MID FREQUENCY ANALYSIS OF CE AMPLIFIER WITH BYPASS CAPACITOR || ECT202 ANALOG CIRCUITS || KTU
Topic Covered
1. AC equivalent model
2. Hybrid pi model at mid frequency
3. Small signal analysis
For full class
ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
#circuits #ktu #ece #electroniccircuits
Hi all, today we are discussing the mid-frequency analysis of a common emitter amplifier using hybrid pi model.
We have studied the frequency response in the case of a RC coupled amplifier or common emitter amplifier.
How was the frequency response?
This figure shows the frequency response in the case of an RC coupled amplifier.
In this figure, we can see that the gain in the low frequency region is less,
the gain in the high frequency region is also less,
and the gain in the middle frequency region is almost constant or maximum.
We have studied that the reason for the low frequency gain in the region is the effect of the coupling capacitor and the bypass capacitor.
We have studied that the reason for the low gain in the high frequency region is the effect of the junction capacitor in the transistor.
The gain in the middle frequency region is constant or maximum.
We can say that there is no effect of the bypass capacitor and the junction capacitor in the middle frequency region.
This is the frequency response.
Today we are discussing the analysis of this region.
This is the analysis of the mid-frequency region.
This is the mid-frequency region.
We are doing this analysis today.
The mid-frequency analysis is done here using the hybrid pi model.
Let us see how the mid-frequency analysis is done.
There are some steps to do mid frequency analysis.
The first step is, we have to draw the equivalent circuit diagram, equivalent AC model of this circuit.
After drawing the AC equivalent model, we replace the transistor in the AC equivalent model with the transistor's small signal model.
The small signal equivalent is a hybrid pi model, corresponding to the transistor.
The third step is, after doing this, we have to analyze the circuit.
After analyzing the circuit, we find out the corresponding input resistance, voltage gain, current gain and output resistance.
So, we are doing these three steps.
The first step is, we draw the AC equivalent model and replace the transistor with its small signal equivalent.
The third step is, we do its analysis.
We are doing mid frequency analysis.
So, let's look at the first step.
The first step is, draw the equivalent model.
How do we draw an equivalent model?
The first step to draw the DC equivalent model is, short circuit all DC sources.
The DC source here is VCC.
What do we connect to VCC?
We connect the ground or short circuit VCC.
To short circuit VCC,
VCC is actually connected like this.
Here, a DC source with plus or minus is grounded like this.
This point is connected to this point.
If we short circuit this,
if we connect it like this,
what happens to this DC source?
It becomes ground.
The first step is, short circuit DC sources.
Why do we replace VCC?
We replace it with ground.
The first step is, why do we replace VCC?
We replace it with ground.
The second step is, short circuit all capacitors.
The capacitors in this,
the capacitor called CC,
and the next capacitor called CE,
what do we have to do for all these?
We have to short circuit them.
We short circuit these three capacitors.
What do we mean by short circuit?
If we short circuit this,
the effect of the capacitor does not come here.
We can simply redraw it like this.
The capacitor goes from here,
the capacitor here is removed,
and all these three capacitors are short circuited.
Now we are redrawing this circuit diagram.
Before redrawing,
the thing to note is,
like VS and RS,
R1 and R2 are parallel combinations.
We can redraw it by moving it down.
For example,
R1 is in the middle of which?
R1 is across the transistor base and ground.
The common point between the base and ground is ground.
We can redraw R1 by moving it down.
I have taken R1 here.
Now let's look at RE.
RE is R1, R2 and RE.
Will the effect of RE come?
The reason is,
the emitter terminal is short circuited and grounded.
When we replace it with a short circuit,
the emitter terminal is directly connected to ground.
Then what can we remove?
We can remove the RE resistor from here.
So our diagram is like this.
We have removed the RE resistor.
Now let's look at RC.
RC is located at the collector terminal of the transistor and across the ground.
RL is also located at the collector terminal of the transistor and across the ground.
We can redraw RC by moving it up.
We have removed the RC resistor.
Now let's look at the next step.
Here, R1 and R2.
Both R1 and R2 are across the transistor base and ground.
These two resistors are a parallel combination.
So we can effectively replace these two resistors with a single resistor.
If I replace the single resistor with a resistor RB,
I get RB is equal to R1 parallel R2.
I am replacing these two resistors with a single resistor RB.
So RB is equal to R1 parallel R2.
For that, I am going to represent these two resistors with an equivalent RB.
So the first step is done.
The AC is an equivalent model for mid-frequency analysis.
Now what is the second step?
In the second step, we are going to replace this transistor with the equivalent model of the transistor.
Before mid-frequency analysis, we studied the hybrid pi model.
We developed a model for mid-frequency analysis using a hybrid pi model.
We are going to replace the transistor with this model.
We replace transistor by its equivalent model.
When we redraw the circuit, we replace the transistor with the equivalent model.
This is the input resistance of the transistor, Rpi.
This is the current source of the transistor, Vpi.
This is the output resistance of the transistor, R.
We are going to replace the transistor with this model.
Now let's draw the small signal model.
For that, we have drawn the Vs and Rs in the same way.
Then we have drawn the RB in the same way.
RB is the base and ground of the transistor.
Now, we are going to replace the transistor.
We are going to replace the transistor with the small signal model.
We are going to draw the small signal model which is equivalent to the transistor.
We have drawn Rpi in the same way.
We have drawn Vpi of the gm in the same way.
We have drawn Rho in the same way.
This is the transistor.
This is the base of the transistor.
This is the base.
This is the collector.
This is the emitter.
The emitter terminal is grounded.
So, we can ground the emitter terminal.
RB is connected to the emitter terminal.
We have drawn the transistor.
RC is the collector and ground of the transistor.
Since the emitter is grounded, RC is the collector and ground of the emitter.
RC is the collector and ground of the emitter.
RL is the collector and ground of the emitter.
This is how we draw the small signal model.
We have done the full analysis based on this.
Now, let's go to the third step.
The third step is analysis.
There are some factors to be found in analysis.
The factors to be found are
Input resistance,
Output resistance,
Output resistance of the amplifier,
Voltage gain,
Current gain.
These are the factors to be found in analysis.
Let's look at them one by one.
First, let's find the input resistance.
The first factor to be found is input resistance.
This method has to be used to find input and output resistance.
To find input resistance,
we need to exclude the source resistance and look inwards.
We need to look outwards from the input side.
This is what we call input resistance.
What we need to do to find the output resistance is
to exclude the load resistance and look inwards.
This is what we call output resistance.
Let's see why we should exclude the source resistance
So, from the diagram, input resistance R i is equal to R pi parallel to R i.
R b is the equivalent of R 1 parallel R 2.
R b is the equivalent of our voltage divider.
The second thing we are going to find is the voltage gain.
Voltage gain.
Voltage gain or it is denoted as AV.
Now, we are going to find the voltage gain.
What is voltage gain?
Generally, gain is output divided by input.
Similarly, we can do the equation of voltage gain.
Vout divided by Vinput is known as voltage gain.
If we know the output and input, what can we find?
We can find the voltage gain.
The output voltage of this circuit is the output voltage.
We can write the output voltage as output voltage is equal to output current into output resistance.
Isn't that what output voltage is?
We know what is the current flowing through this.
We know that current is gm into V pi.
Current is gm into V pi.
Current into resistance.
Effective resistance is known as voltage.
Instead of current, we can write gm into V pi.
Now, resistance.
Current into effective resistance.
Effective resistance is known as RO parallel RC parallel RL.
These are all parallel combinations.
Effective resistance is known as RO parallel RC parallel RL.
So, output voltage is equal to gm into V pi into RO parallel RC parallel RL.
The direction of current is given here.
The arrow mark is downwards.
That means the direction of current is downwards.
That means the output is coming from this terminal.
But current is flowing in the opposite direction.
So, we have to give a negative mark here.
Since the direction of current is in the opposite direction, we have to give a negative mark here.
Now, input voltage.
Input voltage is the input voltage of the transistor.
The input voltage of the transistor is V pi.
Input voltage is V pi.
Now, gain.
Gain is equal to output divided by input.
So, minus gm V pi into RO parallel RC parallel RL divided by V pi.
Both V pi and V pi get cancelled.
So, we get the gain equation like this.
Av is equal to minus gm into RO parallel RC parallel RL.
So, this is the equation for voltage gain.
Here, gm is the transconductance.
We have studied the equation of gm.
We have studied the small signal model when I explained it.
gm is equal to beta by R pi or alpha by Ri.
It may be useful for solving problems.
So, note this.
The equation of gm is beta by R pi or alpha by Ri.
When we derive it like this, we have not considered the source resistance.
If we consider the source resistance, we can change the equation of gain.
Let us see the difference.
If I consider the source resistance,
I have taken input voltage Vi as V pi.
What is the voltage V pi?
V pi is equal to.
V pi is the voltage coming here.
If we consider the source resistance,
we have to find the voltage division rule here.
Main voltage into resistance in this branch divided by total resistance.
That is called voltage division rule.
Main voltage is Vs into resistance in this branch.
Effective resistance in this branch.
Effective resistance in this branch is a parallel combination of RB and R pi.
RB parallel R pi is taken as input resistance Ri.
Vs into Ri divided by total resistance.
Total resistance is Rs plus Ri.
If we consider the source resistance,
we can change the equation of gain.
How does it change?
When we consider the source resistance,
we have to find V pi.
V pi is equal to main voltage into effective resistance divided by total resistance.
Main voltage Vs into effective resistance is Ri.
Resistance in this branch.
Ri divided by total resistance is Rs plus Ri.
Vi is equal to Vs into Ri divided by Ri plus Rs.
Vi divided by Vs is Ri by Ri plus Rs.
Vi by Vs is equal to Ri divided by Ri plus Rs.
I am rewriting the equation.
Vi by Vs is equal to Ri divided by Ri plus Rs.
Gain considering source resistance is Av of S.
Voltage gain considering source resistance is Vout divided by Vs.
Gain considering source resistance is Vout divided by Vi.
Overall gain is Vout divided by Vs.
Av of S is Vout divided by Vs.
Av of S is equal to Vout divided by Vs.
Vout divided by Vi into Vi divided by Vs.
When Vi and Vi cancel, we cannot write Vout by Vs.
Vout divided by Vi is equal to Av.
Av into Vi by Vs is equal to Ri divided by Ri plus Rs.
Av is equal to minus dm into Ro parallel Rc parallel Rl.
If we consider the source resistance, we have to multiply the gain by Ri divided by Ri plus Rs.
Next, we are going to find the output resistance.
To find the input resistance, we have to find the source resistance.
To find the output resistance, we have to find the load resistance.
When we look inside the load resistor, we can see Rc and Ro.
These two resistors are parallel.
So, we can write Rc parallel Ro.
So, this is the equation for output resistance.
Output resistance Ro is equal to Rc parallel Ro.
The reason for not getting the output resistance is,
we are looking at the output resistance from the output terminal.
When we find the output resistance, we have to ground the input voltage.
When we find the output resistance, we consider Vs as zero.
When Vs is zero, we have to short-circuit Vpi.
We have to short-circuit the input terminal to find the output impedance.
Then, Vpi is zero and Vpi of gm is also zero.
When we look at the output terminal, we have two resistors, Rc and Ro.
So, we can write Rc parallel Ro as output resistance.
Next, we can find the current gain of the circuit.
Current gain or Ai.
Ai is the current gain.
From the equivalent circuit, the current gain Ai is
output current divided by Io divided by input current or Ii.
Current gain is the ratio of output current and input current.
Io is output voltage divided by output resistance.
Output resistance is the load resistance.
This is Io.
Io is the current flowing through the load resistor in the output.
Io is output voltage divided by output resistance.
Io is equal to Vo divided by RL.
Input current or Ii is input voltage divided by input resistance.
Ii is input voltage divided by input resistance.
Current gain is Vo divided by RL whole divided by Vi by Ri.
Current gain is Vo divided by Vi into Ri by RL.
What is Vo divided by Vi?
Vo divided by Vi is the voltage gain.
We can write the equation of current gain as
Current gain is equal to Av into Ri by RL.
This is what we did for the analysis.
First, we drew the circuit diagram of the common emitter amplifier.
Then, we replaced it with AC equivalent.
Then, we replaced the transistor with its equivalent small signal model.
We got the small signal model of the amplifier.
Now, we are going to do the analysis of this model.
We have to find the voltage gain, current gain, input impedance and output impedance.
This is the mid frequency analysis.
This is the mid frequency analysis of a common emitter amplifier.
Next, we are going to do the analysis of a common emitter amplifier without a bypass capacitor.
We will do that in the next class.
I hope you understood today's class.
See you in the next class.

