We’ll show you one of 5 ways to wind up extension cords. The Cord Bucket method is an effective way to wind and stow cords - buckets are readily available and there are several option you can do to customize your cord bucket!
This is one in a series of episodes showing different methods of winding up and/or using extension cords. In this series, we will show the daisy chain, over-and-under, figure 8, cord reel, and cord bucket approaches.
This episode features the “Cord Bucket” method. These are simple to make and easy to customize to your preferences.
No matter what method you use to wind up your cord, always get the BEST extension cord you can afford. The cheaper the cord, the stiffer it will be, especially in cold weather.
Extension cords come packaged in a coil (much like a garden hose) or looped into an oblong shape with a sleeve around the middle. For the jobsite, we recommend 14 gauge or higher. Remember, when it comes to wire gauge sizes, the smaller the number, the larger the conductors.
For that new cord, unwind and stretch it out somewhere in the sun. It can be on the lawn, sidewalk, or driveway. Leave it out for about an hour to get the cord warm so it can “relax” and lose any memory it acquired during the time it was packaged. If it’s winter when you get your cord, place the cord somewhere warm until the cord is supple. Now you wind up the cord using the method you prefer.
The basic layout of a cord bucket is a hole low on the side of the bucket that allows the male plug end to come from inside the bucket and extend long enough to plug into a wall outlet. After the hole is drilled (1-½”/38mm is typically large enough), the end is passed from the inside to the outside of the bucket to the desired length. Then, the remainder of the cord is coiled inside the bucket until the receptacle/female end is placed on the top of the coil The lid is then placed on the top to protect it from weather and such.
There are several variations and enhancements to the basic bucket. Here are a few of them:
Drill small holes in the bottom of the bucket in case water get in so it will drain out. Add cleats to the bottom to reinforce the bucket bottom a bit and raise it of the floor. Inset an outlet in the lid of the bucket Use an approved weather-tight box and cable mount on the end of the cable to have more outlets to plug into. Remember, the combined draw on all the outlets can not exceed the cord rating. Cut side-slots on the edge of the lid to make the lid easier to place and remove, but still be secure.
There is an active debate about the safety of using coiled electrical conductors. Is it safe?
The answer is a conditional “yes.” Remember, mounted cord reels are used in industrial, garage and shop settings routinely and many of these reels are government safety-agency approved. Coiled conductors in a reel are deemed safe when the total combined electrical draw on the device is lower than the rating. As a safety measure coiled cordage is always rated lower than the usual rating for the same conductor when it is uncoiled. This is because coiling conductors does introduce some resistance and resulting heat.
This is addressed by rating the cordage lower with the idea being that less current will be utilized with that particular setup.
Some tradespeople also have the practice of pulling all the cord out of the bucket because then there is no risk of resistance/heat due to coiling. Indeed.
My practice has always been to avoid coming anywhere near the capacity of the cord when running power to the jobsite. This is asking for trouble, whether the extension cord is coiled or not.
The same is true of the capacity of the circuit that you are plugging your extension cord into. If you exceed the rating, you will heat up circuits and (hopefully) trip breakers before damage is done to the electrical components.
While you’re at it, check out these OTHER methods that trade professionals use as well:
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. This is one in a series of five videos where we
show you great methods that trade professionals use to stow the cords. In this case, we're going
to show you how to do a cord bucket. Very inexpensive, effective, and we'll show you the
good, the bad, and the ugly. Stick around. To build a cord bucket is a really simple affair. All you
need is a five-gallon or seven-gallon utility bucket. Obviously, you can get these from all
the home improvement stores, paint stores, all sorts of, even feed stores. But a bucket like
this, something with coloration, tends to last a bit longer out in the sun, I've found. So you can
utilize a bucket like this. The next thing you need is a hole saw set. I really like this little
set from Milwaukee, but this needs to be big enough that when I cut a hole in the side of the bucket
down here, that the cord end, the male end of the cord, will come through that hole. And you'll see
that'll work just fine. Of course, a drill motor to do drive and to cut these. And then you just
need a set of drill bits. We're going to use probably three-sixteenths or eighth inch to drill
a series of holes at the bottom of the bucket so that if this bucket is open and you get some
rainwater in it or it gets condensation in it, it'll tend to weep out instead of creating a swamp
inside of this bucket. All right. And of course, when you get the bucket, you want a lid with it.
Now, in my case, with this lid, if you look close, I actually took this on the bandsaw or jigsaw, coping
saw or whatever you've got, and I cut a little set of notches approximately every two inches around
simply to make it easy to pull this open to pop it on and off so it isn't a hassle factor.
You don't need that at the end of the day or at the beginning of the day when you're trying to get
going where you can't get the lid off. So that's going to serve us well. Okay, let's go ahead and
get this constructed. Okay, choose a spot on the bucket, and I always go up about, oh, that far, a
couple centimeters or about an inch up, and then drill on the side of the bucket right here. This
is where the male end of the cord is going to come out. First step done. Now let's go ahead and drill
some holes in the bottom. So I drill around six holes around here. So we'll just do this.
Now your bucket is ready to take the cord. Now go ahead and take the male end of the cord, feed it
down in the bucket, out the side of the hole there, pull a little bit of a pigtail out the side long
enough to where it can be plugged in, but we'll stow that better in just a moment. So this could
be plugged into an outlet or job site extension cord, main power tap, and now you're simply going
to coil the cord in. All right, this length's about right for plugging in, but it doesn't transport
real well. This is in the way. This is a risk of getting damaged. It gets caught on things.
So what I do is shorten the cord, and to do that, look down inside of this bucket here, and you'll
see what I do is I push this back in, and when I do, you can see which item it is.
Just pull it and get it shortened up, but I don't put it back in because you don't want to go hunting
for it. About like that. Now this is ready to transport once you put the lid on. All right, now
you've pulled out this. You're ready to plug in. You're ready to use your cord. You can take off
the lid here, reach in and get your tap in, splay it out, and you're ready to go to work. Now there's
several modifications, and you probably have some of your own favorite, and if you wish to share
those with your fellow viewer family members, do so in the comments below, but here are some of the
modifications I've seen to this lid or different kind of lids you can get. For instance, some lids
have a half hinge on it, and you can get those sometimes from feed stores, those types of places
where the lid goes down but half of it hinges up, allowing you to pull the cord out, keep the lid on
it, and then when you're done at the end of the day, you feed it back through, flip the lid on the
other half, and everything's back in, and then you just feed this in, and that's done. A second one
is to put another hole or a notch right on the edge here that is just big enough for the cable
to come out of the side, so you can keep the lid with it at all times, and this lid doesn't get lost.
That's another modification that's really inexpensive to do, and keeps it relatively
dry inside. A third one that I've seen that is pretty cool is to actually make this lid
an outlet end. Now that means that if you have some cordage but you don't like the end, and we
really do like these triple tap ends, illuminated ends from watts wire, but if you have one that's
not nearly as useful, you can cut the end off of this, and with using Romex connectors and such,
you could put a four or a couple duplex 20 amp outlets on here. They're heavy duty and work well
for construction, and now you have an outlet here. A couple caveats, okay. Number one, it's never a
good idea to use heavily loaded coiled wire, and when I say heavily loaded, where you're drawing
a lot of amperage through it. So let's say, for instance, you have on the job site a moderate
size compressor, you're running a table saw, you have also other tools that are intermediate like
miter saw and all that. Well, all those running together at the same time can exceed the deliverable
capacity of the cordage, and because it's coiled like this, you're going to get some warmth.
Matter of fact, this thing can really heat up, so it's always better to pull out the cable. Another
thing you have to keep in mind is that when you put cordage inside of something like this, you
could see as I was putting it, loading it into the bucket, I actually had to coil it to have it go in
just like you would a hose. Now what happens there is you're actually creating a very long spiral
with a wind in it, and that means that you're going to develop some cord memory, and if you bought an
inexpensive, i.e. cheap cord that's stiff, has just the really hard plastic PVC-only coating on the outside
instead of this rubberized softer, it's going to tend, especially in cold weather, to not lay flat when
it's played out along your work surface or on the floor, which can create a trip hazard or it's just
a little bit loopy. But you get a lot of cord in a very small area, and this is very convenient
to take on and off the job site and to load it in. You can paint them, make them so it's really
clearly your bucket if you're working with several other trades. So this is an inexpensive, quick way
using pretty much found materials to end up with a great system. Now we have created four other
episodes for you that show four other great methods for winding cords that all sorts of
trade professionals like yourself use. So take a look at those and see if there's anything there
you can use. Make sure to comment in the comments below. And while you're at it, check out this video
where we tell you what you really got to know about cord reels that you mount in your shop, in
your garage area. There's a couple critical factors that really make a difference of how happy you're
going to be with that device. And also check out this other video from our catalog that YouTube
thinks is perfect for you, and so do we. Until the next time, this is Dirt Farmer Jay from DirtFarmerJay.com