MID FREQUENCY ANALYSIS OF CE AMPLIFIER WITHOUT BYPASS CAPACITOR || ECT202 ANALOG CIRCUITS || KTU
Topic Covered
1. AC equivalent model
2. Hybrid pi model at mid-frequency
3. Small signal analysis
4. Calculation for input resistance, output resistance, voltage gain, current gain
For full class
ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
#circuits #ktu #ece #electroniccircuit
Hi all. In the last class, we studied the mid frequency analysis of a common emitter amplifier.
The difference between a common emitter amplifier and a common emitter amplifier is that,
we have given a bypass capacitor parallel to the emitter resistor RE.
In this circuit, we have avoided the bypass capacitor.
The mid frequency analysis of a common emitter amplifier with unbypassed emitter resistance
means, we have not given a bypass capacitor parallel to the emitter resistor RE.
In this way, there will be a lot of changes in the analysis of the circuit.
Let's see how the mid frequency analysis of a common emitter amplifier works.
In order to do the mid frequency analysis of this circuit,
we need to remember the steps we took to do the small signal analysis.
First, we need to draw the AC equivalent.
Then, we need to replace the transistor in it with a small signal model.
After that, we move on to the analysis.
We can go step by step.
First, we draw the corresponding AC equivalent.
There are some steps to draw the AC equivalent.
The first step is to short circuit the DC sources.
The second step is to short circuit the capacitors.
The third step is to redraw this diagram.
These are the steps.
Today, we are not going to draw the AC equivalent circuit in detail.
Because we have been drawing the AC equivalent circuit for a long time.
So, let's assume that everyone is familiar with it.
The first step is to short circuit the DC sources.
I am short circuiting the DC source.
The next step is to short circuit the CV and CC capacitors.
The second step is to short circuit the CV and CC capacitors.
I have short circuited the CV and CC capacitors.
I have split the common ground.
R1, Vs, Rs, R1, R2.
R1 is the base of the transistor and the ground.
We have to draw the ground.
This is the ground.
This is the common emitter configuration.
This is the ground.
R1 is the base of the transistor and the ground.
We can bring R1 down.
We can draw R1 as a resistor.
This is R1.
We have drawn R1 as a resistor.
R1 and R2 are parallel.
We have been dealing with these equivalents for a few days.
R1 and R2 are parallel.
R1 and R2 are denoted by RB.
RB stands for R1 Parallel R2.
R1 Parallel R2.
Instead of R1 and R2, we replace R1 with RB.
RC stands for transistor collector and ground.
This is the AC equivalent circuit diagram.
The next step is to redraw the transistor with its small signal equivalent.
We know the small signal equivalent of a transistor.
There is a resistor on the input side.
This resistor is called Rπ.
There is a current source on the output side.
The current source is called Gm into Vπ.
There is an output resistance called Ro.
This is the hybrid pi model of a transistor.
Instead of replacing the transistor in the AC equivalent, we are drawing the hybrid pi model.
Let's start drawing.
First, let's draw the Vs.
We draw Vs.
After Vs, we draw Rs.
We draw Rs.
After Rs, we draw Rb.
We draw Rb.
The next step is to draw the transistor.
Instead of the transistor, we draw this diagram.
This is the input resistance of the transistor.
This is Rπ.
This is the current source on the output side.
The current source is called Gm into Vπ.
This is the output resistance of the transistor.
This is the transistor.
This is the base of the transistor.
This is the base.
This is the emitter of the transistor.
This is the collector of the transistor.
We have to pay attention to one thing.
The emitter has been bypassed.
The emitter and the ground were one.
The emitter terminal has not been bypassed.
So, what is connected to the emitter?
There is a resistor called Re in the emitter terminal.
We have to show the resistor called Re.
What will we draw in the emitter terminal?
We have to draw the resistor called Re here.
We have to draw in the emitter terminal of the transistor.
What will come in the emitter terminal?
The resistor called Re will come.
We have drawn the transistor.
Now, look at this.
What is the RC across the transistor collector and ground?
This is the transistor collector.
This is the collector and the ground.
This is the ground.
If we draw like this, the circuit will go wrong.
So, what can we draw across the collector and the ground?
We can draw the resistor called RC.
What is the output resistance of the transistor?
We can draw the load resistor of the circuit.
We can draw the resistor called RL.
Now, look at this.
All these points are common, right?
This point of Vs, this terminal of Rb, this terminal of Re,
this point of Rc and this point of RL.
All these are one terminal.
That is common to ground.
We can draw all these as one ground line.
So, this is the small signal model when the bypass capacitor is not used.
This is the common emitter configuration.
Can you see the difference?
When the emitter resistor is used, the small signal model is completely different.
Now, we have to perform the analysis using this circuit.
Let's go to the analysis.
Before doing the analysis, we can mark a few things.
The first one is the input voltage.
The input current flowing through this can be marked as Ii.
The current flowing through this can be marked as Ib.
Then, the input resistance.
Where do we look for the input resistance?
From this input terminal down here, right?
What do we look for from here?
We look for the input resistance.
Likewise, what do we look for the output resistance?
After removing the load resistor, what do we look for from here?
We look for the output resistance.
All these were mentioned last day.
Now, the input voltage is from here to here.
The input voltage is the voltage flowing from the transistor base to the ground.
This input voltage is the voltage that goes to the whole transistor.
This voltage can be written as Vπ.
This voltage is the Vπ voltage that goes from the transistor base to the emitter.
The Vπ voltage is the voltage that goes from the Rπ resistor to the emitter.
The output current is called I-O current.
Input current is I-B.
The voltage across the arp is V-pi.
Total voltage is V-I.
Input resistance is R-I.
Output resistance is R-O.
Now we can analyze each one.
Input resistance, output resistance, voltage gain, current gain.
First, let's find the input resistance.
How to find the input resistance?
Input resistance can be written as R-I.
Input resistance is the resistance coming in from here to here.
If I take this resistance from here to here as R-I',
the input resistance can be written as R-B parallel with R-I'.
Input resistance is the resistance coming in from here to here.
Input resistance is R-B.
Input resistance can be written as R-I'.
R-I' is where R-I' is equal to.
R-I' is the total voltage divided by current.
The current flowing to this is I-B.
R-I' is equal to V-I divided by I-B.
R-I' is the total voltage divided by current.
The total voltage divided by current means,
the total voltage is dropping here.
It is dropping across Rπ and across R-I.
Let me say it again.
The total voltage, V-I, is dropping across Rπ and across R-I.
I can write V-I' as V-I is equal to V-I by I-B is equal to.
The voltage dropping across Rπ is Vπ.
How can we write Vπ?
We can write the voltage as I-B into Rπ.
The drop across Rπ is I-B into Rπ.
The drop across R-I is I-B into R-I.
How much current is there?
I-B is coming through Rπ to R-I.
The collector current, Vπ, is coming to the emitter.
The emitter current is equal to the base current and collector current.
The current, I-B, is flowing through R-I.
Similarly, the current, Vπ, is flowing through R-I.
In this case, the current, I-B, is flowing through R-I.
The current, Vπ, is flowing through R-I.
The current, I-B, is flowing through R-I.
We got the input voltage.
The input voltage is going here and here.
These two are split.
We can write the whole divided by I-B.
Now, which is equal to I-B, Rπ, plus I-B, R-E, I-B, R-E, plus G-M, Vπ, R-E.
This is multiplied inside.
Now, instead of Vπ, we can write I-B into Rπ.
Instead of Vπ, we can write I-B into Rπ.
So, the equation will change like this.
I-B, Rπ, plus I-B, R-E, plus G-M, into
Instead of Vπ, we can write I-B, Rπ, divided by R-E.
The whole divided by I-B.
In total, we can divide by I-B.
Now, we know that G-M is equal to β divided by Rπ.
So, instead of G-M into Rπ, we can substitute β.
So, the equation will change like this.
Which is equal to Rπ, plus R-E, plus β, R-E.
From these two equations, we can get R-E.
So, we get Rπ, plus R-E, into R-E, plus β.
Now, what do we have to find?
We have to find R-I.
So, we can write the equation of R-I like this.
R-B parallel, R-π, plus R-E, into 1 plus β.
So, this is the equation for input resistance.
Till now, we have found the first thing.
We have found the input resistance that we have to find first.
Now, let's go to the next analysis.
The next thing we are going to find is voltage gain.
We know the equation for voltage gain.
A-V is equal to output voltage divided by input voltage.
V-O by V-I.
We have studied this, right? V-O by V-I.
Here, we can find the value of output voltage, V-out.
V-out is output current into output resistance.
The output current here is G-M into Vπ.
Then, we can write the output current.
Output current is G-M into Vπ.
Here, we have to put a minus sign because the current is going this way, right?
The current G-M into Vπ is going this way.
We are taking the output from here.
Since the current is going in the opposite direction of the output,
we will put a minus sign in the direction of the current.
Then, minus G-M into Vπ into output resistance.
We have to consider one thing about output resistance.
We will neglect R-O here.
Because R-O will be neglected here.
Because the value of R-O is the output resistance R-O in the common emitter configuration of the transistor.
Since it is a large value, we will neglect R-O here.
If we neglect R-O, the remaining current into R-O will be removed.
Then, what is left? Only this current, right?
Then, current into resistance.
The output resistance here is R-C and R-L.
Both are parallel combinations.
Then, we can write R-C parallel R-L.
So, the equation for output voltage is VO is equal to minus G-M into Vπ into R-C parallel R-L.
Now, input voltage Vi.
What is input voltage Vi?
Input current into input resistance, right?
This voltage is Vi, right?
Then, what is input current?
It is I-B current.
Then, I-B into input current into input voltage Vi is equal to input current.
Input current I-B into input resistance.
Then, the resistance corresponding to Vi is this much, right?
We marked this as R-I'.
Then, we can write I-B into R-I'.
Now, let's go to gain.
Gain is Vout divided by Vi.
Instead of Vout, we can write the value as minus G-M into...
Since I-B is here, instead of Vπ, we can write I-B into R-π.
Since I-B is here, we can replace Vπ with I-B into R-π.
Then, G-M into I-B into R-π into R-C parallel R-L divided by I-B R-I'.
Both I-B and I-B will get cancelled.
We got gain as minus G-M into R-π into R-C parallel R-L divided by R-I'.
This is the equation for gain.
The equation for R-I' is R-π plus R-I into 1 plus beta.
This is the equation for R-I'.
R-I' is R-π plus R-I into 1 plus beta.
Since R-π is a small value in the common emitter configuration, we can neglect R-π.
Since R-π is a small value in the common emitter configuration, we can approximate it like this.
If we neglect R-π, we can write it as beta plus 1 into R-I.
If we approximate it as beta plus 1 into R-I, we can write it as beta R-I.
If you want, you can write it like this.
If you want, you can modify it like this.
If you approximate it like this, the equation will change like this.
What can we give instead of G-M into R-π?
Instead of G-M into R-π, we can give beta.
Beta into R-C parallel R-L divided by R-L.
Minus beta into R-C parallel R-L divided by beta R-I.
After canceling beta and beta, we get minus of R-C parallel R-L divided by R-I.
This is voltage gain without considering source resistance.
We saw how it changes when we consider source resistance.
A-V of S is A-V into R-I divided by R-I plus R-S.
In the case of A-V, we take V-out divided by V-I.
It is the voltage coming from the output of the transistor divided by the input of the transistor.
In the case of A-V of S, it is the output by input of the amplifier.
It is V-out divided by V-S.
Till then, we have to consider both source and source resistance.
If we consider source resistance, we can find V-I is equal to V-S into R-I divided by total resistance R-I plus R-S.
We learned V-I by V-S is equal to R-I by R-I plus R-S.
What can we write from this equation?
A-V of S is V-out by V-S.
We can write V-out by V-S as V-out by V-I into V-I by V-S.
V-out by V-I is equal to A-V into R-I by R-I plus R-S.
We can multiply A-V by R-I by R-I plus R-S.
A-V of S is equal to A-V into R-I divided by R-I plus R-S.
The third thing we have to find is output resistance.
To find output resistance, we short the input side and connect a voltage source called V-X to the output side.
Then we look from the output side and that is how we find output resistance.
We can easily write the value of output resistance here.
I will tell you how it is.
To find the next output resistance, we short the input side.
If there is an input voltage, we short it.
Since there is V-S in the input, we have to short-circuit it.
I have short-circuited V-S.
Next, we replace the load resistor called V-X with a voltage called V-X on the output side.
We replace the load resistor with a voltage source called V-X on the output side.
This is how you find output resistance.
Connect a voltage source on the output side and short the input side.
This is how we do it.
We can call the current flowing through this as I-X.
This is V-X and this is I-X.
We can write the value of output resistance as RO is equal to RC.
RC is parallel.
This effective resistance is the voltage divided by the current.
The voltage coming here is V-X voltage.
Both are parallel combinations.
The voltage and current of the parallel combination will be different.
This voltage is V-X.
The current flowing here is I-X.
This effective resistance is RC parallel V-X divided by I-X.
I call this effective resistance as RE-.
I call this RE- as RE- is equal to RE.
RE is a common resistance for both the output and input side.
RE is parallel.
We have to divide the input resistance by beta plus 1.
When we found the input resistance earlier,
we found that RI- is equal to RI into 1 plus beta.
When we find the output resistance here,
we have to divide the output resistance by 1 plus beta.
It is easier to remember.
Otherwise, we have to divide the output resistance by 1 plus beta.
It is easier to remember.
We are looking from here to there.
Rπ is the series of these two parallel combinations.
We are looking from here to there.
We have to find the output resistance from here to there.
Rπ is the series of these two parallel combinations.
The effect of these two parallel combinations is RS parallel RB.
RS parallel RB is the series combination of Rπ.
So, Rπ plus RS parallel RB.
We have to divide the input resistance by beta plus 1.
We get the value called RE-.
Now, let us look at the output resistance.
The output resistance is RC parallel.
RC parallel is this much.
In this much, we call the effect of this series as RE-.
We call the effect of this series as RE-.
The other resistor is RO.
RC parallel is the effect of RO plus RE-.
This is the equation for output resistance.
This is how we found the output resistance.
We connected a voltage source on the output side.
We connected a voltage source called Vx.
We short-circuited the input side called Vs.
Now, we have to do this.
We took RE- from all the resistors on the input side.
RE is common for both the input and output side.
RE is parallel.
RE is parallel for all the circuits.
In the rest of the circuits, Rπ is the input resistance.
Rπ is the input resistance.
These two are parallel combinations.
Rπ is the series.
We get RS parallel RB.
We have to divide the input resistance by beta plus 1.
We don't have to go into detail.
We just have to remember how we got this equation.
Rπ plus RS parallel RB divided by beta plus 1.
Now, let's look at the output resistance.
RO is the output resistance.
RC parallel is this much.
What else is there in this?
RO plus RE-.
We get RC parallel RO plus RE-.
This is the equation for output resistance.
Next, we have to find out the current gain.
Current gain is denoted by AI.
It is output current divided by input current.
Output current is IO.
Output voltage divided by load resistor.
Input current is IO.
Input voltage divided by input resistance.
Output voltage divided by load resistance is output current.
Input voltage divided by input resistance is input current.
If we substitute this equation,
BO divided by RL divided by whole divided by BI by RI.
We get BO by BI into RI by RL.
BO by BI is the voltage gain AV.
AV into RI by RL.
So, this is the equation for current gain.
In the case of common emitter amplifier with unbypassed,
current gain is AV into RI divided by RL.
So, we have found the input resistance, output resistance, voltage gain and current gain.
If you study the output resistance in this way,
it will be easy for you to remember and write for the university exam.
That's why I explained it in this way so that you can write it faster.
If you want it in detail, you can write it in the comment section.
I will make a detailed video on finding the output resistance.
We can understand one thing from these equations.
In the case of common emitter amplifier with unbypassed,
voltage gain is reduced.
In addition, the input resistance is increased.
The current gain is the same.
In the case of common emitter amplifier with unbypassed,
current gain is the same.
In the next class, we will see the low frequency analysis of common emitter amplifier.
See you.
I hope everyone understood the class.
Thank you.

