HOW TO DRAW AC EQUIVALENT OF BJT AMPLIFIER || ECT202 ANALOG CIRCUITS || KTU || Module 2
For full class
ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
#circuits #ktu #ece #electroniccircuits
Hi all, we did a small introduction of AC response in the last class.
We discussed about the AC response of a circuit amplifier.
We have to do two steps.
First, we have to draw the AC equivalent circuit diagram of the amplifier.
Then, we have to replace the transistor in the AC equivalent circuit diagram with the equivalent transistor model.
This is the two steps.
Then, we replace the transistor and draw the small signal model.
We do the rest of the analysis using that model.
So today, I will explain how to draw AC equivalent circuit.
To simplify this circuit, there are three steps.
We have to consider three steps.
First step is to short-circuit all DC sources.
Second step is to short-circuit all capacities.
Third step is to redraw the network by removing all the elements which are short-circuited in step 1 and step 2.
So, these are the three steps to draw AC equivalent circuit of BJT.
Let's see the steps one by one.
First step is to short-circuit all DC sources.
Here, the DC source is Vcc.
So, I have to short-circuit this Vcc.
First step is to short-circuit all DC sources.
So, we have to replace the DC source with ground.
We have to replace the DC source with ground.
Now, I will separate the ground.
Here, the positive of the DC source is connected as Vcc.
The positive of the DC source is connected as negative terminal to R1 and Rc.
This is the short-circuit method.
Instead of Vcc, we can replace the DC source with a ground.
Now, let's see step 2.
Step 2 is to short-circuit all capacities.
We have to short-circuit all the capacities used in this.
When we draw the AC equivalent circuit diagram,
we have already seen the reason for replacing the capacitor.
The reason for replacing the capacitor is the reactance Xc.
Xc is equal to 1 by 2 pi fc.
We are taking large value capacitance values.
In the case of AC, the frequency is 50 Hz.
In the case of large value capacitance, the value of Xc is approximately equal to 0.
0 means reactance or reactance of capacitance.
If the resistance 0 offered by the capacitor is 0,
the capacitor behaves like a short-circuit.
So, we can replace the capacitance with a short-circuit.
I am replacing each capacitor with a short-circuit.
I have short-circuited both Cb and Cc.
Now, let's redraw the short-circuit.
I have short-circuited both Cb, Cc and Ce.
You can see that I have short-circuited the resistor Re.
If the short-circuit is given, all the current flows through Ce.
So, we don't need Re here.
We can replace Re with a short-circuit.
The circuit diagram has these two conditions.
Short-circuit all DC sources and short-circuit all capacitance.
The circuit diagram is in this form.
Now, let's go to the third step.
The third step is to redraw the network by removing all the elements which are short-circuited in step 1 and step 2.
Let's redraw the entire circuit.
For redrawing, we can use the same Vs and Rs.
This R1 goes to the ground like this.
We can move this R1 down.
Let's redraw it like this.
This R1 goes to the ground like this.
R1 and R2 are two parallel combinations.
We can replace R1 and R2 with a resistor RB.
RB is R1 parallel R2.
We can replace R1 and R2 with a resistor RB.
RB is R1 parallel R2.
We replaced R1 and R2 with a resistor RB.
We can move this RC down.
RC is the ground and collector point.
These are the steps to obtain AC equivalent circuit of BJT.
This is how we draw the AC equivalent circuit diagram of a common emitter amplifier.
This is the final equivalent circuit diagram of a BJT amplifier.
I hope you understood how to draw an AC equivalent circuit diagram of a BJT amplifier.
See you in the next class.

