Gabriel Popescu is an Associate Professor in Electrical and Computer Engineering, University of Illinois at Urbana-Champaign. He received the B.S. and M.S. in Physics from University of Bucharest, in 1995 and 1996, respectively, obtained his M.S. in Optics in 1999 and the Ph.D. in Optics in 2002 from the School of Optics/ CREOL (now the College of Optics and Photonics), University of Central Florida. Dr. Popescu continued his training with the G. R. Harrison Spectroscopy Laboratory at M.I.T., working as a postdoctoral associate. He joined Illinois in August 2007 where he directs the Quantitative Light Imaging Laboratory (QLI Lab) at the Beckman Institute for Advanced Science and Technology. Prof. Popescu received the 2009 NSF CAREER Award, was the 2012 Innovation Discovery Finalist selected by the Office of Technology Management Office, UIUC, was elected as the 2012-2013 Fellow of the Center for Advanced Studies at UIUC, and a 2014 finalist in the New Venture Competition with Phi Optics, Inc., at UIUC Dr. Popescu is an Associate Editor of Optics Express and Biomedical Optics Express, and Editorial Board Member for Journal of Biomedical Optics. He is OSA Senior Member and SPIE Fellow. Over the past decade, Dr. Popescu has been working mainly on quantitative phase imaging of cells and tissues. He authored a book on this subject, edited another book on NanoBiophotonics, authored 100 journal publications, 120 conference presentations, 24 patents, gave 110 invited talks. Dr. Popescu founded Phi Optics, Inc., a start-up company that commercializes quantitative phase imaging technology.
Get started. So
Good morning. I'm your substitute teacher professor Brian Cunningham. So
you know Gabby asked me to fill in for him while he's away, I suppose and
Yeah, happy to share with you
Another form of microscopy that those of you who are not in my group
I may not have heard about before so I think they're probably appropriate for a microscopy class to
share with you
the form of microscopy that rather than using a
Piece of glass as a surface upon which you're doing your microscopy. In our case. We were using a
nanostructured surface
photonic crystal to
Do different types of biological imaging of cells it was a technique that we call photonic crystal enhanced
Microscopy, so what I hope to do today is to tell you a little bit about what a photonic crystal surface is
What the properties of them are and on how we can use those properties to enable this new form of microscopy
And I'll tell you what photonic crystal enhanced microscopy is
So I'll describe a few applications. We have many applications that we've been developing, but I just picked a couple
representative examples where we're using it for doing label free imaging of
cell surface attachment and then where we can use the photonic crystal to
Enhance fluorescence output to do something that we call a photonic crystal enhanced fluorescence microscopy
In this class we already learned about turf
For example the total internal reflection
Fluorescence no okay, so all right. I was gonna say it's similar to turf, but that now it doesn't matter so
So the the surface that we're using in our work is called a surface photonic crystal
In optical circles some people call the same device a guided mode resonance filter
and so what it's comprised of is a
Low refractive index substrate that could be made out of plastic or glass
We'll see both types of examples here actually I think we'll have glass or plastic ones in lecture today
That has a periodic surface embedded into it
This is a low refractive index material on the top of which we put a high refractive index material such as titanium oxide
In our work we use titanium oxide even though other high refractive index materials will also work such as silicon nitride for example
and so if in most of our work we make up what we call a one-dimensional photonic crystal where this is the
Cross-section view, but if you look at it from the top you would see a series of lines and spaces between the lines
where we have this periodic structure that repeats over and over again, and so
With this a photonic crystal is different from an ordinary diffraction grating
From the standpoint that we design it to act as what we call an optical resonator
Where this structure is designed to interact very strongly with a very specific band of wavelengths
and so by choosing the
The period of the photonic crystal by choosing the refractive index of the
Plastic material and of the titanium oxide material by choosing that the thickness of the titanium oxide
We can engineer the structure to have a nearly perfect reflection at only a narrow band of wavelengths
And so here I am just showing a reflection efficiency as a function of wavelength
We're at this resonant wavelength on the structure acts as a 100% efficient reflector
But at the other wavelengths are the light mostly transmits straight through and so
By choosing the period of the structure we can make this
Resonance happen at almost any wavelength that we want and in our work. We've built them
Anywhere from ultraviolet wavelengths all the way out to mid wavelength infrared
In the work that I'll show you today
We've chosen to make our resonators in the visible part of the spectrum
But here I just chose to show you one in the near infrared around 865 nanometers
So at that resonance wavelength something unusual is happening, right?
and so if we were to look inside the photonic crystal and if we could visualize the
Electromagnetic field strength as a function of time at the resonant wavelength on this is what we would see
so the the light at the resonant wavelength is
Captured by the photonic crystal which tries to turn the light so it can travel sideways
so the the the light looks at this region as a
Net high refractive index region that would ordinarily be a waveguide
So in a waveguide you would have a high refractive index substance
Surrounded by a low refractive index substance and the light will be guided by the high refractive index material
But but here we we don't actually have a waveguide, but instead light that tries to travel sideways is going to encounter
Some you know interference at every half wavelength and get re-reflected back in on itself
So light that tries to travel sideways will get back reflected here
Back reflected there back reflected there
So so light doesn't actually have the ability to propagate very far in the structure like it would in an ordinary waveguide
So what happens instead is all these back reflections?
you cause a
electromagnetic standing wave
where we see the light going from
We see the electric field going from positive to negative and positive to negative over and over again
But confined mostly at the surface and so what you see in this electric field standing wave is that?
Some of the energy is actually in the medium in this case water
That's next to the structure
And so what we've done now is to is to devise a way to take light from an LED or a laser
Confine it to a surface and to amplify its value to amplify its electric field intensity
But that electric field intensity is confined to a couple hundred nanometers from the photonic crystal surface
So if we were to take an average of this over many periods
we could think of this as what's called an evanescent field where the electric field is near the surface, but is
Declining in intensity as you move upwards in a way
And so in this case if we have if we illuminate the structure with an electric field magnitude of 1 volt per meter
What we would see is electric field that's constrained to the surface with electric field value that can be much much higher
And even the hundreds of times higher and so this evanescent electric field is what we hope to use
For interacting with biological stuff on a surface
So in our work we use these photonic crystal surfaces
Routinely for doing biosensing work, and so it's a structure that has
Nanometer scale features, and so it's important to have a way to make them
Inexpensively so we don't have to go to the eb lithography system every time we want to make a sensor
Usually we use them once and then throw them away, so
So we developed an approach called replica molding by which we do we take a glass
Substrate and we put a small amount of liquid ultraviolet curable epoxy on the surface
and then we take a silicon wafer that we've etched an inverse of the pattern that we want to create in our final structure and
we
mush that into the UV curable epoxy and fills in all the grooves on the silicon wafer and
Then we can illuminate with ultraviolet light from the back to cure this liquid epoxy into a solid
And then after that we can remove the silicon wafer away
And so we can do this kind of process using big silicon wafers even up to 8 inch diameter silicon wafers
And we can make these structures very uniformly very reproducibly
Then I'm using your favorite method could be evaporation or sputtering add titanium oxide to the top
And then so the typical dimensions for our visible wavelength photonic crystals is a period of around 400 nanometers
Height of the grating may be 120 nanometers and thickness of titanium oxide 60 nanometers
Then if we want to we can add other things to the top of this titanium oxide
So for compatibility with cells, for example, we may top this off with a few nanometers of silicon oxide
so the upper surface
Appears to cells like glass like it would normally encounter if it was on a petri dish or a glass microscope slide
Yeah, so for the work, I'll show you today. We're making photonic crystals that are around 9 millimeters square
Here's one just on a 1 by 3 inch microscope slide
And so how do we use a structure like this for label-free detection?
And so what I mean by label-free detection is that we're interested in being able to detect
cells or biomolecules
In this case, I'll be mostly talking about cells
Through their intrinsic properties not using dyes or stains
So if we want to detect them by their intrinsic properties, let's think about how we might do that
So if we have our photonic crystal reflection
And so here I've drawn it so that we have a high reflection and the narrow band of wavelengths around 620 nanometers
if we take an object and
Put it on the photonic crystal surface
But let's imagine that this is a dielectric object
What we've done essentially by taking this dielectric object and moving it from here to there
Is that this thing has replaced some of the water and so instead of water being here now?
We have this object that has perhaps higher refractive index than the water it replaced
So when we put something here that has a higher refractive index
We'll get a shift in the resonant wavelength from a lower value to a higher value
Basically what we've done now is to modify the
Coupling condition for light to the photonic crystal. So now a
Higher wavelength now satisfies that resonance condition. And so we call this a change in the peak wavelength value
Now if this dielectric object happens to be an absorber
if it absorbs the resonant wavelength or if it can
Scatter out the resonant wavelength in addition to seeing this wavelength shift. We'll also see a reduction in the resonant intensity
So and what I mean by that is that the reflection efficiency will drop from 100% to some value less than 100%
So we call this a change in the peak intensity value or the PIV
So so going forward in the talk, you'll see a peak wavelength value shift
that's the change in a
dielectric constant when we bring something to the surface or we may see a peak intensity value shift or a PIV shift if our
If our attached object is an absorber or a scatterer of light at the resonant wavelength and so what I
Will focus on today is how we use this photonic crystal for a cell microscopy
And so there's a few different reasons that we might be interested in doing this
So in the world of cell imaging you may have already seen a lot of this in class
You need to have something that gives you contrast
Because cells don't have a lot of native contrast. So so one of the things that a professor Propescu's, you know group specializes in
is using phase contrast microscopy
where
The cells have refractive index that slow down light a little bit and if you engineer an instrument
That can allow you to see cell bodies by their refractive index contrast
That that is very helpful
And in our case we're doing something very similar and for similar reasons to why professor Propescu's group has
phase contrast microscopy
One is that a fluorescent dyes
Have a very limited lifetime
If you if you've done fluorescent microscopy you add your fluorescent dyes to some cells you put them under the fluorescent
microscope and you better act fast because you've got about 30 seconds before the
Fluorescent dyes photo bleach and they go from being observable to being dark again
unfortunately
Cells do very interesting things after 30 seconds that you start looking at them. And so cell processes like
apoptosis a stem cell differentiation
The cancer cell response to drugs some of these things take hours or even days to manifest themselves
And so what people are interested in processes by which you don't have this time limitation posed by
fluorescent markers
Other thing is that you can stain cells with chemical dyes that would make them visible
Under an ordinary bright field microscope
But unfortunately for that these kind of stains are toxic to cells so you can look at dead cells
And so for many things people are very interested in looking at live cells and live cell behavior that can take a very long time
And so here I just kind of show as an example
We are interested in looking at
What happens at the cell membrane and the cell membranes interface to extracellular matrix?
And so I think this is what differentiates what my group does from what Professor Probescu's group does
So whereas his group can look at the entire cell body. We're entirely focused on what happens at the cell membrane interface
So for example cells in the body
Most of them except for the ones that are floating around it in your bloodstream for example are
What are called attached cells?
They are attached to a basement membrane as part of tissues
and so the ways that cells interact with cell membranes is very fundamental to biology and
Understanding many of the processes that cells undergo during all these biological processes
So I'll mention here
Like one of the things that we can do with a photonic crystal
That's kind of interesting if we look at our photonic crystal, and we take a fixed wavelength
So as I showed you first that we can take like all wavelengths
and
Under normal incidence and get this resonance reflection
We can also if you want to choose a fixed wavelength
And then this coupling condition will be satisfied only for specific angles
So so in this way we can take a photonic crystal that has high reflection intensity at specific angles
We can choose to if we want to to illuminate the photonic crystal either on resonance or off resonance
Just by choosing the angle of incidence, so this is a concept that that I'll use later
So if we want to use our photonic crystal for fluorescence
So I just said fluorescence is bad
But it's not like a religious belief people still use fluorescence and plenty in plenty of self-related work and so
We can use our photonic crystal for fluorescence
By illuminating on resonance where we have this big electric field on the surface
So here just to show you the difference between on resonance and off resonance illumination
this plot shows a
Electric field magnitude as a function of position in one period of the photonic crystal
Where here's our water on the surface or titanium oxide and silicon oxide?
Where you check out the you know the magnitude of the electric field
So so on resonance the electric field is can be in the hundreds of volts per meter when we illuminate with one volt per meter
Whereas off resonance the electric field magnitude is close to one volt per meter that we illuminated with
So we can switch
between on and off to expose any fluorescent material here to either high field or low field and either turn its
Brightness on or off
Another interesting feature is that the electric field magnitude drops off as you move away
From the photonic crystal in a very predictable fashion. It has an exponential fall-off like this and so I'll show you how
We can use this on-off feature and our knowledge of the electric field magnitude drop-off
to help us
estimate the position of fluorescence emitters
Above the surface and so in ordinary fluorescence microscopy you just look at fluorescence intensity
Our method of being able to tune on and off and to use this known electric field profile
Allows us to actually estimate the position of fluorescent dyes
Relative to the photonic crystal surface
So so let's go back to a label-free detection again
Where I mentioned we can take a nano object or a big object put it on the surface
We have these changes in peak wavelength value or peak intensity value that we can measure
So so how do we?
integrate this
sensor with
Microscopy so here's in our laboratory the photonic crystal microscope
So it looks kind of like a regular microscope from the standpoint that we have
ordinary microscope body
But instead we have a spectrometer on the side over here
I'll show you how we use that we have our illumination is you can't really see it. It's kind of through the back of the system
But schematically it is it looks kind of simple so so we take a light emitting diode
We filter out one polarization
Because we only want to illuminate our photonic crystal with a light that's polarized along the grading direction
And that's that's the direction that gives us that that resonance
We reflect that light and we put that light through a cylindrical lens
So the light is focused down to a line and we put that line through a microscope objective that illuminates the photonic crystal from below
The photonic crystal has that resonant reflection the reflection comes back goes through that same microscope objective
but we put it through a dichroic mirror into a into a
imaging spectrometer that allows us to measure the
The peak wavelength value and the peak intensity value on every position on a photonic crystal surface, so how do we do that?
So so let's imagine this things our photonic crystal surface the grading lines going that way
And that these little smiley faces represent some cells that are on the photonic crystal surface
So I mentioned that we take our light emitting diode and we focus it down to a line
So here's our line of illumination on one position of the photonic crystal surface
so if we take
One pixel out of that line that pixel is represented by a reflection spectrum like I've shown here
By reflecting the light into an imaging spectrometer at one in one snapshot
Actually, we gather a spectrum for every position all the way across this line
In our system, we have a spectrum for every half micron increment in space going in this direction
and so in in one snapshot from our
CCD camera we measure
512
spectra
Each spectra representing one place along the line makes sense so far
okay, so so now imagine we take this line and we
Actually, what we do is move the photonic crystal underneath the line in small increments
So that step-by-step we rebuild a big data cube where each position in the y-direction
Has 512 spectra associated with it
and so we have the ability now to go into all this data and
Pick out the peak wavelength value and the peak intensity value for all
512 by 512 spectra
And so what I show here is it looks like an image
But it's not like really an image like you would ordinarily get from a camera
Each pixel in this image is represented by one of these spectra where each of spectra has a peak associated with it
Within which we can analyze the peak and find for example
the wavelength of maximum reflection and so this image
here for some pancreatic cancer cells
Ordinarily this would what they would look like in a bright field microscope image and a photonic crystal microscope image this image represents
the
Contrast bar represents wavelengths of the maximum reflection
So for example in a place where there is no cell I call it the background would have a lower
Wavelength place where there is a cell we'll have a higher reflected wavelength
And so if we zoom into this example image, you can see some interesting things
And so for example, we can very easily observe
The cell attachment footprint as we call it and how different cells have even
Supposedly identical cells here growing on a photonic crystal surface have very different
Footprints that even within an individual cell can have regions of low attachment
Strength regions of higher attachment strength and an interesting shapes in terms of how the cells attaching to the surface and starting to spread out
questions about that
Okay. So so what we found is that
Cells have very interesting and distinct cell attachment behavior that we can observe with the system
And so here I'm just showing a few different types of cells and their attachment footprint
as measured by the photonic crystal microscope with the color bar representing the wavelength of maximum resonance and
so here's an example of
one of the things we can do looking at
stem cells
Differentiating over an extended time period in this case over 10 days. And so our
instrument is
Integrated with a cell incubator so we can keep the cells in the instrument and alive
For many hours or many days and we can take snapshots of their cell attachment for many different times
And so for example, we see that cells initially attached to a blank photonic crystal by small
Attachment points on those attachment points spread over time
Cells do some kind of wild stuff. And so for example, here's a cell that has a strong attachment in the center
Followed by like a corona where there's no attachment followed by heavier attachment around the outside
Here you can see that the same cell ten days later has like a center area a little gap and then more
Cell attachment around the outside
So interesting things that are going on in there in terms of how do the cells attach and how within even within an individual cell
How the cell attachment varies from place to place?
So since we can take a one image
We can take many images. And so for example here at ten minute increments
Here's a stem cells attaching versus blank that initial attachment point the initial attachment point as spreads
An interesting thing you can see here is that there's a cell here
You can see that the cell is there in the bright field microscope image
But it hasn't attached and so what we see is that as a cell forms the close association
with the photonic crystal surface
It actually starts to register these changes in wavelength
You can also have cells that kind of hover around and sit near the surface
But don't actually attach that they're like physically present, but they haven't attached and so we can actually even see how this one attached
Spreads gets joined by its brothers and sisters later
We can do things like make
Dynamic movies of the cell attachment like outline how that changes with time and we can even dive into these images
One pixel at a time to see how even one pixel here if you look at the red one on the red one is
So here like the black line is for the cell that's shifted for where a cell is attached
The green is for like the background area
He did this cell is gonna spread over the red pixel
And you'll kind of see that the red pixel shifts from being over on the left to being over on the right
Once the cell kind of goes over that point, so we believe pretty strongly I think we've
Established that these peak wavelength value shifts are
Indefinitely associated with the cell membrane and the cell attachment over these these these places on the photonic crystal surface
And so with that kind of thing we can make a photonic crystal attachment movies where this shows one of those cells
Attaching and then spreading as a function of time
And we can even make
You know like movies of the cell boundary and how it evolves with time
Here's kind of an interesting experiment where we have some stem cells
Attaching to a photonic crystal here. We were taking images every two minutes
And so you can kind of see them attaching you can see the peak wavelength value being
Relatively higher in some places other than rather than others
What we're gonna do is after these cells attach we're gonna kind of skip ahead in time
So now we have lots of cells attached
We're gonna expose these cells to a drug called trypsin that kind of shocks the cells and god they jump off the surface
So you kind of saw them like I'll go off the surface
Then they kind of start to reattach find their way back to the surface
And so we can clearly see that these images that we are
There that we're gathering
Represent an actual cell attachment in the cell attachment footprint. I think we have one more trips in exposure
They'll kind of do their jumping thing again in just a minute. Yeah there they go again
So we've done like other kind of little cell tricks
This is one where we did a chemotaxis experiment where we put
Up here out of the field of view an agarose bead that has a chemical attractant to this attached cell
if I can figure out how to
No
Maybe I won't do that. I need to find my pointer
Rats oh there it is
Okay, so so this cell is going to you know gradually kind of move from
South to north as it senses
Something it is environment and is going to actually like a crawl itself
in one direction
So
One thing that we found is that we really use this as an imaging modality using the wavelength shifts initially and so we
You know our hypothesis was basically that either the cell membrane and its components when they attach to the photonic crystal
those cell membrane components are engaging with that evanescent field and
Displacing water that would ordinarily be there with your high refractive index stuff
That's like the lipids in the cell membrane the proteins that are you know behind the cell membrane
And that that's what we could observe with photonic crystal microscope. Yes
So
so what we're observing is just a change in the
Coupling condition for the for matching the resonance between the incoming light and the photonic crystal
That that's right yeah, yeah, so so we're not really you're not really changing the light itself
We're illuminating with a broadband of wavelengths from an LED and only in the photonic crystal only reflects back a narrow set of them
So that's actually one of the good things about this system is that we can illuminate with
with low intensity light
from a broadband source
We're not really imparting much energy to the cells themselves
So it's like the people get concerned about like photo toxicity and using lasers to illuminate cells right here
We're using very low intensity light
So yeah excellent question though any other does it make sense
Okay
So in our work we were using that though the wavelength shift primarily
But we were gathering all these spectra anyway, and so we kind of asked ourselves
What would we see if we also looked at the peak intensity value?
So I'd like to act like we were a genius and we thought there was there was all this information in the peak intensity value
Things that we were measuring, but in fact we kind of discovered it by accident later, and so here
It was looking at some I
Think these are dental stem cells attaching with the peak wavelength value mode
First of the blank surface and then to kind of you see them attaching and spreading over time
We can look at those exact same cells rather than looking at the reflected wavelength
We can measure the reflected intensity and what we see is something very different
And so if we zoom into some of those cells
What we see is that the places where there's the most wavelength shift
Are not the same as the places where there's the most intensity shift and so here
These are like arbitrary units, but but red represents places where there's more reduction in the reflected intensity
And so you can see that these are kind of localized in some cases around the perimeter of the cell
But not always here's one that has a big shift in the center of the cell
But then it changes so it's around the perimeter
So we started thinking about well, what's going on? Well? What are we seeing that's different in a peak intensity value shift?
You know here again did a zooming into to one cell and here I wanted to show you this so you get an idea
Of the resolution even within an individual cell on that we can study on the cell attachment footprint
So I think these images have pixels that are 0.5 microns on a side
so our
So here so we can do the same thing with movies. We can take peak wavelength value movies
I can move ahead. I think we have to watch the whole movie
Sorry about that, and then or we can make a peak intensity value movie of the exact same cells and so our thought here is that
Cells as it turns out and there are not like big water balloons that have uniform
Your characteristics all around their outside cell membrane
When when cells attached to a surface on the way they do it is by something called focal adhesion points
And so these focal adhesions are represented by places on the cell membrane
Where proteins gather up together in aggregates not only in the cell membrane themselves?
But they're backed up behind the cell membrane by things like actin filaments and other
aggregated proteins that
Make like a link between the inside of the cell and the outside of the cell and in fact that this these focal adhesion points
are how cells communicate with their environment and
transduce information from the outside of the cell to the inside of the cell and
so our hypothesis and one of the things our research group is working on actively now is is to show that these
Cluster areas represented by
Reduction in the peak intensity are
Due to aggregates of protein that are scattering out light more efficiently in those places
Compared to other places and that in the places where we see a peak intensity value change is a place where there's a focal adhesion
One of the things I get asked almost any place I give a talk on photonic crystal microscopy
Is what's the effect of that grading structure the photonic crystal nanostructure on the cells?
And so I got so tired of answering that same question that our group
Actually developed a way to make the photonic crystal surfaces planar
So that we wouldn't have the following problem
so so one thing that we would observe very consistently is that the the photonic crystal grading direction if it goes in a
Particular direction we don't actually see the grading the grading is too small compared to the cells to actually show up in our images
but the cells know it's there and the cells have a way of
Sometimes sensing that environment and growing their attachment along the the grading direction, and so we've developed a way to
Fill in the grading grooves with a polymer called SU-8
We developed a horizontal dipping method that would allow us to place
Just a very small
Thickness of the SU-8 within the grading grooves, and then we etch it back slightly
So it just barely fills in under the surface
But when we do that we can here just showing an atomic force microscope image have it go from like grading mode
To planar mode here to just showing that our grading structure would ordinarily be about 100 nanometers
I'm after we planarize it. It's down to less than a nanometer in
thickness variation
And so if I can manage it
The the ones the cells in the left are growing on a regular photonic crystal and
Eventually you'll kind of see them form attachments
With the cell grading direction going up and down
Whereas on the
Planarized one we see a behavior. That's more
evenly balanced they don't seem to sense the grading direction anymore, and we will see them spread out in the left and right directions and
Up and down directions and about about equally
Okay, so I think this in the last few minutes. I wanted to share with you one more thing
About fluorescence and fluorescence enhancement using cells in this photonic crystal microscope, so I alluded to it a little bit earlier
So a label-free direction detection is a fantastic
Fluorescence is still heavily used in cell imaging and we have this ability with the photonic crystal to
Amplify the electric field and to boost fluorescence output, so we thought why not see what we could do
With fluorescence enhancement using photonic crystals and using this same microscope
And so we have this ability to tune between the on-resonance and off-resonance condition
By choosing the incident angle if we use a fixed wavelength so here. They're just choosing a
Monochromatic light source such as a laser to illuminate now
There's specific angles that that wavelength will couple into the photonic crystal
So it kind of repeats what I said before so so what we did was to incorporate a second illumination path
into our instrument
So this is the the illumination path that I told you about before for doing label-free imaging
What we added was this where instead of an LED we have a laser on the laser goes through an optical fiber
That expands gets collimated by a collimating lens
And then we put that we have the ability to choose between either label-free imaging or fluorescence imaging
I'm using this mirror
We can put the light through the same cylindrical lens focus it down to a line and then illuminate our cells from below
on the photonic crystal now now one thing that
Very important is actually here with these up sneaky arrows, so so as we have the ability by
This the cylindrical lens
Its focal point is on the back focal plane of that objective, so I'm not sure if you learn this in microscopy class
but if we
Change the the position of this focus point to be
Off
the focal plane of the objective
We can manipulate the angle of incidence of light that emerges from this objective
and so what we have in our system is a way to
Move this cylindrical lens on the cylindrical lens sits on a computer-controlled motion stage
So we can translate it and by translating it
We translate the position of the focus point and by translating the position of the focus point
We can manipulate the angle of incidence on the photonic crystal that kind of makes sense
Yes, yeah, yeah, so it was the same same basic thing
I think I think you may have got the idea by talking with professor Popescu about this so
So so with the system now we have the ability to
quickly switch between on resonance illumination and off resonance illumination
Using using that that laser source
and so
so here is
fluorescence images
They're also taken by line scanning so we do so but rather than gather spectrum. We just gather
Fluorescence intensity as a function of position. We don't have to measure
Peak and wavelength values or peak intensity values. We just measure fluorescence intensity for the light
Going this way and so we don't use our spectrometer as a spectrometer anymore. We did we just measure the fluorescence intensity
So
So here's some fluorescence images of mouse fibroblast cells
Attaching to a fiber necked encoded photonic crystal where we used a stain called a cell mask
That's supposed to only preferentially stain and cell membranes
And so if we take a off resonance image of these cells
You know, we can see the places where there's more fluorescence intensity
If we if we then change the illumination angle
We can get an on resonance image of the same exact cells
So you're not much really changed here except you notice that they went from lower intensity to higher intensity that that's our different. That's our
photonic crystal enhancement happening
So so we can do something with these two images the on resonance and off resonance image
We can take a one and divide them by the other on a pixel by pixel basis to make what we call an enhancement factor
Image so an enhancement factor image is basically I guess what it is
It is an image of what the enhancement factor is for each of these places in the image
So so what do you see in an enhancement factor image? That's different than what you see in a regular fluorescence fluorescence image
well a fluorescence image
Tells you something about the amount of fluorophore that's within each pixel in the image
That the more fluorophore stuff that you have gathered in one place means more intensity, right?
Now if we do if we take an enhancement factor image
what we've done now is to normalize out the amount of fluorophore and what we've done instead is to
weight the
The intensity of this image by how close the fluorophore is to the photonic crystal surface
so since we know the
the like mathematical equation that describes the
The
Drop-off and enhancement factor as you move away from the photonic crystal
we can take this enhancement factor image and make an estimate of the
Position of the fluorophores from the surface in units of nanometers
So so with somewhere on the order of nanometer resolution
We we can we can say with an enhancement factor image how close a fluorescence emitter is from from the surface
So we did this with a membrane based stain. We did the same thing with a nucleus stain
So so here's a stain called nuke red
it's supposed to
You know stick to nuclear components only stain the nucleus and so what we were wondering what we would see in an image like this
Because obviously the nucleus is not in the cell membrane. It's behind the cell membrane and so
But still we could see like an off-resonance image and on-resonance image
So it's an image of the same cells just higher intensity here make an enhancement factor image and then actually you'll see
Within the cell how close the nucleus is to the cell membrane underneath it
so
so to conclude
We're using these nanostructured photonic crystal surfaces
To do some unique things that aren't available in other forms of microscopy
And so one of them is the label-free imaging where we have this ability to take
Images of the peak wavelength value or the peak intensity value
It's a label-free approach
that is focused specifically on what happens at the interface between the cell membrane and the surface is attached to and this is a
Biological situation is very common for many types of cells that people are interested in
People are also interested in
Knowing where things are within cells and their distance from the surface and so if you can label something with a fluorescent dye
You can use this enhancement factor image modality to help locate
Things at least in the z-direction with very nice resolution
So of course the students in my group. I need me to thank them profusely
I'm glad there's four of them here today
Now none of you all are doing fluorescence microscopy kind of work, but
You never know
So so obviously the students in the group did all the great work that I showed you here today
Of course we have funding from National Science Foundation and NIH to help us along so oops
So we're happy to answer questions really appreciate your attention today
Thanks for clapping. You don't have to clap in class
Line scanning
It might it has a time resolution
So the CCD, maybe I didn't explain clearly enough, but the CCD actually is is functioning as a spectrometer, so
Yes, so so it's it's a I guess what you would call a imaging spectrometer
Sorry, so yeah, it's an important point, so I'll try to
Explain when you get to the instrument here. Yeah
so
what I didn't explain very well is that the the spectrometer has a
slit that the the line of light enters behind the slit is a diffraction grating and so the
Diffraction grating spreads out the the light among its if long it's a spectral components
So in one dimension of the CCD image is spatial
So like so like that the spatial dimension of the
CCD image represents like a place
the the other dimension of the
CCD image represents wavelength does that make sense?
so it's because we have a diffraction grating is taking the line of light and
dispersing it we're able to measure the
the
Resonance reflection as a function of for each of these pixels. Does that make sense?
Yes, yeah, that's right. I mean our spectrometer actually goes further than that. We only care about a narrow part of it
Yeah, so yeah, we throw away most of the data from our spectrometer and only focus on this narrow part
Make sense
Refractive index structure of your sample and also how well the attachment that's right. Yes
Yep
Yeah, I think we look at both at the same time so it's hard to separate one from the other and
If it's possible at all
so
So so as a cell attaches to the photonic crystal like you say it
Attaches but then a cell has all this stuff behind the cell membrane the cell membrane itself is maybe only
like five to seven nanometers deep, but our
Evanescent field is maybe 200 nanometers deep. So what we're really looking at is a cell membrane and whatever is behind the cell membrane
so
We kind of estimate more or less that like all the protein components inside a cell have
Around the same refractive index and the research kind of supports that
that that if you kind of think of the
like the the cell is like a bag full of proteins and lipids and and
Stuff that most of that biological material has very similar refractive index to each other
But as it gets closer to the surface its effect on the reflected wavelength is more
So we are kind of measuring a combination of how close it is and how much stuff there is
at the same time
And I think that it's one of the things that's interesting about the peak intensity value
modality is that
when there's
protein aggregates
That that scatter more than their their surrounding area that that perhaps we're able to see that
But but that doesn't show up as a different refractive index it shows up as scattering
So why is that? That's what I call it. That's one of the things that we're currently working on
Yeah, the having better quality factor will give more enhancement
It doesn't necessarily make the amount of
Shifting more
So we can manipulate the the quality factor a little bit by choosing the refractive index of the material or the
Thickness of the grating or depth of the grating take things like that. We kind of have a trade-off. We want the
The resonance to be relatively easy to measure at the same time
so if it becomes really narrow, you may only get a couple pixels worth of
Of
Reflection spectra out of your spectrometer, but we'd really like to be able to to measure like the whole curve
Yeah, so we kind of have a trade-off between
Like resolution and then ease of coupling light into it
Oh
To tune to make what part
Well, we use so to we make a
master mold out of silicon
where we'll have that made at a
silicon foundry
By DPV lithography, I'm usually using a stepper here to make like a big
Grating master. It's also possible to go into our clean room and have a master made by evening lithography
There's even companies you can go to to buy gratings with different dimensions
so we use the grating as a mold that we embossed into
A UV curable polymer using that replica molding method that I mentioned. Does that make sense? Yeah
Great questions. Okay. Well, thanks so much. Hope you have a good rest of your week