Building The Mountain Bow (Part 1)

Kramer Ammons
208 followers
Thank you for watching!
The archery company I am Building
👉 https://www.shatterproofarchery.com/
ARCHERY PRODUCTS I RECOMMEND
🏹 https://geni.us/AMZLinks
Affiliate links were used in this description
“As an Amazon Associate, I earn from qualifying purchases.
”Thank you for your support
#kramerammons
#bowmaking
#traditionalarchery
I am not supposed to be making this video, but inspiration comes and it goes like the
wind.
So I must raise my sails and allow the wind to take me.
So where am I going?
I don't know.
All I do know is that the wind is on my back.
I spent more money than an entire month's of YouTube income on archery targets.
And I'm supposed to be making those videos in hopes to recoup some of those costs so
I could keep making videos.
For today, the targets will collect dust.
And that is the first of two reasons why I should not be making this video.
The second will likely cost me ten times more than the first.
But I'm doing it anyways.
Building this bow has been on my mind for a long time.
The idea is to have the most portable hunting bow possible.
I like to run the mountains and push my body.
And I want to make the best packable, portable, small, fast shooting hunting bow that I can
pack in my backpack and run safely.
Is this a practical bow for most people?
No, of course not.
You kind of got to be a little crazy to do some of the things I do.
But again, I'm not supposed to be making this video.
The spirit is leading.
The spirit is like the wind.
I can't see it.
But I can feel it.
And it's stronger than nearly anything.
A skill is learned from practice.
Today I am doing things I have not practiced.
But I have done similar tasks.
Today will be a learning experience.
Hopefully I can gain new skills.
The right way to do something is not the best way to do something.
The right way to do something is doing that thing the best you can.
I can't make it perfect.
If I could, I would stop.
But the imperfections make way for improvement.
And the idea of improvement is hope.
Using this type of form is a new way to prototype bows for Shatterproof.
The idea is to make something that's not perfect, but that works well enough to know if the
bow design is something we would like to move forward with.
The riser is built from scrap wood.
In this case, Osage scrap wood.
It's great because it's so dense and durable.
Our two shops are close to each other, but we do not have a door entering to each other.
So I have to go through the garage door to access the manufacturing area.
I work early in the mornings, late at nights, and on the weekends, so I don't interfere
with our employees' work.
Maybe one day I'll be able to have duplicates of every tool I need so that in my own shop
I can prototype from start to finish.
That would be awesome.
The form on the first limb didn't hold up great for me, so on the second one I added
this piece of plywood with screws just to keep it straight.
The problem was that these straps stretched out more than I wanted them to, so the hose
started to become really round on where it contacted the bow.
Otherwise, the straps were a great solution that Zach came up with for quick prototyping,
and I think it'll work more in the future, especially after using the same straps.
They'll probably stretch less and less.
bows to sell, the main two are how the bow performs and how the bow looks.
As far as selling things online, how the bow looks matters a lot, but I will never sacrifice
how the bow performs for how it looks.
I would rather have a bow that doesn't look perfect, but performs great, because from
that point we can change the looks without changing the performance.
But to do it the other way around is a headache and will take more time in the end.
The first one is not supposed to be the final one.
On the bones, I built at least 50 bows before finally settling on a design.
And even after that, we've tweaked it and improved it based on customer feedback.
But with the basics figured out, I think I could build less than 10 of these to get the
design I'm looking for just right.
And that's my excuse for making this bow, because I'm not supposed to be making this
bow.
But to use the justification that it will be for business and I can sell a version of
this someday has given me the peace of mind to spend a few days building the bow and a
few more editing this.
The second reason that this bow could cost me 10 months of YouTube income is probably
not what you think.
I've messed up on this part of the bow three or four times because I just tried to transfer
my lines rather than build a jig.
And the bit will walk a little bit, so it was not consistent, and I had to refill these
holes for the pins with dowels and try it again and again and again.
Building a jig is kind of like building a habit, and once it's in place, you can just
use it freely and forget about it.
I should have done that.
A bandsaw blade that can't make the sharp curves of the cut will ensure that the wood
burns.
This is the first ever three-piece takedown bow I've made out of countless hours of making
bows.
I've never done this.
This will allow for clarity on what needs improvement.
I deviated from my original plan, which has caused me this moment.
I created long fade-outs, 8 inches.
The fade-outs were too thick, so about a third down the limb away from the handle, a hinge
is starting to happen.
And I know if I continue with this, it could be disastrous, so I'm pondering my options.
Off camera, I reduced the limbs by 2 inches each, cutting off the 2 inches that attach
to the riser, causing me to re-drill the holes for the 4th time, which was painful.
But you can see the immediate difference here on this bow, and how it's starting to bend
off the handle much better.
The problem is, now the bow is 4 inches shorter than originally planned.
Podcast.
I have a podcast?
Yeah, so our podcast is live.
It's official?
I struggle knowing when to quit on a bow, especially after putting 3 or 4 hours of footage
into a bow, and wanting to make a video about it.
But if I reach a point and I know it's not the bow I want it to make, it's tempting to
toss it to the side.
But it's much more difficult to toss it to the side when the bow takes 4 times longer
to make because I'm filming it, than if I were doing it off camera.
I'm more emotionally invested in a bow like this.
Did I hear anything that time?
Kind of, it's cool.
Yeah.
In the mechanics of bow making, something we have to avoid is stacking.
Stacking happens when the string and bow angle gets beyond 90 degrees, and that's what Kaz
is testing here.
We're going to mark that point to figure out our max draw length.
The limb shape, the riser shape, and the limb length all play into stacking.
And because I made a 52 inch bow with straight limbs, we're stacking very early.
I can't get more than that.
I mean, you did make it pretty short.
On the other hand, this bow is a very smooth shooting bow, which is kind of cool.
I have a 29 inch draw length, and so 25 inches looks kind of odd on me.
But I marked the arrow so I knew where to stop drawing back.
That's 24 inches.
The second reason for not making this video is the exact same reason I made this video.
Because I don't make my own videos for money.
I'll make other people's videos for money.
My videos are made because the wind blows.
Thank you so much for watching today's video.
If you're new here, my name is Kramer Ammons.
It's a pleasure to meet you.
I make bows.
I like archery stuff.
And I also started a company by the name of Shatterproof Archery.
And we manufacture archery goods, meaning leather goods, bow strings, bows, right here
in the USA.
Actually, 20 yards away from me, guys are making stuff right now.
So if you're interested in supporting a U.S. company who makes high quality archery gear,
check out ShatterproofArchery.com.
The support has been fantastic.
So many new people are joining the YouTube channel and finding Shatterproof Archery.
It means the world to me.
And as always, stay shatterproof.
I'm for you guys.
And I'll see you on the next video.
And on the next video, I'm going to make a bow that I can pull back to full draw length.
