Instruction For Montessori Bookshelf by Dannico

Sparky Deal
161 followers
#DIY #howto #woodstuff
Here is a step by step instruction that shows you how to assemble your new bookshelf. If you have any questions, please don't hesitate to contact us, we would be more than happy to help.
https://dannicowoodworks.com/products...
Hi! Today we're going to be assembling the Danico Woodworks Montessori Bookshelf.
In your package, you should have received piece A, which is the one that we're starting on.
And you should have received all the corresponding parts that need to be assembled in order to build the bookshelf.
We're going to start, like I said, with piece A.
And piece A is labeled with numbers 1 all the way to 13.
And so the first thing that we're going to do is look for piece number 1.
So it's going to look like that.
To assemble, you need to find the sticker.
And make sure that the stickers face each other.
And then you just need to insert the piece.
You may need to use a rubber mallet for this.
You need that there is no gap between the two parts.
So make sure that the parts are flush with each other.
Once number 1 is moving in, you're going to move on to piece number 2 and 3.
So now that number 1 is inserted all the way, we're going to move on to piece number 2 and 3.
Which is in the next line that needs to be installed.
And you will notice that when you find the piece, there's going to be a section that doesn't have a sticker.
And then a side that does.
So again, you just want to make sure that the corresponding stickers line up with each other.
So number 2 needs to line up with number 2 at the top.
And number 3 with each other.
This one didn't need a rubber mallet, but if you want to use it just to make sure that it's fully in, you can do that.
Next is number 4.
The stickers face each other.
I like to start with the bottom piece first.
And then slide it down.
And make sure it's attached. There are no holes here.
Next is number 5 and number 6.
This is number 5 and 6 right here.
I'm going to start with the bottom piece.
Insert it.
And I'm going to use a rubber mallet.
And I'm also going to make sure that it's all staying together.
Next is number 7.
The stickers face each other.
Then number 8 and 9.
All the way. Keep these together like this.
Everything starting with 2 and 3.
As you're working, just make sure that they're staying together.
The last big piece is 11 and 12.
Another thing I want to show is that first I like to put the bottom piece and align it like that.
Tip as you're working towards it.
It's different about 11.
There's going to be a little groove right here, so it's not going to be flush like the rest of these are.
And that's okay. We need that groove in the next steps.
As long as you make sure that the bottom here is fully aligned, then that's fine.
This can stay a little bit higher.
This part is going to go in number 13.
This is a right-sided drawer, so it's going to line up like this once the bookshelf is up.
This is going to be number 1 and number 3.
You're going to lay it on top, making sure that you find where the holes line up to each other.
Once it's lined up, you're going to start lightly tapping around.
The goal is for there to not be any gaps, just like at the bottom here.
Make sure that you do light tapping.
If you do it harder, it's going to raise this part over here.
If you do it slower, it will go in more evenly, and it will be a little easier.
So this side is fully in.
This side is in as well.
I'm going to use a mallet.
This part is fully in.
We're going to stand it up.
There we go.
Next part is C.
The important part about this section is making sure that these act as hooks over here.
You're going to put it right here in front of it.
You're going to slide it down so that this part is over here and here.
This should be flush to here.
What I like to do first is pull down to this bottom part here and slowly start sliding it down.
If you see here, this section has an angle, which means that the groove inside here hasn't fully gone in.
The reason for that is because this is not all the way flush.
What you can do is you can grab a mallet.
If you see, it went a little bit more inside.
We can tap it.
The groove goes inside of 13.
This piece now is fully 90 degrees to the floor, so it's in.
That's exactly what we want.
Now that C is in, we're going to slide D here at the bottom.
For this piece, what I like to do is set it on the ground.
Very similarly, you're going to grab D.
These pieces are going to serve as hooks.
You need to work slowly.
Now that these pieces are flush, we need to make sure that the grooves in D fall inside of C.
Something that I like to do is just raise it with something.
It can be anything, a kitchen towel.
Then, just make sure that it slides in.
These pieces, make sure that they're still flush.
That's it.
You can stand it up now.
We can install the top compartment, the top lid for this part.
You've got to make sure that these two hooks line up right over here.
Then, you're going to pop them in.
That's it.
The bookshelf is now assembled.
We are now going to work on the drawer piece.
For assembly of the drawer, the only thing you will need is a screwdriver.
You won't need a mallet anymore.
Depending on which side of the drawer, these pieces might look a little bit different, but the concept is the same.
This is a left-sided drawer that we're assembling.
First, you're going to grab the big triangle that has the line here.
You are going to dump the screws that came with it.
You're going to need three first.
You're going to attach them right over here.
This is where the screwdriver will come in handy.
You need to make sure that you do not over-tighten.
This part needs to basically just touch here.
As you're screwing it in, you may notice that the screws are a little bit crooked.
That's fine.
Once you screw it in, make sure that this metal piece is fully seated with this plastic piece.
Then, we're ready to insert this piece.
We want to make sure that the line lines up with this one over here.
Then, this part is flush.
These parts align.
If you turn it around, we need to add these.
If you inserted them before, that works too.
The important thing about these pieces is making sure that the little arrow marks the start of where the screw is.
The little arrow will be pointed here.
Like that.
Then, you will rotate clockwise.
Then, this part is fully in.
You're going to do very similar with this piece now.
The narrow piece.
You're going to insert it like this.
Then, you're going to grab one of these parts.
The arrow is pointing towards the screw.
Then, you're going to rotate with your screwdriver.
Next, we're going to slide this part.
There are two sides to this part.
One is a little bit shiny and one is more matte.
The matte part needs to be at the bottom so that the shiny part is what stays on top.
You're just going to slide it down fully.
You see these pieces are flush here.
Then, the last piece is attaching this other last triangle.
Just like we did with this one, we're going to attach the screws.
Again, if you notice that they're not 90 degrees, that's okay.
Again, making sure that the metal is flush and sits right next to the plastic part.
We're going to install it just like we did before.
The holes will line up.
You just need to push it.
There was a piece here.
This was inserted the wrong way.
It was inserted this way rather than with the arrow facing outwards.
It was causing this part not to be fully inserted.
If that happens, just make sure that there's no piece inside here.
If it is, it's inserted correctly.
Now that all the pieces are inserted, just like you did here,
we're going to insert this piece with the arrow facing the screw.
This last piece is easy to see.
The screw is here, so the arrow is going to be just like that.
The other two are right here, just like that.
Then you're going to turn it clockwise.
The other last piece needs to be inserted inside.
That is your drawer.
Now your drawer is fully assembled.
You will need to line up this part here and this part here.
If you can have somebody hold these two pieces, it's easier.
I've done this a couple of times, so I can do it without help.
Once you hear that snap, that means that the drawer is in.
You can just put it like that, and then you can test it again.
Make sure that the soft-close works.
