put the hood on.
So that's not going to work,
unless I cut it and re-weld it in an area where the hood would fit.
That's a lot of work, you know what I mean?
So I decided I was going to give my friend Brian a call,
who lives also in Huntington,
and he comes and we trade parts.
Sometimes he buys, he was the guy who bought that new LT1000 deck that I had,
and he bought some baggers, whatever.
Anyway, he's a friend of Jason's too.
We trade parts whenever he needs something, I need something,
whatever, we just trade.
Anyway, he had, I believe, the original muffler for that Toro lawn tractor.
So I went to go get it, and also I was looking all over the place
for the crankshaft double stack pulley bolt.
You know, I used to have a hundred of them, you know what I mean?
But I can't find them, it drives me crazy.
So I couldn't find it, so it means I couldn't put the double stack pulley on
so I can get the drive to work, right?
So I asked him, do you have one of these bolts?
He goes, you mean this bolt?
I said, yes, that bolt.
So I went to go pick up a bolt and the muffler for the Toro.
He didn't charge me any money for it because I'd give him some other small shit in the past.
So we just trade parts, whatever.
If it's a little bit more of an expensive item, yeah,
we'll just, you know, give each other a few bucks here and there, whatever.
Also, when he was there, he had all these trash tractors sitting around.
I says, ooh, I need the right foot pad for that hauler I got in the back.
He goes, here, take it.
So I've got some great parts.
While I was there, I was looking at his stash.
He's got this John Deere tractor he doesn't want.
He wants to give it to me.
He's got some decks, which I need for the hauler, you know what I mean?
So I might go pick up some stuff when I get to the other projects after the Toro.
But it's good to have a friend who does exactly what you do, you know what I mean?
And then between the three of us, we trade parts, you know, and vice versa.
We help each other out, so it's great.
Anyway, we'll put the new muffler on, we'll put the double stack pulley on,
and hopefully we'll be able to drive that damn thing around and see.
So look, this is what I got from Brian.
Crank shaft bolt for the double stack pulley.
Trick is to get that thread, you know what I mean?
The right foot pad for my hauler, and this muffler for the Toro.
So you see, I put this muffler on.
It fits. It fits well.
But it's just, there's too much room here.
It needs to go into that area, see?
So it sticks out too much, so you can't put the hood on.
So I'm going to go watch some football, and tomorrow I'll come out and we'll do all that.
It's been raining for like three days.
Tropical Storm Ophelia.
Tropical Storm Ophelia, so I'm going to be doing some stuff indoors today.
Before I get started on putting the muffler on and the double stack pulley bolt,
I've got something to show you.
I got this in the mail, a mini screwdriver kit.
I'm going to show you what it looks like.
Look at that.
Really cool.
From Tiswall.
Same guys that made a few other products that they sent me.
Look at that.
Whoa!
Look at those precision bits here.
Small, medium, and large phillips, some torx, some hex, and flatheads.
And also these double hole kinds.
You don't see too many of those, but it's cool that it has it.
And also super tiny for eyeglasses.
There you go. Very cool.
It comes with one of these.
It says demagnetize or magnetize.
I don't know how to use it because there's no instructions.
It just comes like this.
And also I thought that these were motorized, but it's not.
It's just a simple screwdriver set with extra long bits.
Very useful for what I do here.
From Tiswall.
The W900 series.
It is very cool and sharp.
You can put it in your glove compartment or your trunk of your car.
And if you ever need something like this, it's right there for you.
Another thing I want to show you that I got today.
Roadside emergency kit.
Just like the screwdrivers, you need them in case it's an emergency.
List of all the things that's inside.
You got some gloves here.
You got a first aid kit.
With your standard swabs, gauze, band-aids, tape, elastic tape, scissors.
Whistle for emergencies.
Black electrical tape.
Tire gauge.
A mini flashlight.
Emergency triangle.
Reflective triangle you put in the back of your car so that people can see you in the dark.
Reflective vest so that people can see you and they don't run over you.
Tow rope.
Glass breaker.
In case you're an idiot and you drive off a bridge or something into the lake and you're sinking rapidly.
And you're going to drown if you don't break the window open.
Oh, why don't you just open the door?
Well, you know that with the pressure of the water keeping the door closed, you can't open the door.
Unless you equalize the pressure.
So you break the window, swim out the window.
This is very useful to have.
Also, the bottom, you can cut your seatbelt.
Because sometimes when you're underwater, the seatbelts don't work for some reason.
You can cut your seatbelt and get out.
If you can not panic from drowning and think of all these things like waiting for the car to go all the way underneath the water.
I don't know if I would do that, you know.
I'd be panicking trying to get out.
I'm not going to wait until the whole car is underneath the water for me to break it.
And then with the panic, oh my god, I can't hold my breath.
I've got to cut the seatbelt.
But it's good to have instead of not having it, right?
Phillips screwdriver.
A pair of jumper cables.
These are very useful.
How many times do you run into people that say, hey, you got jumper cables?
You do have to put batteries and flashlights on.
Definitely two very needed items that you need in your car in case of emergencies.
A screwdriver set as well as an emergency roadside kit with a first aid kit in it.
I'll leave a link in the description for any of these two items if you guys are interested.
Now back to the video.
Okay, it's been a day.
It's still raining.
I feel like it's been raining for five days.
Today we're going to put on this muffler.
We're going to see if this fits a little bit better than what I had before.
Well, what I have right now, because this thing, the muffler, fits and works.
But it sticks out like five inches.
And because of that, the hood won't fit.
So thanks to my friend Brian who had this.
He was pretty confident that this was the one off of the Toros.
Of course, the Toros had different engines and everything.
But the way it's designed with the hood, the muffler needs to be tucked right underneath the valve cover for the hood to work.
To be able to open and close.
So we're just going to remove this one, even though it does fit.
Don't want to strip anything because once you strip it out of the head, you're screwed.
You've got to be very careful.
There we go.
Look at that.
It fits perfectly.
It even fits perfectly onto this canal that I didn't notice.
There, see?
And then this part rests right there like it was designed to.
Never noticed that before.
See?
It's designed to be resting right there in that cutout part.
Awesome.
Let's try to start her up and see how it sounds.
So I've got to get a new battery for this.
Because for the past three or four days, I've been trying to charge that battery up.
Even with the desulfator on it, it won't work.
So that battery's done-ski.
So I definitely need to go get one.
So I'm going to use one of my chargers from a review.
And now we have it on boost, too.
So it's really going to crank.
Got it on choke. Here we go.
Let's see how it sounds.
All right. Works great.
I want to test the off on the switch.
Remember when I rewired everything, I didn't really check if the magneto worked.
Wiring of the new switch.
Positive.
Battery.
Negative ground.
Solenoid and magneto.
Only those four wires are connected to the engine.
So it all works.
Works great.
Carburetor needs adjusting because I'm like halfway and it wants to stall.
So I need to do the idle screw a little bit.
Maybe the fuel mixture screw.
And of course, I never clean the carburetor.
I mean, it looked pretty clean, but you never know.
So I didn't really clean it.
When that first start of that muffler went up, tons of this rusted dust flew out.
It's really not that great.
But anyway, pretty stoked.
We still have a lot more to go, trust me.
But now I'll be able to put the hood on here, right?
And then our next episode, we're going to put the hood on.
We're going to put the double stack pulley on here.
But before we do that, I got to pull the mower deck belt out because Nick from Bellport cut it to get the pulley out fast.
And so we need to pull that belt out.
I have to first look at the way it's routed first and remember how it goes.
Pull the belt out.
Try to connect with some duct tape so I know the length.
We go to my shed where I have a lot of mower deck belts and drive belts, and I'll try to get one closest to that size.
We'll reroute it on here, put it on the double stack pulley.
Put the double stack pulley on.
Put the new bolt that I got from Brian and see if it fits.
I hope it fits.
And then we could go for a ride to see if the drive works, right?
And then the mower deck, see if the mower deck works.
And then eventually I'm going to have to go buy a battery because we can't just keep charging this like that.
You know what I mean?
And then we'll try to fix the broken front headlight and connect the lights somehow.
But other than that, I mean, we have an engine that I put together with parts for free.
That's right, free!
Put it on here, and we got the tractor for free.
So far, I haven't spent a dime.
I've got the parts from my friend Brian.
We got parts from Dave as well as Mark, subscribers who contribute parts to the channel.
You see, your parts are being used for projects.
And in turn, you get a shout-out.
So continue to buy my stickers, paypal.me slash mowersandblowers if you guys can donate a buck or two.
And share and like and subscribe to this channel.
We'll see you guys next time on Mowers and Blowers.
See you guys next time on Mowers and Blowers!