Please SUBSCRIBE and hit that THUMBS UP button. It really helps grow our community.
If you want to see the super SHORT version of this video, click this link.
This video is intended to take you step by step through the process of installing shiplap as a backsplash. These same concepts can be used to make any shiplap wall.
Chapters - Use the tick marks at the bottom of the video to skip to each chapter. Intro - 0:00 Pre-painting the Shiplap - 0:46 Installing Boards - 1:55 Cutting Around Outlets - 6:54 Scribing a Board Due to Sagging Counter - 13:12
*My description includes referral codes/links that allow me to earn points or credit that can be redeemed for products and/or subscriptions. When you use my referral code/link, you are helping to support me and my recommendations! Thank you for your support!*
Welcome back guys it's the Tightwad and I have a confession to make. We've been
living in our home for about 10 years now and when we first moved in we talked
about adding a backsplash in the kitchen and as you can see there's still no
backsplash. So we've put a few projects on the back burner for a lot of years
and this is one of the two things that we promised to do when we moved in and
never did. But today that's gonna change. My wife was looking through TikTok the
other day and we saw a video of someone installing shiplap as the backsplash in
their kitchen. So I started down the rabbit hole of learning all about
shiplap and how to install it and today I'm gonna show you how you can do the
same in your home. Here are a couple of sneak peeks at the finished product
which we are extremely happy with. It's time to start painting. I'm gonna be
using the HomeRight finish super max today and I have my boards elevated on
buckets, a sheet of plywood, the cheapest kind you can find. I have a little some
little metal sticks running underneath the boards to elevate them off the
plywood so they're not sitting flush on it and I'm ready to paint. So I have my
Sherwin-Williams emerald urethane trim paint in here and I'm gonna start
painting. Before I start laying paint on the boards I'm gonna spray some lines on
this cardboard I have on the ground just to make sure my pattern looks good. Now
that I'm happy with my spray pattern I'm gonna start spraying. I'm actually gonna
start in the middle and work my way back to me and then I'll do the same from the
other side. If you want to see a shorter version of this video without all of the
tips and tricks and details just click that link in the top right corner now
and it'll take you to the video. I'm gonna let this first coat dry and I'm
gonna come back with a second pass. If there's a need for a follow-up video
I'll link it right here on the screen as well. Once I'm done painting I'll move
these boards into the basement to dry for a few days before I start my
project. The next step I've done is I've created these trim pieces to go on the
end. It has a flat side here where the shiplap will butt up against. It has a
quarter-inch round over here I did with my router table and the thickness of
these trim pieces is the same thickness as my shiplap so it'll line up directly
with the edge here and then come down to the bottom. I do need to use my square
but that's nice and square here so I should have some nice even cuts going to
the other wall on the other side. The shiplap will butt up against it and
create a nice clean line right there. One thing I've done before starting to
measure and cut the shiplap on this wall is to remove this piece of side trim
from my cabinets and I did this so that the shiplap can go all the way from this
side to the cabinets and then we can reinstall this trim piece to cover up
all of the little edge seams right here on the side. To attach my trim I'm using
this rigid brushless battery-powered brad nailer so that I don't have to
bring my air compressor upstairs and I'm shooting 18 gauge 2-inch long brad
nails into the trim and into the shiplap walls. Now I need to go ahead and measure
from my trim piece on the other end to the edge of this trim piece so that I
can cut my first strip of shiplap. I wanted to point out something very
important when you're working with wood that you've bought from a lumber mill or
from a big-box store. This is a called a square so it's going to have a direct 90
degree angle between these two points and if you move it over to the end of
this board you'll notice that this board is not cut square so there's about a
quarter inch on this end whenever I'm flush on the other end here and you need
to always make sure that you use your miter saw to cut a straight edge before
you start measuring for your boards or you're going to end up wasting lumber. I
have my first board cut now. I'm going to slide it in on the far right end. I'm
going to hold my fingers behind it in the middle and bend it a little bit so
it doesn't scratch anything when I'm sliding it into place and I have a nice
snug fit right over here on this seam. You see that it's a nice tight fit here.
Now I don't need adhesive behind this. You can use liquid nails or something
similar behind it but it's not absolutely necessary as long as you're
nailing directly into studs and on most cabinets you'll be able to easily find
the studs because you can see where the cabinet hangers screwed into the studs
up here. So I'm going to make an imaginary line or you could take a piece
of wood and draw your lines where your studs are but I'm just going to look
down here and I'm not going to put a ton of nails in my shiplap because more
nails means more nail holes so I'm only going to have one nail hole showing per
board because I'm going to go right here in the tongue and then I'm going to go
right here in the bottom area of this. Now I don't want to go too low because
we have this same gap down on the bottom so we have about a three-quarter inch
gap so I'm going to go about an inch up from the bottom to put my bottom nail in
and that's going to make it easier on your nailer to go straight in anyway. So
my bottom board was nice and easy. I'm going to start here on the top lining up
that nail head with the screw and then I'm going to come down here about an
inch from the bottom. Notice my nail gun is sitting pretty flush on the counter. I
do want this to go in straight. Lining it up again with my stud. Another thing you
need to consider when nailing next to electrical is you need to know where the
wires are and there's an easy way to do that. The electrical box is always
attached to a stud so it's either going to be on this side or this side of the
electrical box. On this one since I have two electrical boxes side-by-side I know
that my stud probably comes down the middle and also know where the stud is
because of this screw. The second thing to think about is when you wire a house
you're running the electrical wiring down the side of a stud so you need to
make sure you're hitting dead center if you're nailing into the studs next to
electrical outlets. Make sure I don't go too close to the outlet side and then
when you're next to a cased opening like this there's typically a frame all the
way around it so we should have two 2x4s at least width here of stud so I can go
close to the end. Next step I need to do is remove these outlet covers and get my
measurements for my next board. To plan to cut around these pieces I'm going to
first cut the board to the correct length so I'm going to measure to make
sure that my measurement is the same. I can't guarantee that the piece on the
other end trim piece on the other end is square and it's a good thing I measured
we are a sixteenth of an inch longer now so obviously the door casing on the
other side is not square with the counter. With the board cut down to
length I can now mark where I need to have each of my cuts. Fortunately this
light switch is close enough to my trim that the wall plate for the light switch
is going to cover it so I don't need a little thin strip of my shiplap going up
the side here. So I'm going to mark just on the outside of each box and this is
where these extra pieces of shiplap you have come in handy so I can actually
figure out how far down I need to cut. I need these tabs over the edge of the
shiplap but I need this screw exposed so the shiplap needs to run right here
underneath this screw so I'm going to mark this height here. It should be the
same if your electrician did a good job should be the same for all of the boxes
along the wall so that height right there is good for this. I'm going to check
this one down here and that height works here as well. Now what I can do is
take my piece of shiplap and lay it on top of my other piece here and I can
mark that bottom line. I've now come down to the basement and I've marked out
where I need to make my cuts. I'm using a scroll saw to cut all the lines that I
can reach because it's the cleanest cutting saw that I have and it does
details really nicely. I didn't have enough throat distance on the scroll saw
to cut this back line like I did on the others so I'm gonna have to use a jigsaw
to cut this bottom line and to do that I'm gonna take a drill and drill a hole
that's bigger than the blade of the jigsaw and then I'll be able to get my
jigsaw in here and run it down that bottom line. To prevent the paint from
getting scuffed up from my jigsaw because the footplate can be a little
bit abrasive sometimes I'm going to lay down some masking tape where I'm gonna
be pushing the jigsaw across the board. This will serve two purposes actually
it's gonna keep it from tearing out so bad here on the top and it's also going
to prevent the scuffs. With that in place I can easily push my jigsaw blade down
through the opening here and begin my cut. Now I can remove my masking tape.
You'll see I've got a nice clean bottom line there. The next thing I need to do
is remove the screws in these plates. Make sure your power is off before you
start doing this. After you remove your wall plates you'll probably have some
messy sheetrock work behind it which is perfectly fine because it's typically
covered but when we start adding our shiplap that's gonna cause the shiplap
to raise out from the wall. So you have a few options here. You can use one of your
6-in-1 painters tools. I'll put a link to this in the description and in the
pinned comment. You could also use a razor blade knife and then you also have
these types razor blades. These are used a lot when you're scraping windows after
you've painted them. You can just scrape in towards the outlet and don't worry
about messing up the paint around it because you're gonna be covering it up
anyway and then just run your finger along the edges to make sure that you
don't have any loose pieces. With everything cleaned off and our board
sitting nice and flush I'm gonna start in this corner down here then I'm going
to again follow my studs shooting about an inch above. We don't want to hit the
nail from the previous board accidentally. Next step is to get another
board cut to length and then mark our spots and repeat the process and then
we're gonna have a skinnier board for this top section here. I got the next
piece cut and in place so time to nail it in. Cutting this one out is a little
bit different because part of it's going to go beneath the cabinets while the
other half wraps up this wall. So I've already cut the board to length so I can
jam it against the trim piece on the other side and here and I can mark right
here next to this cabinet so I know where the vertical cut is going to be.
And then for the horizontal cut we're going to use our cutoff piece again.
We're gonna put it down just like it's another piece of shiplap, slide it over
and mark it where that top board needs to go. Also need to measure the gap here
and make sure it's the same gap down here to make sure that I can cut a
straight line and that's going to fill our need. You can see how it wraps here
and has a nice tight fit here, nice tight corner there. And I cut this long
line with my table saw and then I cut in the small line here with my scroll saw
again but the table saw allowed me to get a really long straight line. Now you
could achieve this same thing with a circular saw and a brace to run it along
or you could try to freehand it with a jigsaw but you're probably gonna have
less luck getting a straight line with a jigsaw than you would with a circular
saw with a guide or your table saw. I love how this works out. It looks like
we're gonna come right up to the edge of this trim. For this top piece we
obviously don't want this lip on here so I'm gonna go back and rip that off using
my table saw. So I'm not gonna nail this one in yet because I am gonna paint the
top edge of this board before I nail it in so that I don't have to worry about
it when I'm repainting everything. But this wall is finished so now I'm going
around with this wood filler. It's the pink kind so it goes on pink but it
dries to a tannish wood color and I'm using just a putty knife to put that on
with. You can also use caulk or even spackle for this. Here's what I use to
put the brad nails in a little bit deeper if they didn't sink enough. It's
called a nail punch. I'll make sure I'll link this in the Amazon links below in
the description and in the pinned comment. But you just put it on top of a
nail, hit it with your hammer, and it sinks that brad nail a little bit deeper
so that you can putty it in a nice smooth finish. A lot of times when I'm
recording videos and making repairs I learn new things as well and one of the
things I learned is that granite can have a sag. So if you notice right here
in the middle when I put my board down there's about a quarter inch gap in the
center but not down here on the ends. So I contacted a local cabinet maker that
I'm friends with. Check him out. He is holycowleather on Instagram. He
suggested that I first he said see if you can put shims under the cabinet to
lift them up and his second suggestion was to scribe the board and I didn't
know what scribing was so I looked it up. So the concept of scribing is to draw a
line on your workpiece that matches the slope or the curve of the counter. So
what I found was that my mechanical pencil could sit level on the ground and
at the lowest spot of my counter the lead from my pencil touched the bottom
of the board. So I was able to take my pencil and slide it along the counter.
Here I had to do it at a big angle and then here I slid it along and it started
drawing on the board. So what it's doing is it's copying and I'm not gonna draw
on this one because this is not my actual board. It's copying the curve of
the counter onto the board. So then you have a line that you can cut or sand or
plane on to remove material from the more material from the ends of the board
no material from the center and more material here and then it's gonna fit
and I'll show you the finished product. So I swapped out to the board that I
scribed and you can see it sits flush here and stays flush all the way down to
the corners. So I have that bottom board ready and the rest should be good to go.
This is the finished product on the side with our stovetop. You can see the
nice seams there and then how it comes up into the corners. We did not add trim
around the sides here because we got the cuts pretty close and here's a look at
the other side. You can see the finished product with it going up to the top. I
ended up putting a quarter inch round over on the top of this board before
nailing it up there and everything looks nice and clean. If you found this video
helpful give it a thumbs up and subscribe to my channel. If you have any
questions leave them in the comment section below. I always take time to read
each comment and respond if I can. Use the links in the pinned comment or in
the description to buy some of the supplies that you saw me using in this
video. Click any of the videos shown on the screen right now to see other DIY
style videos that I've done and as always I hope you guys have a great day.