How to Line a Board for Leather Bookbinding // Adventures in Bookbinding

Sparky Deal
161 followers
1 Video ViewยทJul 3, 2023
In this video, I'm going to demonstrate lining boards specifically for leather binding.
However, I'll also discuss grain direction and balancing pull using different materials and different adhesives.
I'll start by lining a couple of boards to be used in a typical full leather binding.
I've picked my boards, so the grain direction is head to tail, and also the lining paper.
I'm using this Canson Bank Layout paper.
It's a very strong, lightweight paper, 45 gsm.
Unfortunately, I can't get it anymore, but I've still got a bit of stock of it.
I'll start by pasting out the thin paper.
Now, I want this paper to stretch as much as possible, so I'll give it a very generous coating of paste.
Notice how I paste out from the center of the paper.
And once I've pasted it out, I'll let the paper relax.
I'll let it absorb the moisture out of the paste, and I'll give it a second paste as well.
Handling wet, thin paper can be quite challenging, so there's a little trick to handling this paper.
Just fold over about a third, and then that keeps the paper rigid and easier to manage.
And now align the unfolded one third of the piece of paper with the edge of the board.
And press that down reasonably firmly so that doesn't become unstuck.
And then unfold the rest of the paper and lay it down.
I think I've managed to make this easy trick look harder than it really is.
The paper will be very fragile, so it's probably best to smooth it down under some rubbing down paper.
I've seen a lot of discussion on the Internet about how much paper is going to stretch.
And a lot of people say that it's unpredictable because of humidity and temperature issues and the moisture of the
adhesive you're going to use.
And this is in the context of pasting down end papers.
So one way to deal with that is if you want to trim up the paste down before you lay it down, is to keep scraps of
the same material and have a piece, a piece that's, well, you could use the end paper as a comparison.
So paste out a piece of the scrap with the adhesive you're going to use on the day under the same conditions and just
see how much it stretches in comparison to the same length of paper.
So you would measure out a piece the same width as the end paper.
And then from how much it stretches, you know how much to trim off the end paper.
So just stand the boards up on the bench to let them dry.
And the first thing you'll notice is that the boards start to warp away from the lining paper.
And that's because of the boards absorbing moisture on one side and not the other.
And that's causing the swelling on the one side, it's causing it to warp away from the lining paper.
So you can see that occurring here.
But then you leave it overnight and the lining paper dries and the boards dry out and then it pulls back in.
So this is what we wanted to happen, is the lining paper has pulled the boards in and that will be used to counter
the pull of the leather once we've covered the book.
I think most bookbinders are a bit geeky, and I definitely start to geek out on this a bit.
So I decided to do some experiments and cut some pieces of paper all the same length of the bank layout in different
grain directions and some pieces of card, the same 2 millimeter card, also in different grain directions.
And then using paste, I pasted them all together just to see what would happen.
And then when I was done with that, I decided to try PVA as well.
But I start with the paste.
So I'll paste out these strips, try and get them equally moist, and then I'll put them on the board.
So the first interesting thing is you can immediately tell the grain direction by the way the paper curls.
And then the second thing is that after you leave it for a while, then the paper relaxes.
So I'll paste the paper out one more time, just get a bit more moisture in it.
And by now, the moisture is soaked all the way through the paper and the paper will lay flat because it's relaxed.
So if you're ever having a problem with a piece of paper curling up and you're having trouble laying it down somewhere,
the best thing you can do is just to take a breather and just let the paper relax.
And then it'll flatten out and it'll be much easier to deal with.
The first thing you notice when we put the paper on the board is that the paper stretches across the grain, which is
what we expected and what we wanted.
But what is surprising is by how much.
So this piece of paper is 200 millimeters wide.
And with the ruler, we can see that it's stretched 5 millimeters.
Of course, in the grain direction, it's still the same length.
It hasn't stretched at all.
Now, this paper stretches a lot, and that's why I use it for lining boards.
And in the strips of paper, the long grain, we see that the paper stretches across the width of the boards.
Of course, these boards are supposed to represent a strip across a book from spine to fore edge.
And we see that boards with the grain direction vertical, like it would be in a book, are warped just like we saw
when we lined the boards earlier.
The next experiment is to apply the paste to the board and then put the paper on the pasted board.
Now, the rule of thumb is to always paste out the thinner material.
Now, the reason being that the paper will absorb the moisture and then try and stretch, but it can't on the thick
board. And so there's a danger that you'll get wrinkles in the paper.
And you can see them forming on the edge here.
However, in this case, what's happened is the board has warped because of the moisture on the one side, which has
stretched out the paper anyway.
And when it dries, it ends up being stretched almost as much as the piece of paper where the adhesive had been
applied to the paper, which is pretty interesting.
The final experiment was to use PVA, which you hope has less moisture.
And I did it both to the board and to the paper.
You can see that crinkling effect happening again there.
Here's the final result.
We'll discard the ones with the wrong grain direction.
And the final result is that the boards that warp the most is the ones that we expect.
So paste with the grain directions in the right direction.
And then PVA where we've applied the PVA to the board instead of the paper.
So if you want to tension a board, use a paste and paste out the paper and let it relax.
And if you don't want to tension the board, then use PVA and apply the PVA to the thicker material and just watch
out for a cockling of the paper.
So let's put a piece of leather on our lined board.
So I'll go through the usual steps.
I'll wet out the leather and then I'll paste it, let the paste soak in.
So I'll face this leather and then go off and do something for a few minutes while the paste soaks in.
And then I'll paste it again and then put it on the board.
Or in this case, I'm going to put the board on the leather.
I thought this would be a good opportunity to do another corner demonstration.
When doing a full leather binding, before applying the leather, you won't know exactly where the corners are, so you
can't really trim the corners.
So what you do is you apply the leather and then once it's on the book, you can apply a little bit of pressure at
the corner to make an impression of the corner and then peel the leather back.
And then using a piece of scrap board and your paring knife, you can trim off the corner.
Notice how I'm doing it at an angle to just get a beveled edge on the leather.
So just go around and do the four corners that way.
Then refresh the paste on the turn ins, and then it's a matter of turning in the leather and pleating the corners, as I
demonstrated in the leather library binding.
Now, leather sort of has a grain direction as well.
It stretches more in one direction than the other.
So the way I think about it is that the grain direction is in the same direction as the spine of the animal.
So when I cut this piece of leather out, I cut it so that the spine went the length of the board.
The leather will stretch a bit in the other direction, but that's countered by the stiffness of the board in the
grain direction.
Here's the board with the wet leather on it.
And overnight, as the leather dries, it will shrink and pull the board flat, fingers crossed.
And with a bit of luck, you end up with a very flat board like this.
As always, if you've enjoyed the video, please hit the like button.
And if you want to be notified of my future videos, please hit the subscribe button.
So until next time, cheerio.
