Mixed Signal Circuit Design -Sample and Hold Circuit
Oct 6, 2023
Module 5
So today we are going to discuss about the sample and hold circuit
This figure shows a basic sample and hold circuit
If you look at the figure, you can see a MOSFET, a holding capacitor and an op-amp
We are going to apply a narrow pulse to the gate of the MOSFET
When we apply a narrow pulse to the gate of the MOSFET, the MOSFET will start conducting and the hold capacitor will start charging
The width of the pulse applied to the gate of the MOSFET depends on the charging of the capacitor
We have used an op-amp here
An op-amp acts like a buffer, a unity gate buffer
The purpose of the buffer circuit is to isolate the hold capacitor from the external load
The problem of this circuit is that the charge injection and the clock feed through affect this circuit
This figure shows a basic sample and hold circuit
When we apply a narrow pulse to the gate of the MOSFET, the MOSFET will start conducting and the capacitor will start charging
The width of the pulse applied to the gate of the MOSFET depends on the charging of the capacitor
An op-amp acts like a buffer, a unity gate buffer
The purpose of the buffer circuit is to isolate the hold capacitor from the external load
The problem of this circuit is that the charge injection and the clock feed through affect this circuit
This figure shows a basic sample and hold circuit
We have used two amplifier buffers here
Input and output
Some switches are connected here
These are the switches S1, S2 and S3
The purpose of S2 is to ensure that the amplifier A1 is stable in hold mode
If we do not use the S2 switch, the amplifier A1 will be in open loop in hold mode
If the amplifier A1 is in open loop, the gain will be maximized and the amplifier A1 will swing to one of the rails
The purpose of the amplifier A1 is to track the input VIN
The S3 switch is connected in hold mode
When the S3 switch is in hold mode, the amplifier A1 will be disconnected from the output
There are some disadvantages to this sample and hold circuit
As I said earlier, the basic sample and hold circuit affects the charge injection and the clock feed through
In sample mode, the circuit will be unstable
We have to use compensation capacitors to stabilize the circuit
The size and placement of the capacitor depends on the characteristics of the op-amp used in the amplifier
This is a close loop sample and hold circuit using a transconductance amplifier
Here we are using a transconductance amplifier to charge the hold capacitor
The first stage is a transconductance amplifier
The transconductance amplifier is given a voltage called Vcontrol
Vcontrol is used to switch on and off the A1 amplifier
We can eliminate the two switches S2 and S3 used in the previous circuit
CMOS op-amps are used for high output impedance applications
So this sample and hold circuit is a popular sample and hold circuit
But the need of this topology is detected by the maximum current output of the transconductance amplifier and size of the hold capacitor
The need of this topology is detected by the maximum current output of the transconductance amplifier and size of the hold capacitor
The difference is that we are using a transconductance amplifier
The transconductance amplifier is given a voltage called Vcontrol
We can eliminate the two switches S2 and S3 used in the previous circuit
A close loop sample and hold circuit using a transconductance amplifier is shown in figure
Here we have connected a hold capacitor in the feedback path
One side of the hold capacitor is the output of the A2 amplifier
The other side of the hold capacitor is the input of the A2 amplifier
The reason for the virtual ground is that the virtual ground is the property of the op-amp
The difference input of the op-amp is 0
The positive terminal of the A2 amplifier is grounded
The negative terminal of the A2 amplifier is grounded
One side of the hold capacitor is the output of the A2 amplifier
The other side of the hold capacitor is the virtual ground
In this figure, the switch S1 is turned off
Any charge injected on the hold capacitor causes a slight voltage change in the output
One side of the switch is connected to the virtual ground
Therefore, the threshold voltage of the switch is not affected
The voltage change does not depend on the threshold voltage of the switch
Therefore, the charge injection is independent of the input signal
There is an error in the output due to the offset voltage
The non-linearity error can be easily tolerated by the offset voltage
The S1 switch is closed and the S2 switch is open
The equivalent circuit of the low pass filter is a simple low pass filter circuit
The circuit of a low pass filter is a low pass filter or an integrator circuit
S1 is closed and S2 is open, the equivalent circuit works like a low pass filter circuit
and the input is like a low pass filter circuit with a buffered input
we have studied the overall transfer function of a low pass filter
transfer function Vout divided by Vin is equal to minus R2 by R1 into 1 by 1 plus SR2CH
this is the transfer function equation of a low pass filter
this will be a low pass filter function when sampling
if we consider a low impedance circuit, we can eliminate the buffer
when the hold mode is commenced, the output will be held at a constant value

