We’ll show you one of 5 ways to wind up extension cords. This is a legacy method that has been used for many years in the trades! We know it as the “Daisy Chain.”
This episode features the “daisy chain” method - a series of loops chained in each other - just like a crochet stitch with yarn. This method has been used in the trades, in a wide number of settings, for many years. There are many that swear by it as “THE” way to wind up and stow power cables. We’ll show you how it is done, and the advantages and disadvantages of the approach.
I was first introduced to the “daisy chain” method many years ago on home construction sites. I saw both experienced framing and trim carpenters wind and transport their cables in this configuration. You could wind up cordage very quickly, and it would not get tangled up with other cords being stored or carried with it.
Several years ago, we published a video called “The Best Way to Store an Extension Cord.” It has been viewed nearly 6 million times. Viewers have supplied a list of titles they know this method by:
Daisy Chain Jacob's Ladder California Roll Cord Crochet Construction Roll Chain Braid Chain Roll Engineer Knot Arm Knitting Electrician Knot
To do the “daisy chain” method, lay out the cable in one long line and then bring the two ends together and plug them in. Then go back along the length of the cord until you reach the poing where the cord is folded - this is your halfway point. Mark that point with a permanent marker or with wraps of electrician tape.
This allows you to find the halfway point of the cord from then on and to begin your wind up quicker when you are finished for the day at the jobsite.
Pick up the cord at one time on both sides of the center point, creating a loop. Fold the loop down against the two conductors. With the other hand, reach through the back side of the loop and pull another loop through the first one. Don’t make small, tight loops. We recommend the loops be about 8” to 12” (20 to 30cm) in size.
Then repeat by moving the supporting hand one loop and reach through the back again and grab another length of cordage and pull it through the loop to create yet another loop. Proceed down the length of the cord until the ends of the cord are hanging out a bit and can be plugged together.
For a very long cord, you could “halve the halve” and have four conductors being wound up this way too.
Now that you know how to do it, here are some benefits as well as potential liabilities using this approach.
The benefits are that you can wind up a lot of cord very quickly and it can be stowed in a job box or cabinet, or in a work truck, and it won’t get tangled up with other cords.
If the cord is unwound from the correct end (where the ends are plugged together, NOT the halfway point), the cord will play out beautifully.
And, others that aren’t familiar with this method tend to leave your cords alone on the jobsite!
As long as you are not putting a draw on the cord that is anywhere near its capacity, it’s possible to pull out only the cordage you need. However, this isn’t a good habit to get in to.
Downsides include the cable getting a memory of the loops. This is especially true of cheaper PVC jacket cords that tend to be stiff on their own accord. Add cold weather, and the effect is worse. The cord will tend to not lay across the floor flatly. This can create trip hazards.
Also, if someone attempts to unwind the cord from the wrong end (that is, the middle point), it will end up in a series of knots and loops. This is very frustrating!
If the loops are too small, this can put stress on the conductors in the cable, so larger loops are better.
There is an active discussion (argument?) about whether or not you can run power through an extension cord that is looped or coiled. The short answer is yes. You just need to be sure you are using only about 80% of the capacity of the cordage. This is seen with the ratings that are used on cord reels. Power is routinely run through coiled conductors, but because they are coiled, they rate the capacity of the cable lower than an uncoiled cord.
Whatever method you use, taking the time to coil up and stow your gear at the end of the job pays off in having gear that will last a long time.
While you’re at it, check out these other methods that trade professionals use as well:
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
I'm gonna show you one of five different methods
of how to wind up a cord.
This is called the daisy chain method.
Stick around and I'll tell you all about it.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
This is one in a series of video episodes
that show different cord winding methods
that trade professionals use around the world.
Now, this particular method I call the daisy chain,
but as you can see by this list,
there are lots of different names.
These are all names that have been submitted over the years
by your fellow viewers of what they call this method.
Now, I will tell you,
this is one of the most controversial methods
for winding cords, and I'll tell you why in a moment,
but we've had some really strong comments
of people that say they really don't like this,
and I've had other people that say this is the best.
They've used it in the trades for years,
and it didn't matter whether they're union electricians
or non-union, heavy construction, home framing, et cetera.
There are people that love this method,
and there are others that dislike it.
Well, I'm gonna show you how it's done,
and then we'll discuss the pros and cons.
Well, let's get to it, okay?
All right, so the first thing you need to do
is play out the cord, plug in both the male and female end,
and then stretch out the cord to find the long point
or the halfway point of the cord,
and at that point, you can mark it
using a durable marking tape or a tag
or that sort of thing.
All right, now that you have the halfway point,
alls you're gonna do is create this little noose like this,
fold it down, and grab the two like this, and pull through,
and when you do, that's what you have.
I'll do that one more time for you.
Create the noose at the halfway point,
fold it down, reach through, and there you go.
There's your first loop.
Now, when you do this, don't do little bitty loops,
especially if you bought a cheap cord,
because you're gonna end up with a lot of loopy loops,
and it won't lay flat when it's cold,
so use larger loops,
something like in that range right there,
and then what you're gonna do is grab another one,
pull, put it through, switch your grip, and grip that.
Do you see the loop starting to form?
Grip, pull through.
Grip, pull through, and right on to the end of the cord.
All right, we have now got it wound up.
How does it unwind?
Well, this is where a lot of people get into trouble,
and especially if you have somebody else
that's not familiar with your cordage, the way you wind it,
they tend to grab the wrong place, pull it apart,
and you end up with a series of knots.
Like any of the cord winding methods,
you need to know how it was wound
so you know how to unwind it,
and in this case, the last place that was pulled through
was this right up here, this big loop right here
with the plug in and plug out, and once you undo that,
notice what's gonna happen here.
I can take this and start winding out the cords like this,
and it'll just come unwound, and there you go.
So now you have this all pulled out like that.
Before we get to the pros and cons of using this method,
I wanna remind you, when you first buy your cord,
always buy the best cord you can get.
We really like this Watts Wire Cord.
It is an exterior-rated, rubberized cord
that'll actually oil resist.
Really like the feel and the texture.
It's very soft, and so it's gonna stay pliable
even in lower temperatures.
It's not cheap, but it's a great cord,
and it's an investment in your craft.
Okay, once you have a better cord, when you first buy it,
it's gonna come coiled up just like a hose is
or in a series of loops with a sleeve around it.
The first thing you need to do
is get it out of that packaging,
lay it out in a warm place,
perhaps on a lawn out in the sunshine
or maybe on a driveway or sidewalk.
Let it sit out there for about an hour
and really soften up, get warm,
and to lose the memory from the packaging.
And now you're ready to play it out
and to use whatever method you want to.
Okay, let's talk about those pros and cons.
Well, the pros of this kind of cordage is,
several tradespeople says, when I wind it like this,
other people don't mess with my cords
because they just look at it and go,
I don't know where to begin.
Of course, they know the secret.
You just always unwind what you put in last,
which was the cord ends.
Secondly, another pro for this
is that we've had some people that have said
they've used this on the docks or in gang boxes
where they need lots of cordage waiting.
This will hang in vertical layers
and you can or down flat and they will never intertwine.
So you could have 50 different cords like this
and they won't get hooked into each other.
You can just pull them out one at a time and use them.
So those are both pluses.
The other thing is, you take a relatively large cord,
that's a 50 footer,
and I've now put it into something about this size.
It's got plenty of loops
so that I can hang on something like that.
So that's another plus.
So that might be a reason that someone really likes this.
Now, full disclosure, what are some of the cons
people hate about this?
Well, I've had some very strong words directed towards us
as a result of us publishing about this method previously.
And I can understand some of your angst,
but here's a couple of the complaints.
One, in low, low temperatures,
this is gonna have a tendency to not lay flat.
So you're gonna have loops,
which could become a trip hazard.
Number two, exactly what we just talked about,
it's daunting for new people on the trades
or someone that's been called to fetch and get a cord
and they try to play it out,
they grab the wrong end, knot it all up.
Number three, we've had people say,
well, you're asking for an electrical fire.
That's gonna create a lot of resistance if you plug it in.
No cord is meant to be used all coiled up,
including cord reels and cord buckets.
And you'll find the ratings on those are dropped
for the amount of wattage that they deliver
simply because of the resistance of the wire and smaller.
So this is not meant to be just pull out
as much as you need like this,
and then start plugging in plain
because all the rest of it's still there.
You could do that, it's risky.
If you're doing a moderate amount of power on it,
it's probably okay, but why risk it?
So those are some of the cons that you're going to see.
And that's fair disclosure.
Now, if you'd like to see four of the other methods
that we talk about, you can check out the description below,
take a look down there,
and we've got links for each one of those.
And you can also check out this video right here
that shows one of those methods.
And while you're at it, check out this video
that YouTube thinks is perfect for your interest,
created out of our catalog for you.
Hey, thanks for tuning in today.
Until the next time, this is Dirt Farmer Jay
from DirtFarmerJay.com.