EC 462 Mixed Signal Circuit Design-CS Stage With Diode Connected Load
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, last class we were discussing about common swiss stage with current swiss load
I hope you all have learnt about common swiss stage with current swiss load
Today we are discussing about common swiss stage with diode connected load
When we learn about common swiss stage with current swiss load
What is the difference between RD and current swiss load?
It is a current swiss circuit
Here also it is a diode connected circuit
Why we are replacing it?
We are replacing RD resistor
This is the circuit diagram of common swiss stage with diode connected load
Common swiss stage diagram is
Here M1 is a transistor
In this portion, in the output side
RD is a resistor
After replacing RD resistor
We are replacing it with M2 transistor
In which configuration that transistor is placed?
It is diode connected
What is it acting as?
It is acting as diode connected load
If a transistor is placed in diode connected configuration
NMOS device is connected as VDD
Gate terminal of NMOS device is connected as VDD
This connection is the RD connection
This is the common swiss stage with diode connected load
This is the equivalent simplified smart signal model of MOS stage using diode connected load
This is the equivalent smart signal stage
In this diagram, we have considered lambda and channel length modulation effect
If we neglect channel length modulation effect
If lambda is equal to 0
You don't have to consider RO1 and RO2 in this figure
If we neglect channel length modulation effect
What will be the equivalent resistance of diode connected load?
It will be 1 by gm2
This is the equivalent resistance of this transistor
Let it be like that
Now let's see why we are using common swiss stage with diode connected load
In some applications, we may use diode connected MOSFET as drain load
In common swiss configuration, we have replaced the RD resistor with diode connected load
Such a topology exhibits only moderate gain due to relatively low impedance of the diode connected device
This is the equivalent of diode connected device
It has relatively low impedance
So, we are using this topology for moderate gain application
For example, if it is lambda is equal to 0, then we are neglecting the effects of channel length modulation
If we neglect it, the resistance of M2 will be 1 by gm2
If we neglect the effects of the channel length modulation,
the internal output resistance of this transistor is R01 and R02
R01 and R02 are the internal resistance of this transistor
The indian resistance of the transistor is neglected if lambda is equal to zero or if the modulation effect from the channel is neglected.
M2 is the equivalent resistance of the transistor.
It is 1 by gm2.
Which one to consider?
We will consider this one.
We have already studied the gain.
In common series configuration, the equation for gain is minus gm into rd.
vout divided by vin is equal to minus gm into rd.
Instead of replacing rd, we are using diode connected load.
Instead of rd, we are using 1 by gm2.
So we can write av is equal to minus gm.
gm is the input transistor.
gm1 minus gm1 into rd is equal to 1 by gm2.
In the last class, I told you that gm1 is the equation of transconductance.
It will be common in all other classes.
So, please keep that in mind.
gm1 is the equation of transconductance.
root of 2 mu n cox into w by l into id.
That is the equation of transconductance.
mu n is the mobility.
cox is the oxide layer length.
w by l is the width to length ratio of a transistor.
id is the drain current.
This is the width to length ratio of a second transistor.
These are the common parameters in this equation.
Gain is equal to minus root of w by l of 1 divided by w by l of 2.
So, this is the equation for gain of diode connected load.
This is the equation for gain of diode connected load.
I have not considered anything in this.
I have not considered channel length modulation effect.
The gain is given by the dimension of m1 and m2 and remains independent of the process parameters mu n and cox and the drain current id.
If we look at this equation, we can realize that the gain depends on the width to length ratio.
Mu n, cox and id are all independent.
The gain depends only on the width to length ratio.
So, which case did we study?
We studied this in the case of MOSFET.
Now, we do not use diode connected load in the common emitter stage.
If it is a MOSFET, we can use diode connected load.
But if we use transistor or BJT, we should not use diode connected load.
Why did we not consider a common emitter stage with a diode connected load?
Let us see.
What is the equation for gain?
Gain is equal to minus gm into rd minus gm into rd divided by gm2.
Similarly, minus gm into 1 by gm2.
In the case of BJT, we study the equation of transconductance in the first year.
Transconductance gm1 is equal to ic1 divided by vt.
We study this equation in the first year.
The equation of gm1 is gm is equal to ic by vt.
ic is the collector current and vt is the thermal voltage.
We have studied the equation of thermal voltage.
KT by E is the equation of thermal voltage.
It is not necessary.
The value of vt is 25 mV.
In the case of BJT, why did we not consider a common emitter stage with a diode connected load?
The equation of gm1 is ic1 divided by vt.
The equation of gm2 is 1 by ic2 divided by vt.
ic1 and ic2 are approximately equal.
They can be approximately equal to minus 1.
This is the fundamental difference between MOSFET and bipolar devices.
The transconductance of MOSFET depends on the device dimension.
But the bipolar BJT does not.
In the case of bipolar BJT, the transconductance of MOSFET does not depend on the device dimension.
This is the reason why we are not using a common emitter stage with a diode connected load.
To get the most accurate equation of this equation, we have to consider the channel length effect.
The channel length effect is zero.
But to get the most accurate value, we have to consider the channel length effect lambda.
That means lambda not equal to zero.
Then which effect will occur?
The effect of RO2 and RO1.
What are the output resistances?
This is one, this is another and so on.
These three resistances are in parallel configuration.
The output resistance is 1 by gm2 parallel RO2 parallel RO1.
This is the output resistance.
If we consider the channel length modulation effect, the output resistance is 1 by gm2 parallel RO2 parallel RO1.
So we can write 1 by gm2 parallel RO2 parallel RO1.
The equation for the gain is equal to minus gm into RD.
Instead of RO, we substitute this value for the output resistance.
Minus gm1 into 1 by gm2 parallel RO2 parallel RO1.
This is the equation for the output resistance.
Minus 1 by gm2 parallel RO2 parallel RO1.
So this is the NMOS common switch stage we used with a diode connected load.
Now we can implement this same thing in PMOS.
Let's see what we do to implement PMOS.
First, convert NMOS device into PMOS device.
Instead of NMOS, we took PMOS-M2 and PMOS-M1.
The diode connected load is VDD.
NMOS is connected as VDD.
PMOS is connected as GND.
This is PMOS-M1.
PMOS-M1 is connected as GND.
Drain is also connected as GND.
This is the only difference when considering PMOS device.
The rest is the same.
The equation for the gain is equal to minus gm2.
The reason for taking gm1 is M1.
Here it is M2.
So we write gm2.
Minus gm2 into 1 by gm1 parallel RO1 parallel RO2.
Small signal modulus is the same equation.
There is no doubt about it.
So, this is all about common switch stage with diode connected PMOS device.
We discussed about common switch stage with diode connected load.
Diode connected means this connection.
Gate is connected as VDD.
In case of NMOS, gate is connected as GND.
Gate and drain is connected as GND.
In case of NMOS, gate and drain is connected as VDD.
Equivalent small signal modulus is used for moderate gain.
This is the reason for low impedance of the diode connected device.
First, we neglected the channel length modulation effect.
When we neglected, we got the equation of gain as minus gm into RD.
Gain equation is minus gm1 into 1 by gm2 which is equal to root of W by L of 1 divided by W by L of 2.
Now, we discussed about the common emitter stage with diode connected load.
Gain equation is minus gm1 into 1 by gm2 which is equal to root of W by L of 1 divided by W by L of 2.
Next, we discussed about the channel length modulation effect.
When we discussed about the channel length modulation effect, we discussed about the effect of these two resistors.
Output resistance is 1 by gm2 which is equal to parallel R0 to parallel R01.
Gain equation is minus gm1 into 1 by gm2 which is equal to parallel R0 to parallel R01.
Output resistance is root is equal to 1 by gm2 which is equal to parallel R0 to parallel R01.
Gain equation is minus gm1 into RD which is equal to root of W by L of 1 divided by W by L of 2.
Now, we discussed about PMOS stage.
In PMOS, we have to pay attention to the input which is M1.
What should we connect to M1?
Gate and drain should be grounded.
Then, it will be diode connected.
After diode connected, the rest of the equations will be same.
These are about common switch stage with diode connected PMOS device.
Hope all of you understand this topic well.
See you in the next class.

