UNBIASED CLIPPER || ECT202 ANALOG CIRCUITS || EC205 || ECT 281 ELECTRONIC CIRCUITS || KTU
This video explains Non linear wave shaping circuit-Clipper (part 1)- Unbiased Clipper
This topic is also in the syllabus for
1. ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
2. CS 207 Electronic Devices and Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmh9Royg7s7B78IiWpou-lE0
3.ECT 281 Electronic Circuits ( Minor): https://youtube.com/playlist?list=PL2UV2EJdMQmiduKsGRgNFuu_MqB__HVpN
#circuits #ktu #ece #electroniccircuits
Hi all, today we are discussing about non-linear wave shaping circuits.
We have categorized linear wave shaping circuits and non-linear wave shaping circuits as wave shaping circuits.
In linear wave shaping circuits, we have Rc circuits.
We have studied Rc high pass circuit and Rc low pass circuit.
We have studied different responses of square wave, step input, integrator and Rc differentiator.
So today we are discussing about non-linear wave shaping circuits.
What is the difference between linear wave shaping circuits and non-linear wave shaping circuits?
In the case of non-linear wave shaping circuits, we are using active components along with passive devices.
We are using diode as an active component along with resistors and capacitors as passive devices.
Non-linear wave shaping circuits are such circuits.
We can categorize non-linear wave shaping circuits as clipper and clamber.
Clipper and clamber are the two types of non-linear wave shaping circuits.
What is clipper and clamber?
Today we are discussing about clipping circuits.
Clipping circuits are used to clip off a part of input waveform.
Clipping circuits are also called amplitude limiters.
If we consider a sine wave, clipping circuits are used to clip off a portion of the input waveform.
Clipping circuits are used to clip off a portion of the input waveform.
Clipping circuits are also called amplitude limiters.
There are two categories of clippers.
Series clipper and parallel clipper.
The main component of clipping circuits is diode.
If the diode is connected in series,
if the load is connected in series,
if the load is connected in parallel,
then it is called parallel clipper or shunt clipper.
Series clipper and parallel clipper are the two categories of clipping circuits.
Series clipper is connected in series with the load.
Parallel clipper is connected in parallel to the load.
If the circuit is used to clip at voltage level equal to cut-in voltage of the diode,
it is called unbiased clipper.
Unbiased clipper is used to clip at a voltage level equal to cut-in voltage of the diode.
Unbiased negative clipper is used to clip at a voltage level equal to cut-in voltage of the diode.
Positive half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Negative half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Positive half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Negative half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Positive half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Negative half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Positive half cycle of the sine wave is used to clip at a voltage level equal to cut-in voltage of the diode.
Vout is equal to Vgamma plus Vi minus Vgamma into Rf divided by R plus Rf.
Vout is equal to Vgamma plus Vi minus Vgamma into Rf divided by Rf plus Rf.
In negative half cycle, output follows the input.
For all other input conditions, the diode is reverse biased and it behaves like an open circuit. Hence, output follows the input.
Vout assumes to be an ideal with Vgamma is equal to 0 and Rf is equal to 0.
Rr is the reverse resistance of a diode. Rr is equal to infinity.
Vout is equal to Vgamma plus Vi minus Vgamma into Rf plus Rf.
That's all about unbiased clippers.
In the next class, I will explain about biased clippers.
Thank you. See you in the next class.

