There are many materials that can be used to build a retaining wall. I chose the cheaper route by using 2x10 and 2x6 ground contact treated pine. I left off a few steps that I didn't feel were necessary for this build. I did not included a drain pipe behind my wall and I did not use cement to fill the holes for my support posts. Please let me know if you have any questions about the build.
Use these Amazon Links to order some of the items used in this video.
*My description includes referral codes/links that allow me to earn points or credit that can be redeemed for products and/or subscriptions. When you use my referral code/link, you are helping to support me and my recommendations! Thank you for your support!*
Welcome back guys, it's the Tightwad and I have another project in my lawn. I'm
replacing a retainer wall. The previous material was this landscaping timbers, the
little, I think they're called 3x4 landscaping timbers, and I actually got
them used from a retainer wall that was being torn down and I was short on cash
at the time and about to have a baby, so we used these to build our retainer
walls and they are rotting after about five years. We're going to replace this
also, but I wanted you to see what we started with so it's the same process up
there as we have down here, but this one's in better shape than the one up
there is. These are the remnants of the landscape timbers that I removed, so this
is the old wall. You can see I used rebar to hold it in place. There were some
landscape timber spikes in them and all in all they just rotted, decomposed over
time, and I ripped them all out and we're going to replace them. It's not really
load-bearing, but you can see where the wall used to be. I have recovered as much
gravel as possible from the previous retainer wall and I will be replacing it
with 2x10s supported by 2x6s and some 2x10x8s and 2x10x12s here
for the various lengths that I have, and I'm going to show you guys the best way
to do this. This is ground contact rated lumber, meaning it's not just pressure
treated, but it is rated for ground contact so it can be directly against
the dirt, and they say it lasts up to 30 years. I give it more like 10 years, but
it does work a lot better than what you would typically build your deck with. So
I'm going to show you guys the process that I'm going to go through. It is not
exactly what a contractor would do. They would probably use 6x6s on this
area, but the price difference was about $300. So I'm going to do it with 2x10s
since it's non-load-bearing, well semi-non-load-bearing, and I will show
you my process. Alright, I'd like to explain the progress so far. I have 3
foot tall 2x6s and 2x4s. This is the corner, so it's joined at a right
angle and put in with screws here. These are coated screws made for decking so
they can handle the treatment that has been done to the treated wood, the
ground contact treated wood, because they have a coating on them. I actually found
them for 50% off at Home Depot because they were green instead of brown and
they switched to brown. But I have 2x6s, 2x4s, and 2x8s here, and these
are sunk into the ground 16 inches with gravel packing them in. This one's not
fully filled yet, but it will be. And then I have the 2x8s screwed to the back of
these boards, and I'm going to move down and show you the next section. So the
next section is a 2x6 and a 2x4. On this one, I cut the 2x4 at an angle and
the same with the 2x8s. I have this 2x4 running on the top of this so I
can show you the progression. So right here I have my level, 4 foot level,
laying across a board that I know is straight, making sure that that post and
this post are the same height. This is the same process I did on the other end.
I then take a shorter level, a little 2 foot level, and I make sure that the
boards and the ground are level up and down in both directions. You can use a
torpedo level if you have one. I don't have one of those right handy so that
I'm just using my 2 foot level, and these boards are long enough that it
doesn't make any difference. And I've got this one already packed in and ready
to go. We'll go ahead and move down to the next one. This will again be a corner.
You can see I just have the 2x6 loose here. I will attach a 2x4 to it after
cutting an angle like I did on the other end. It was a 70 degree angle, and I will
sink those two down in here and make sure that they're level with the other
posts. And then on the corner, I'll have another 2x6 and 2x4 joined at a 90
degree angle. One thing that you'll note is that in the trough where the boards
are sitting, there's gravel all the way down. There's actually gravel behind the
existing retainer wall. You can see it's still embedded in the walls here, and as
that spilled out, I collected as much as I could in buckets and on this tarp
because I will then backfill the wall with this once I'm done. I'm probably
going to have to get some more gravel to backfill the wall, but having gravel
between the dirt and the wall helps prevent moisture from sitting on the
back of the wall. So you see there's a cavity on the back of this wall that
will be filled in with gravel. It has landscape fabric to keep the dirt or
soil from coming through into the gravel. Keeps the gravel nice and clean, and the
gravel drains well. So it drains down behind the wall and under the wall
instead of getting trapped behind it and causing rot. Alright, I'm finished with
the wall, and you can see that I ended up adding some extra boards here. They're
not braces into the ground, but they're braces to hold the two boards from
bulging out or separating. And I also added a deck board across the top. It's just a
six inch deck board all the way down in case we want to come out and sit on it.
I'll get a new pine straw spread in a couple of weeks to get ready for spring,
and I think it turned out really well. This is not going to be a how-to video,
just a here's what I did video. I'm not a professional on this. I cut some corners
on a couple of things. You can critique if you want, but just know that this is
not considered a how-to video, but I think the end result looks pretty nice.
If you like this video, give me a thumbs up. If you have any questions about
anything I did, feel free to leave them in the comment section below. Please
subscribe to my channel as I do more home projects around my home, and I hope
you guys have a great day.