What is a Book Plough and How to Use it // Adventures in Bookbinding

Sparky Deal
161 followers
2 Video ViewsยทMay 26, 2023
There are a number of ways to trim the edge of a book.
The most common modern method is to use a guillotine.
According to Middleton, the guillotine came into use in England around 1840.
Prior to that, for about 300 years, the dominant method for trimming the edge of a book was a plough.
There's quite a few variations in ploughs, but I guess in common, they all have some sort of press to hold the
text block. And something like this sled to hold a blade and to move that blade across the text block as you go
back and forth, cutting the edge.
This is a nice compact example that's suitable for a small workshop.
So you can flip the lying press over and use it as a finishing press on one side, and the other side acts as the
guide for the plough.
To use the plough, you insert the book so that the trim mark is exactly level with the front surface of the press.
Now run the plough back and forth, advancing the blade ever so slightly each pass.
Now here I'm trimming a fore edge so I can advance the blade a small amount in both directions.
But if I was trimming the head or tail, especially in boards, then I would only advance the blade slightly as I went
towards the spine of the book.
This is because of the shoulders on the book, and I want the shoulders supported by the boards as the blade comes
towards the shoulders.
How fast you advance the blade depends on the plough, how sharp the blade is, the paper in the text block, how
smooth you want the finished surface to be or finished edge to be.
I guess two or three pages at a time is probably typical, and it's probably one of the most energetic activities that
you'll do in bookbinding.
So this nice little setup is not mine.
It's online from the Queensland Bookbinders Guild.
I brought it home to use for this video and to give it a bit of a tune up.
I'm very lucky to own a Frank Wiesner plough and one of his large line presses and a matching tub.
So I'll just do a bit of showing off and show some of the features of this press.
You can flip it over.
So I'll use it this way up when I'm backing and when I'm doing edge work.
And this side obviously has the guides for the plough.
I bought the press and the tub second hand, and then I bought the plough directly from Frank, and he originally sold
that press without the guides.
So he added the guides for me.
So I'll demonstrate trimming a book, marking the trim marks first.
I'll start by trimming the fore edge.
The piece of greyboard at the rear is called the cut against, and I'll also put a piece of greyboard at the front,
which is lined up with the trim mark.
So I'll put the text block in with the trim mark aligned with the top surface of the press.
Because I'm trimming the fore edge, and the fore edge is symmetric in both directions, and assuming my rounded tip
blade is sharp for cutting in both directions, then I can advance the blade both before I go forward and before I go
back, which is a bit faster than trimming the head and the tail.
Here's an example of my normal pace at normal video speed.
Now, my blade is extremely flat and it's well aligned with the top of the plough, so it never rides up on the cut
paper, which can be an issue with some ploughs, and that causes little dents in the edge.
If you're always trying to pull the pieces of paper out of the way, there's always a danger you'll pull one that's still
slightly attached and you'll mar the edge as well.
Once you get past the end paper, then you know to stop.
Now I'm going to demonstrate cutting the head and tail out of boards, so the boards haven't been attached at this point.
There's a lot to be said for cutting in boards, but I'll start by demonstrating out of boards.
Now, because of the swell in the spine, I can't just put the text block straight into the press.
So the next step is to round the book.
In a future video, I'll demonstrate cutting in boards.
That's where the book has been rounded and backed and the boards have been attached.
Even once the book's been rounded, there's still some swell at the spine.
I'm going to deal with that by using these boards that have a bevel on the long edge.
So I'll use those to compensate for the swell at the spine.
Here you can see how the beveled boards support the swell at the spine.
And again, I put the book into the, or the text block, into the press with the front board lined up to the trim mark and the
trim mark lined up to the top surface of the lying press.
As you can see here, the spine is not as compressed as the rest of the text block.
So the best way to trim the paper at the spine is with the blade going towards into the spine so that those beveled
boards support the swell.
So I only advance the blade when it's closest to me before I push it towards the spine.
So I don't advance the blade on the return.
This is more important once the book has been backed and when you're ploughing in boards.
Once you've cut through the final coloured sheet of the end papers, because of the swell, there'll just be a few pages still
attached at the spine.
And the best way to trim those is with a very sharp knife.
Assuming the plough is set up well and the blade is very sharp, the resulting edge is very smooth and requires very
little further preparation before any other edge decoration technique.
I'll repeat the process for the other end of the book.
I'll show some different camera angles to just help see how the process is done.
I really love learning about the variation in edge trimming in different bookbinding cultures and traditions.
The Japanese tradition is really interesting, and they stand on the book when they trim the edge.
Even the ploughs that I've demonstrated today are used in different ways.
I'll put a couple of links in the description to videos of these ploughs being used in different ways.
There's a great video of Stoppan using a very similar plough to the first one I demonstrated in a vertical configuration,
which is really interesting.
And I'll also have a link to a video of Trevor Lloyd using the exact same plough, the Frank Wiesner one, however, in a
different configuration with the line press leaning forward.
To make trimming more accessible cost wise, there's systems that use these circular blades and they just have a holder
that slides along the top of the press, so without the sled.
There's also ploughs that have a sled, but also use a round blade as well.
There's a lot of different configurations.
But I think my Frank Wiesner plough is pretty hard to beat, and I'm pretty lucky to have it, I think.
I hope you've enjoyed this video.
If you have, please let me know by hitting the like button.
I'll do a short video on how I sharpen the blades for these two ploughs.
I'll publish that midweek.
And then sometime in the future, I'll also do a video on ploughing in boards, which is a really interesting technique.
I regularly plough the head and tail of a book in boards.
But until recently, I hadn't really done fore edges, so I want to become more competent at that before I put that in a
video for you.
So if you want to be notified about those future videos, please hit the subscribe button.
And thanks for watching.
