BIASED CLIPPER || ECT202 ANALOG CIRCUITS || EC205 || ECT 281 ELECTRONIC CIRCUITS || KTU
This video explains Non linear wave shaping circuit-Clipper (part 2)- biased Clipper
This topic is also in the syllabus for
1. ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
2. CS 207 Electronic Devices and Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmh9Royg7s7B78IiWpou-lE0
3.ECT 281 Electronic Circuits ( Minor): https://youtube.com/playlist?list=PL2UV2EJdMQmiduKsGRgNFuu_MqB__HVpN
#circuits #ktu #ece #electroniccircuits
Hi all, in the last class we have discussed about Clippers
We have classified Clippers as
Unbiased Clippers
and Biased Clippers
Biased Clippers
Unbiased Clippers does not provide
any external biasing
or any external DC voltage
At the same time
Biased Clippers provide external DC voltage
to the circuit
That is the difference between Biased Clippers and Unbiased Clippers
In the last class we have discussed about
Unbiased Clippers
and Positive Clippers and Negative Clippers
Today we are discussing about Biased Clippers
There are different types of Biased Clippers
Positive Clippers, Negative Clippers, Combined Clippers
Positive Clippers
remove the positive part of the sine wave
Positive Clippers retain only the negative part of the sine wave
Negative Clippers
remove only the positive part of the sine wave
Combined Clippers
remove only the positive part of the sine wave
Slicer Clippers
remove only one part of the sine wave
Slicer Clippers
remove only one part of the sine wave
Biased Clippers
remove only one part of the sine wave
Let's see the details of Positive Clippers
Positive Clippers are used to clip
the input signal above a certain level
When we studied positive clipper in unbiased case, the circuit diagram we drew was like this.
This was the circuit diagram of a positive clipper.
What should we add to this circuit diagram?
We just need to make it biased.
We add an extra DC supply here.
What is special about adding this DC supply?
When we add VR DC supply, we need to make sure that this DC supply will reverse bias this diode.
To reverse bias the diode, the positive of this DC supply should be in the negative of the diode.
Only then it will reverse bias this diode.
In that case, the cut-in voltage of this diode should be V gamma to conduct the diode.
We have reversed biased this diode with an external DC.
We need to overcome that reverse bias.
That reverse bias is called VR voltage.
Only when V gamma plus VR voltage is reached, this diode will be forward biased.
If this diode is always forward biased, the diode has a cut-in voltage.
The cut-in voltage of the diode is V gamma.
Moreover, we have reversed biased this diode with VR voltage.
We need to overcome that reverse bias.
Only when VR plus V gamma is greater than VR plus V gamma, the diode will be forward biased.
Only when VR plus V gamma is greater than VR plus V gamma, the diode will conduct.
This is the equation of output voltage.
In the previous class, we discussed the value of the voltage when the diode is forward biased.
The equation is Vout is equal to Vo is equal to V gamma plus Vi minus V gamma into RF divided by Ri plus RF.
Here, the equation is V gamma plus Vi minus V gamma into RF divided by RF plus R.
This is the equation.
In this equation, we are adding a voltage called VR.
The output will have the same effect.
The equation of output is VR plus V gamma instead of V gamma.
Earlier, there was only V gamma.
Here, it is VR plus V gamma plus Vi minus of VR plus V gamma into RF divided by R plus RF.
If we rewrite this again, we can write it like this.
If we open the bracket, we can write it like this.
The diode conducts in the positive half cycle.
When we take the waveform, it will be positive in the positive half cycle.
Here, it will be negative.
The positive voltage will increase.
Only when the positive value is greater than VR plus V gamma.
When the positive value is greater than VR plus V gamma, the diode will conduct.
When the diode conducts, it will act like a short circuit.
Then, the output will be minimum.
Then, the output voltage will be in the positive half cycle.
The negative half cycle will be the same.
In the negative half cycle, the diode will be an open circuit.
In the open circuit, the output follows the input.
The diode will be an open circuit.
In the negative half cycle, the output will follow the input.
In the negative half cycle, the output voltage and input voltage will be the same.
Here, RF divided by RF plus R is the transfer characteristics.
The output and input characteristics are the transfer characteristics.
The V out and V input characteristics are the transfer characteristics.
The RF divided by RF plus R is the slope of the transfer characteristics.
VI is less than VR plus V gamma.
VI is the input voltage.
When it is less than VR plus V gamma, it will act like an open circuit.
Then, the output will follow the input.
This is the waveform.
In the positive half cycle, the positive half cycle of the input will be positive.
Here, positive.
Here, negative.
Here, positive.
Here, negative.
Here, positive.
Here, negative.
Here, positive.
Here, negative.
Here, positive.
Here, negative.

