EC 462 Mixed Signal Circuit Design- SOURCE FOLLOWER( EXERCISE/EXAMPLE PROBLEMS)-KTU
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, in the last class we have learnt about the source follower
Today we are going to do two exercises related to the source follower
Let's look at the question
A source follower is realized as shown in figure where M2 serves as a current source
Calculate the voltage gain of the circuit
We have learnt about the circuit of the source follower
Here we have changed the circuit diagram
This is the circuit diagram of the source follower
This is a transistor M1
This is a load called RL in the source
We are taking the output across that load
The input was VIN
The difference in this figure is that
A current source is drawn here replacing this RL
Where M2 serves as a current source
M2 is a current source
What was here before was RL
Replacing that, a current source was drawn
Calculate the voltage gain of the circuit
Let's simplify the circuit for this
Instead of M2, let's put an equivalent resistance
Let's put the output resistance of the transistor
To work as a current source, we have grounded the terminal VB
The output resistance of the transistor will come here
The output resistance of the transistor is RO2
Now the equation for the gain
RO2 is equivalent to the load resistance of the transistor
RO2 is the resistance offered by the transistor M2
The equation for the gain is RO parallel RL
RO parallel RL divided by 1 by gm plus RO parallel RL
Instead of RL, let's put RO2
RO1 parallel RO2 divided by 1 by gm1 plus RO1 parallel RO2
Instead of RL, let's put RO2
Let's replace RO with RO1
Instead of 1 by gm, let's put gm1
That's the difference
The basic equation is very easy
Just replace the equation with RO2
Approximately equal to 1
The gain of the source follower is slightly less than unity
That's why the gain is approximately equal to 1
Let's look at the next question
Here we have given RO as 50 ohms
We have not given RO as the output resistance
If we don't give RO, we can take it as infinity
Since we don't give RO as the output resistance, let's take it as infinity
What was the equation for the gain?
The equation for the gain is RO parallel RL divided by 1 by gm plus RO parallel RL
Here we assumed RO as infinity
The effective resistance of RO parallel RL is 1 by RO plus 1 by RL
1 by RO is approximately equal to 0
1 by effective resistance is 1 by RL
That's why we took it as RO parallel RL
Is it clear?
Similarly, we don't have to consider RO parallel RL
Since the effective resistance of RO parallel RL is 0, we don't have to consider it
Instead, we can rewrite the equation as
AV is equal to RL divided by 1 by gm plus RL
Now, what have we given in the question?
We have given voltage gain as 0.5
We have given AV
Similarly, if we know RL, we have to substitute both the values of RL and AV into this equation
What are the values?
We have given the value of AV as 0.5
We have given the value of RL as 50
When we substitute these two values into this equation, we will get gm is equal to 1 by 50 Ohm
We got the value of transconductance
When we get the value of transconductance, we can find the ratio of width to length
For that, we have to find this equation
What is the equation of transconductance?
gm is equal to root of 2 mu n Cox into W by L into Id
Now, look here
We have given the power budget
Power budget is 10 milli watt
Similarly, we have given the voltage
Voltage Vdd is equal to 1.8 volt
What can we find from this equation?
We can find the value of Id from this equation
We can find the value of drain current from this equation
In this gm equation, we have given the value of root of 2 mu n Cox
When we substitute the value of Id into this equation, we will get W by L is equal to 360
We got the value of width to length ratio from this equation
You can check these two exercises
These questions are related to social followers
Hope you understood these two exercises
See you in the next class
Thank you

