5 weeks to finish_!_! tambour cabinet with copper leaf inlay + bluetooth

Keith Johnson Custom Woodworking
85 followers
8 Video Views·Mar 8, 2023
To be honest, I'm not a super creative guy.
I don't have sketchbooks full of different designs and ideas that maybe one day I'll
get to building.
So for this cabinet, I merely had an idea.
I wanted to try and inlay some kind of design with copper accents into the front of a tambour
door.
Two things I'd never done before.
And with the help of the Shaper Origin CNC, I was able to bring my idea to life.
Oh, and I had a Bluetooth radio kit lying around, so I figured I could incorporate that
into the cabinet design to combine form and function.
Here's how it all went down.
This video is sponsored by Masterworks.
Oh man, only one piece left.
Better not screw this up.
All right, so I'm starting with some 8 quarter quarter sawn walnut and actually got a little
bit of curl in it.
So that's nice.
So first, cut it to length.
Then I'll head to the joiner to get one face nice and flat and then run it through the
planer.
Get the other side flat and parallel and then one edge through the joiner and then over
to the bandsaw to resaw my pieces in half, which will give me roughly three quarters
of an inch on each side.
I cut down a small piece and then a couple big pieces for the top and bottom of the cabinet.
And as you can see, this is what we get.
That is some beautiful walnut right there.
Then I can stack and sticker it, let it acclimate to the environment, get nice airflow all the
way around on all four sides.
And I always put a scrap piece on top.
That way that top piece gets the same amount of airflow.
And the next day I could head back to the joiner to flatten one face.
As you can see, it did move on me and needed some work.
And then back to the planer, make sure everything is nice and flat.
And then I could move on to setting up my shaper tape so I could use the shaper origin
to cut out my groove and the shape of the top and bottom of the cabinet.
So using some double-sided tape, I can just affix it to my little jig that I made here.
So you might be wondering what this funky domino tape is.
Well, it's actually a uniquely encoded pattern that creates a workspace that the shaper origin
can accurately track its position and where it needs to cut.
It's like GPS tape.
Now with my design, created an illustrator and export it as an SVG, I was able to drop
it in my shaper hub, which puts it right on the machine.
And then I could drop it on my workspace and start cutting.
And since this machine has an autocorrect, if you happen to veer off course, as long
as I just stay on that dotted line, I will be fine.
So I go all the way around.
Now this is going to be the groove for my tambour door.
And now I'll go all the way around the outside for my final shape of the actual bottom piece.
And there you have it.
Now I could work on the top piece.
But first, you goober.
And with that bottom right piece having a little less adhesive on it, I could stick
my piece down and get to cutting.
And this is where I ran into my first problem.
All right.
I'm noticing a couple problems here.
I actually cut this as a prototype before with a quarter inch groove.
It actually needed to be three eighths.
But when I do it with a three eighths groove and I have a half inch by half inch tambour,
it just looks too chunky and it doesn't make the corner either.
I can fine tune that a little bit.
But having it thinner, but still a half inch wide in a quarter inch groove, I think works
better proportionally for this cabinet.
So what that means is these two pieces are no good, but I can still cut them into strips
for the tambour.
And I'll make two new pieces for the top and the bottom.
Bummer.
And I won't bore you with that whole process, but they were both cut.
Here is the second one and the first unneatly stacked on top.
So I've never done tambour before, but I watched a couple of videos, my buddy Bourbon Moth
and Michael Alm from AlmFab.
And on the slats for the tambour, there's a rabbet on the back.
But most guys, it seems, leave that sixteenth of an inch gap exposed.
So the option is to either leave it exposed like that or turn this around so you don't
see it.
What the overhang of that shoulder does is it puts a shadow under there and kind of hides
the fact that that round channel doesn't necessarily line up perfectly with the squareness of the
tambour slat.
So I was going to do that, but I think I am going to do it like this.
Meanwhile, Shop Cat Jerry and Shop Cat Lola were doing what they do best.
All right, what I've got here is a test piece that with the shaper I cut out all these hexagons.
Some are recessed, some are just the outline.
And then I tried some copper leafing in there.
This was all just an experiment.
Then I went back in and readjusted this design, flip flopped some things, deleted some things.
I just wanted to see the scale of this and just experiment with the copper leaf a little
bit.
So definitely have some improvement to make there.
But I think we're ready to move on to the next step, which is the tambour strip.
So I have here my pieces kind of all milled up to three eighths of an inch.
So what I want to do is lay these out kind of how I want them on the door, trying to
get the grain color to kind of flow.
Now this is pretty much the full length of my tambour.
This is the center where the pole will go.
It's the left side, the right side.
But I'm going to be taking out a saw blade's width on every strip I cut.
So I'm going to need a lot more material than this.
And then I could start ripping.
Now I did cut these a hair oversized just so I could run them all through the planer
at the same time at the end to get rid of any burn marks.
But what I did realize is despite the fact that this was quarter sawn, there was still
a lot of tension in this wood.
So a lot of pieces went haywire on the table saw.
So I ended up using a lot more material than I expected, but not that big of a deal here.
You can see I'm just fishing and sorting out any bad ones with curves, bends, bananas,
whatever the case may be.
And just trying to get a nice flow of grain and color all the way across.
Next up was to cut all my tambour strips to final length.
So to do that, I'm using a crosscut sled on the table saw.
I'm squaring up one end of all of them.
I finally realized it's easier if you cut two pieces at once.
Makes things a little quicker.
And I think I actually ganged three up on that one.
Watch out now, Mr. Efficient.
And then I could set my stop block to eight and a half inches.
That is going to cover the height plus the rabbet on the ends that will go into the tambour groove.
So once that was set, it was full speed ahead.
Line them up.
Cutting, cutting, and more cutting until all done.
And I was left with a pile of scraps.
Then I needed to rip the tambour strips that would go in the very middle where my poles would go.
These are a little bit wider.
They are one inch wide.
And then I went and numbered all of my tambour strips like a maniac.
Not sure this was really necessary, but I like to keep things in order.
And then I could start building the jig to assemble my tambour.
So I'm just using some Baltic birch plywood to make said jig.
So I clamped a big piece down and then I ripped up some strips and screwing those down.
And I need to make sure this jig is perfectly square.
That way the tambour strips don't somehow skew sideways.
I also want the top and bottom rail of this jig to be the exact distance to match the height or length of all of the tambour strips.
I'm using a square again, making sure that I didn't put that in crooked.
And then I could just tack it in place and screw it down securely.
I'm also adding some stop blocks at the end, which will be equal to the length of the tambour.
And then what the heck, I'm just going to cut right into the jig that I just made.
Well, actually, this does have a purpose.
I'm pulling out a couple of pieces, top and bottom, which will allow me to slide in some wedges and wedge the entire assembly nice and tight, which you'll see shortly.
Now, because of the thickness of Baltic birch I had, I needed to look out forearm cams back.
I needed to build up the middle just a little bit.
So I put down a piece of quarter inch plywood and then I started sanding.
Each one of the tambour strips needed to be sanded on the sides, not the top or the bottom, because I'll get those with the random orbital sander.
But the sides all needed to be sanded.
And again, I smartened up and said, oh, if I gang two pieces up, it'll be a little easier.
And then once those were all sanded, what I wanted to do was prefinish those edges with shellac, because once the tambour is together and glued to the canvas, it will be very difficult to get in there.
So I applied two coats of shellac, maybe three sanding in between on both sides, which are actually both edges, the inside and outside.
And then I could start laying them in like piano keys, one by one or two by two.
You could see I put my one inch centerpieces in there as well until I'm all the way out to the edge, just kind of giving them a little hammer time, just making sure they're nice and flat.
And then the wedges that I mentioned, this is going to push that block nice and tight and basically act as a clamp to pull everything tight together and make sure there are no gaps.
I'm actually angling these screws in to give me a little bit more clamping pressure as well.
And you'll also notice all my strips are slightly proud of my jig.
That way I could hit them all with the random orbital sander front and back.
Well, the fronts I'll get after I do the canvas and flip it over and then I could lay out for my canvas.
I'm basically leaving nine sixteenths of an inch top and bottom.
That's just giving me enough clearance top and bottom so the canvas doesn't come anywhere near the groove for the tambour and interfere with the operation of the door.
I'm also adding a quarter inch clearance on the center panels, the one inch center panels.
That way the canvas doesn't extend past those either.
And a wee bit of clearance on the ends as well.
Probably an eighth of an inch or so.
Nothing too drastic.
Oh, hello, green tape.
Now, as accurate as I might think I am with a roller and contact cement, the likelihood of me going over my layout line is pretty high.
So I'm using some green tape to mask that out just to make sure I don't have any contact cement go where I don't want it to go.
And that goes for the ends as well as the middle.
And then I could bust out the black canvas, which I grossly overestimated how much I would need.
Indeed, I did.
Now, this is just black canvas.
I bought it, Joanne Fabrics.
It's the only one they had there.
They have other colors.
I just wanted black since that goes nicely with walnut and copper.
And then with my piece cut to size, just a hair oversized to overlap the green tape a bit.
I could lay down the contact cement, which I apologize.
I forgot to turn the camera on, but I applied generous amounts of contact cement with a paint roller on the fabric and the wood itself.
Now, the reason I chose contact cement over wood glue in this application is I didn't want to introduce any moisture into these tambour strips and risk any more wood movement like twisting or cupping.
And to be sure I had nice, even contact, I'm just using this fast cap roller.
And then when that was all dry, which is pretty much immediately, I used a straight edge to trim the excess, which overlapped the green tape.
And then I could peel that all away.
Once the sides and ends were done, I could do the same in the middle.
And just like in kindergarten, you could ball up the excess and flick it like a booger.
Now, the moment of truth.
I could release the tambour doors from their confinement and see if they actually, well, worked.
Being able to roll them out of the jig was already a good sign.
And I breathed a huge sigh of internal relief.
But that victory was short lived as I had to turn the doors over so they were face up so I could sand everything and start inlaying my design with the shaper origin.
So the next project was to extend my work surface so I could lay down enough domino tape for the shaper origin to have an adequate workspace.
So this took a bit.
It was some plywood.
Everything had to be nice and level with the top of my tambour.
As you can see, my tambours were slightly proud of my jig, but now my jig and the extended work surface needs to be flush with it.
And once that was done, I could lay down my domino tape and establish my new shaper work area.
And with my design loaded into the shaper, I could click the screen and drop it in.
Now, I had set a couple of pieces of tape down so that I could lay out exactly where this would be perfectly square to my tambour.
And, well, I screwed up big time, but I didn't realize it until I had cut a few of the hexagons.
And you see that?
Oh, yeah, that's right off the bottom.
I accidentally aligned it up with the bottom of the tape and it should have been in between those two pieces of tape.
So after a childlike tantrum, I decided to just push on and come back and fix that later.
So I adjusted my design to the correct position and started cutting all the hexagons.
Now, I had a one eighth inch bit in there to remove the majority of the material and then came back with a 16th inch bit to get the corners as square as possible.
So here's with the eighth inch bit.
And then after the cleanup, much more square and crisp.
Now, it's a round bit, so you can't get perfect, but pretty darn close with the 16.
Then I just came back with a hand sander to get rid of all the fuzz.
And as you can see, I had some hexagons that were carved out completely and some that were just outlines.
And there were big ones and medium ones and smaller ones, too.
And look at these two still sleeping the day away.
Whoa, that lumber has gone up four dollars a board foot since I quoted this job.
And that finish used to be.
And now newsflash, everyone.
Inflation is real.
And despite prices coming back down since the height of covid, they are still high.
And I'm sure you've noticed they are steadily rising again.
Now, I'm just a sole proprietor, small business owner.
I build furniture and I film the process to share it with you.
And I've never really been good at investments or the stock market or French poetry or cribbage
or using epoxy without getting it all over my hands.
But nevertheless, when it comes to my financial future, it's becoming all too real.
The older I get and finding a way to have my money out there working for me
instead of against me is critical.
And that's where the sponsor of today's video, Masterworks, can help.
Now, a typical portfolio of stocks and bonds has already lost around 20 percent this year,
according to Goldman Sachs.
And my personal 401k has taken an even bigger hit.
It's 2008 all over again.
But research is showing that banks are investing 30 to 50 percent of our money
into alternative assets that can actually be helped by inflation.
Assets like what, you might ask?
Well, like fine art.
Well, I wouldn't consider this fine just yet, but I'm working on it.
Now, instead, how about paintings from legendary artists like Picasso, Banksy and Monet?
Data shows the last time inflation was this high back in the 70s and early 80s when I was
yay high, fine art still kept increasing in value by an average of 17 and a half percent per year.
In fact, contemporary art prices outperformed the S&P 500 total return by 164 percent for
the past 26 years.
Masterworks can help you diversify your portfolio in fine art for a fraction of what billionaires
pay to purchase artwork.
Now, Masterworks makes it possible for people like you and I to invest in shares of this
very same contemporary art.
That's just wild to me.
Now, as recently as early October, Masterworks sold a painting for 21 and a half percent
net return.
Now, as inflation keeps raging and demand is growing, Masterworks actually has a wait
list right now.
But my subscribers can skip the wait list using the link below.
So check it out and diversify your portfolio by investing in fine art with Masterworks
at masterworks.art slash Keith Johnson.
That's masterworks.art slash Keith Johnson.
And one day you might even see this on there.
All right, then it was time to do the repair.
I was going to do a patch, basically just fill this in and you'd never see it.
Unfortunately, anytime you have a cross-grain patch, you always see that scene.
But I figured I'd make the attempt anyway.
So I put one little strip in there and then with some CA glue, and then I slid the other
strip in on the other side.
Once that was dry, gave it a light pass with a block plane, hit it with a random orbital
sander and there you go.
Not great.
So I decided to get crafty and in an homage to my buddy Nick Key at Key Woodworks, I went
back into Adobe Illustrator, made a patch, put it back in the shaper and came out with
this.
It's obviously not an exact match to his logo, but an homage nonetheless.
Here's to you, Nick.
Next up was working on the copper leaf inlay for all those hexagons I just carved.
And to push that inlay down into the recesses of the hexagons, I made these little keys.
These will also be used to cut out the actual inlay.
The first one was a hair loose, so I adjusted at five thousandths and that fit in nice and
tight.
So that one got the stamp of approval and I made one for all three sizes.
OK, this was my first attempt just to practice piece.
You can see how wrinkly and how this leaf didn't stick to the adhesive.
So that was this stuff.
Super fragile, difficult to move around without breaking and wrinkling.
And then my buddy Paul at Copper Pig Fine Woodworking turned me on to this stuff, which
has a backer.
So you can see the leaf is stuck to this backer sheet.
So when I stick this down on the adhesive and then I can just peel that off.
And unfortunately, I didn't get the flaky foil out of the way soon enough before Lola
had to go sticking her nose in it.
Literally, I milled up some bigger panels of veneer, pretty much the size of the actual
sheet.
It takes about a half an hour to dry before we can apply the foil.
But let's get it on there.
Now, this adhesive is water-based and it goes on purply blue.
And when it dries clear, then it's ready to go.
Well, unfortunately, because it's water-based, that thin piece of veneer is curled up like
a canoe, which is why I'm glad I taped down the other two pieces, keeping them nice and
flat.
And then it was gilding time.
The adhesive was dry and now I could lay the foil down.
Now, I had done a few tests, which you can see off to the side, but this was still all
trial and error.
As you'll soon see, it was a lot of error.
Oh, help me, Rhonda.
That could have gone better.
So I have this gilding brush, which helps kind of smooth everything out.
You can also see the texture of the walnut coming through, which I wasn't happy with
at first, but then I started to warm up to it and I liked it.
It gave it a little more texture, a little more character.
Now, on the second piece, I used a white Scotch-Brite pad to burnish it and that produced much
better results.
That's like perfect.
And then a few swipes with the gilding brush to smooth it all out.
Now we're ready to start cutting some inlay.
Now, this copper leaf is very prone to burnishing and damage.
So I put a piece of the tissue paper back on top while I had my little template on there
to cut it.
I tried it with a utility knife, then tried it with a chisel.
I found the utility knife was just easier.
You can see I've cut a bunch of these already.
Now you might be wondering why I didn't use the shaper.
Well, I was just worried it would start tearing things up and it would be a lot slower.
So I just went like this.
It took me, I don't know, probably a half an hour to cut all of these out.
I needed like 60 of them.
Taskmaster Lola made sure I wasn't sloughing off and then I could glue them in with some
Starbond CA glue.
Now, there are some inherent issues with using this.
As you can see, some of that adhesive kind of goes up the sidewalls of the inlay, which
can get a little sloppy.
But all in all, it worked pretty well.
As long as I was careful.
Well, except for there, you see there's a little drop of CA glue on the leaf, which
is kind of a bummer.
Now, I did have to repair some of these later on.
Some had scratches and burnishes.
I'll show you how I did repair those later.
But in the meantime, let's just keep rolling with these and one last one.
And you can also see the texture on the foil or the texture of the wood coming through
is at a 45 degree angle.
I tried a couple of different ways, horizontal, vertical, and the 45 degree angle seemed to
look the best.
And with those done, I could brace myself for the next arduous task of slicing all of
those inlays along the seams of the tambour so they fold around.
Now, because some of these tambour slats were so tight, I couldn't actually see the joint.
So I put a piece of paper in there to show me where it was and then use that as a guide
to slice the inlay.
Now, unfortunately, on that one, I probably should have centered it a little better.
So it wasn't that little nick in the corner, but oh, well.
And that's just how I did this.
I set a ruler up and used an exacto knife and just went down and sliced through that
veneer until it was able to break free and the tambour was able to roll freely.
And I definitely had some issues with this.
Trying to hold that exacto knife perfectly perpendicular to the edge of that ruler was
tough, and I definitely had some cuts go off the rails a little bit.
And I'm not ashamed to admit it, but it started to roll nicely.
So that was good.
My vision was coming to life.
Then I could finish up the second door and now show you exactly how it looks and how
it rolls.
And now to seal all the gold leaf with this sealer.
I wasn't too concerned with being sloppy here, and I actually use this to seal the
sidewalls of all the inlays and the top.
You can be a little sloppy there.
It's all going to get sanded off.
And then I could head to the table saw and cut the rabbet in both of the tambour doors
top and bottom.
I'm using a quarter inch dado blade for this.
I'll make one pass on each side.
Then I can move the fence over.
Now, since the groove for the tambour doors is five sixteenths of an inch deep, the rabbet
is three eighths of an inch.
What that does, it gives that one sixteenth of an inch reveal all the way around with
that cut.
And then I could do the official tambour slide and roll around the corner test.
Well, it seems to fit nicely.
Now let's see how it operates.
That's a little rough.
This side is, yeah, that's a lot rough, a little sticking point, but let's clean that
up.
We'll grab the shoulder plane, take a few shavings off of there, and that should operate
much better.
Ah, there we go.
And once this thing is all waxed up, that should be footloose and fancy free.
Next, it was time to get work on the internals.
Now, this was a complete design on the fly situation.
I had nothing sketched out ahead of time.
I knew the Bluetooth radio kit had to fit in there somehow, the speakers and the manifold,
but I figured it should be leaned back a little bit.
When you open it, it's easier to read.
So I eyeballed it at about 15 degrees, and then I could cut the top and the bottom at
said angle and then check it.
It popped the top on, and yeah, that looks about right, I guess.
Then I could start laying out for the control panel, making sure that centered and seeing
where I wanted the speakers to be situated as well.
Now, the speakers had kind of an odd shape.
They were square, but were bulging around all sides.
And I wanted these to sit in some kind of a walnut mount to have them proud of that
angled piece.
So we're using the shaper.
I just kind of drew out a piece that was the same shape, but only larger and then free
it from its double sided tape imprisonment.
And there you go.
It's just a little bit bigger.
So I'm using that as basically a template to flush trim a piece of walnut, which will
allow me to get the correct measurements and protrusion of said speaker mounts.
And in order to do that, I'm just going to double stick tape that little piece of walnut
to the angled divider thing, stick a square there and then measure comes out to two inches.
So that's how thick my piece needs to be.
But I do need to make a new template with a cut out for the speaker.
Jerry, would you hand me that bit, please?
Yes, the quarter inch up cut.
It's in there.
Check on the bottom.
Oh, God.
Well, he did eventually find it.
Now, this new template I'm cutting is pretty much the same as the old, but it has a cut
out in the middle for the speaker to slide into like that.
That's a nice tight fit.
That little notch is for the speaker wires.
All right, now let's do the same thing on some two inch thick walnut.
Now, the bit I had wasn't able to go the full depth, which is why I needed the template
so I could flush trim these.
Once I had routed them at maximum depth, I could head over to the bandsaw to clean up
all the waste around as close to my layout line as possible and then head back over to
the router table to flush trim them and then over to the drill press to clean out that
giant center nodule and then back to the router table to flush trim that edge on the inside.
Nice and clean.
Now, to cut the 15 degree angle on these speaker blocks to match the inside divider that is
at 15 degrees, I created this little sled for my bandsaw and to affix them.
I'm just using some CA glue.
You can see I have some layout lines there.
I want to make sure these things are perfectly square going through the bandsaw.
And then it's just a matter of riding along the fence.
And there's my speaker mounts with a 15 degree angle on the back.
That way they will be affixed to the middle divider and they will be perpendicular with
the ground or table or floor.
Now, this middle divider was a little tricky on how I was going to attach it.
So I'm using the Lomelo Zeta P2 and the Clamax connectors, which tighten with the use of
an Allen key.
So that makes it pretty simple.
Well, I say that now, but you'll see later I just ran into some issues due to space constraints.
And once all the slots were cut, I could then drill for the access holes for the Allen key.
Now, there was one little knot on the top of the top piece.
So I'm just using some copper powder and epoxy here.
So that'll buff up nicely and have a nice little copper accent to match the other copper
accents.
Now, I could lay out my speaker mounts on the actual divider in order to cut out the
holes that would allow the speakers to go all the way through.
Now, these holes could have been caught with a Forstner bit over on the drill press.
But since I had the file already made, I figured why not make it perfect using the Shaper Origin.
So with a touch here and a touch there and we could make the cut out in no time and then
a quick dry assembly so I could figure out which way I wanted to mount these speaker
mounts.
Now, I thought maybe angled upward would help better with sound, but angled squarely.
So they're perpendicular, definitely look better.
And with that decision made, I could cut that middle divider to final length by squaring
off both ends at the table saw.
And whilst at the table saw, I figured it was a good time to cut the end supports that
will basically make this inside divider a big H, as you can see here.
And how's that for iPhone's autofocus?
Oh, gosh, shoulder cam.
Sorry about that.
Jerry was running the camera.
So with those layout lines traced, now I know where I can pre-drill my holes for fixing
screws into the sides there.
So I'll drill from one side to get a nice clean hole, flip it over and then countersink.
And just to warn you, this project has basically every fastener and adhesive in my arsenal.
You got regular screws, pocket screws, lamello connectors, dominoes, rivets, brad nails,
magnets, chewing gum, wood glue, solder, epoxy, contact cement, CA glue.
Well, all right.
Maybe it doesn't have rivets.
And speaking of those pocket holes, here we go.
This is how the end pieces will affix to the bottom of the cabinet.
And what I was hoping was the top of the cabinet.
But you'll see later why that wouldn't work.
So with those drilled, then I could drill my holes for my speaker mounts.
And then I had to cut up this little trim piece, which I'll let myself explain why.
So as you can see, I drilled these access holes for the Allen keys in the wrong side.
So just cut this piece with a 15 degree bevel on it to match the bevel of this.
I'm just going to stick that in there.
Now it becomes a design element.
And then with a mix of CA glue for that instant bond and some wood glue for the permanent bond,
I could affix that little spray activator.
Gets things moving even quicker.
Now to hide the track for the LED lights, which will be affixed to the underside of the top.
I'm just adding this little walnut valance, if you will, just to hide that using some
23 gauge pin nails and some clamps and glue to hold it all in place.
And then I could work on the mount for the control panel manifold plate thing.
And I was able to design this right on the shaper with the onboard controls.
Now we can test the fit.
And after a little layout, I could place the mounting block in place and mark where I have
to cut out so that the radio and wires and controls and all that can slide through.
To cut said hole.
Oh, wait for it.
Battery cam.
That's a new feature.
I use three different tools to use a drill.
I used a jigsaw.
Oh, and a multitool.
Yeah, I could have taken the sides off and done this all with the jigsaw,
but that seemed like too much time.
And yet it took way longer to do it this way.
And I had to take the sides off anyway to cut this little notchy notch for the LED wire to
slide through.
All right.
Next up was to drill the mounting holes all the way into the speaker mount.
So with some double sided tape, I got those perfectly in position.
And then from the backside, I could pre-drill some holes and get those countersunk.
Then I could actually drive some screws through to secure these in place.
Now, this is just temporary.
These will be taken off after to finish sanding.
And by after, I mean right now.
So we'll get this front sanded.
That way we can get this front control panel mount thing in place.
I'm just using a ruler and some tape to get it laid out and perfectly square.
Want to make sure that thing isn't crooked at all.
And then with a couple of beads of glue all the way around,
making sure I don't get any squeeze out.
You don't need much glue here.
Make sure it's square and secure it in place.
And then I could glue on the speaker mounts as well.
You can see the tips of my screws are protruding through the back.
Those are basically my alignment.
So I know since I pre-drilled these holes, they should drop right in there.
And I know they'll be in position and square.
I actually wish I had pre-finished these and that front panel separately.
It would have made it easier and got a better finish on it.
But lesson learned.
And then with everything lined up, I could firmly secure them with the screws.
And now for the mini side pieces that will basically
hide the tambour as it goes around the back.
I need to get a little creative with this, which is why it has an angle on it.
The cabinet itself was really tight in how everything fit.
So I needed to be very mindful of the operation of the tambour so it didn't rub
and yet stay within the confines or dimensions of the cabinet.
Now to be able to access everything from the back of the cabinet,
I cut this access panel using the Shaper Origin.
And then I could cut slots in the back panel for dominoes.
Now these will be used to affix those little wings that we just cut a minute ago.
And then I cut corresponding slots in those wings.
Now I cut one on the loose setting and one on the tight setting.
That way I had a little maneuverability during glue up.
Here's a little fit.
Now, as you can see, there's a two millimeter offset just to
give it a little shadow line back there.
And then I could get to gluing up.
Anytime I'm gluing up something with dominoes,
and at least one side is on the tight setting, I always glue those in first.
That way they're done and I'm not fumbling with gluing up two sides during the assembly.
Now I also cut this other offset panel on the shaper,
which will allow me to put the access panel in with some magnets.
So I mark that and cut it.
I'm actually going to put a little rabbet on the bottom,
which will slide into the groove on the bottom side of the cabinet.
Then with everything in place, a little glue, a few 23 gauge pin nails, and a lot of clamps.
And how about a little finger hole?
So popping off that access plate is much easier.
So drill that out on the drill press and then using a little round over bit, I ease that edge.
And then it was all about the holes for the magnets.
These are quarter inch magnets.
So quarter inch holes in the panel, corresponding holes in the actual back of the cabinet.
And then a little CA glue to secure the magnets.
It was a really tight fit anyway.
As you can see, that CA glue just adds a little more strength.
And then we can test the fit.
And as you can see, there's a little reveal all the way around.
I don't want it perfectly tight in case there's some expansion and contraction.
And while I glue this up, a huge thanks to my good friend,
Paul from Copper Pig Fine Woodworking,
who has inspired me to push my design and creativity to the next level.
He was definitely a lifeline for me on this project from design advice to stress therapy.
Be sure to check out his amazing work and creativity on Instagram.
I'll leave a link to his page down below.
Now, since there was no easy way to attach these side wings to the top and bottom of the cabinet,
I figured I would use some copper pins in ascending or descending order.
So I went from a quarter inch to three sixteenths down to an eighth.
That way they kind of follow the angle of those side pieces.
And then with the wings clamped securely in place,
I could now transfer those holes down into the wings.
And then I could make the copper pins.
I'm just using my belt sander here to kind of round off the top
and then chuck it up in my drill at high speed and go all the way up through the grits.
220, 400, 600, 1200 steel wool.
And then these sunshine polishing cloths.
Can you see yourself?
Oh, yeah.
All right. I am not an electronics guy.
So this is not a tutorial of how to hook up this Bluetooth radio kit.
But if you go to the DIY audio guys page, which I put a link to below,
he is the one that has the best video on how to assemble this kit.
Now, I actually bought this kind of piecemeal,
but you can buy all the components, including the battery pack, etc.
as one big kit.
And I'll link that below as well.
All in all, it was pretty easy to put together with his video
because the instructions that come with it are quite lacking.
Then it was time to get all my components broken down and masked off for finish.
Now for the finish, I will be using dewaxed shellac.
This was also a great recommendation by my buddy Paul at Copper Pig.
This is by Wellermart.
And instead of mixing it with denatured alcohol, you mix it with grain alcohol.
Makes it less toxic.
Once dissolved, it looks like this.
And I'm just using an HVLP sprayer that I picked up on Amazon for 50 bucks.
It worked really well.
There's a link down below if you're interested in that.
Comes with a 1.3 millimeter tip.
You can buy other tips as well, but this sprayed really nicely.
I was very happy with it.
And I gave everything three coats, sanding with 800 grit in between coats.
I mentioned earlier that a few of the copper inlays needed repair.
So all I did was cut the foil to the exact size, put some adhesive down,
laid it on top with that tissue backer still in place.
And then using a brush, I just kind of burnished it and smoothed everything out.
And then with some incisions, make sure the tambour folds.
And it was done.
It worked pretty well.
Now for the tambour doors themselves, I came up with this little idea of
taping them to a roll of paper towels.
That way it would keep everything open.
And it ended up working out pretty well.
And now that all the pieces that needed to be pre-finished were pre-finished,
I could do a little glue up and assembly and finally start to get this thing together.
Now to attach this middle unit to the bottom.
It was just a matter of putting it on the Clamex connectors.
And I did put glue on there.
I didn't show it, but I did tighten those down and then drop a few pocket screws in.
And then I wanted to make sure to wax up the tambour doors nicely.
I put a few coats of wax on there.
This should provide the best tambour rolling, gliding operation possible.
And then it was everybody's favorite time.
Total boat, baby.
That's right, little KJ.
Some Total Boat Fixo Epoxy.
This gives me plenty of open time and superior holding strength.
Now you can see there's some domino slots in the bottom back there.
I'm going to use that to attach the back panel.
I'm not sure I showed those being mortised out.
So I'll just drop that in.
Make sure I clean out any squeeze out and then get those clamped down.
And then I can flip this thing over and put in those brass pins that we made before.
Now, since the brass pins on the bottom will never be seen,
these ones were actually going to sand flush and then put the finish over.
The ones on top have that domed shiny appearance
to give that tactile feel and the nice design detail.
Speaking of design details,
I wanted to make some custom unique poles for the tambour doors.
So I wanted them to be walnut, of course, but then also add a copper accent.
So with my little harbour freight lathe,
I was able to turn down this little, well, rod, I guess.
Drill a hole in the end and then using some Total Boat 4 Minute Epoxy,
I could slather that in there and put a little quarter inch copper pin,
then using a block to make sure I press out all the air and epoxy.
Once that was dry, then I could hit it with the carbide turning tools by Woodpeckers.
These things are great if you don't know how to turn,
because I do not and they make me look like I know how to turn.
Then I could buff everything while it was still spinning and cut it off.
And there you go.
Next up was to dye it with some India ink.
As my buddy Paul says, the look of walnut, copper and black is such a classic look.
And man, is he right?
You can actually see on these doors that some of the outlines of the hexagons,
I did go in there and dye those black just as another added detail
and a little countersink there just to collect any adhesive pooling.
Then I could chuck up the pole in the drill press and give it a good waxing.
Shiny.
And then with surgeon like precision,
using a toothpick and getting some Total Boat Epoxy in there,
then I could finally install these little poles.
Now, one thing I didn't consider is where the doors meet in the front.
There needs to be a positive stop.
That way, the doors always close in the exact center.
Now, there's a positive stop in the back to prevent them from opening too far.
And that's the actual access panel and the other secondary panel that was glued onto it.
But the front was a different story.
So installing a copper pin would create a positive stop.
However, I also needed to glue on some little walnut blocks on the back of the doors,
which would contact that copper pin and force the doors to stop exactly where I wanted them to.
And with that little detail figured out,
I could move on to finishing up the Bluetooth radio part of this build.
So that just involved taking the circuit board and mounting it to the risers
and then installing the battery pack and the rechargeable batteries as well.
And then I could get those charged up.
Now, if you do not use the battery pack with this kit,
you will have to plug in the DC power connection in the front of this all the time to power it.
So the batteries are definitely the way to go.
Now, another design problem I ran into is when the doors were closed in the front,
because there was a little slop in the track,
it was pulling it back and they weren't coming nice and flush out to the front edge.
So introducing this little curved wedge, which I cut on the shaper, actually,
then I'm going to glue in place.
And what this will do is as the doors come together,
it will push them out right towards the front and make them nice and flush and even.
Then I just popped a little block in there to get everything nice and tight while that glue dries.
Next, I could actually start installing all of my electrical components.
This little foam gasket here supposedly prevents vibrations from the control panel.
And then it was time for the LEDs.
Now, this is a motion activated.
I planned on installing this inside the cabinet in the back
so that as soon as the tambour opens and goes by it,
the lights will come on, which as you'll see, it does work.
Unfortunately, it only stays on for 25 seconds.
So, yeah, I wasn't really planning on that.
For some reason, I figured it would just stay on until I close it.
But anyway, the LEDs can easily be cut to length.
So I'll stick those down in the channel.
And then I made this little mounting block that will fit inside the back of the cabinet
very carefully.
Then I can screw it to secure it and then pop that sensor down in there.
Now, unfortunately, because all the electronics that are going back there
and the access hole in the back is very small,
I couldn't get my hand in there to tighten those Clamax screws on top.
So I drilled a few in the front and then we'll add some copper pins
for accent design details again.
But first, let's get this control panel installed and then the speakers.
I had to do a little soldering here to get these wires connected to the speakers,
which was fun.
I've never really done that before.
I'm pretty sure you're not supposed to see smoke, but I might be wrong.
And then it was just a matter of fishing these back in through.
Now, I was able to find some aged copper screws for this online.
Unfortunately, they were all slotted.
I couldn't find any Phillips or Torx, but that's OK.
I still like the look of the copper screw instead of just a standard black screw.
And then I made sure to clock all of my screws vertical.
Now, with most tambour cabinets, you can slide in the tambours from the back
and then remove them if necessary.
But since these had one inch tambours in the middle,
that prevented them from rounding the radius on the corners.
So I had to install everything together, doors in, and they would never be able to come out.
So this got a little tricky.
I had to hook up the LEDs.
I had to install the doors and then drop the lid on.
So it was kind of a three or four hand operation.
So using some TotalBoat Fixo Epoxy, give me a little more open time.
Make sure I thread that LED through.
And then I have to get the right side tambour door installed
and then try to get the top of the cabinet lined up with the Clamax connectors,
the tambour doors and the dominoes in the back.
It definitely took some finagling, but eventually I got it.
And then obviously, I wanted to make sure I tested the doors first
before I really secure everything.
Those worked OK.
So now I could get to those Clamax screws, which will firmly pull down the top.
Now, as I mentioned way earlier, the reason I couldn't get to those pocket screws on the side
was there was no way I could screw up with the tambour doors there.
But that's OK.
With the epoxy and the lamello connectors
and then the pins that we're going to put in here,
this thing is plenty solid.
Oh, and there's dominoes in the back, too.
And speaking of those copper pins,
so with some TotalBoat Fixo Epoxy yet again,
put a little bit in there
and then I put a furniture pad on the bottom of my mallet.
Make sure I don't damage anything.
Drive those just proud of the surface.
I just want a little dome there so you can feel it with your finger
and you'll notice it when you look at it with your eye.
So after the quarter inch one, then the three sixteenths
and then the one eighth, the little guy.
And then pretty much rinse and repeat on the interior
to plug those holes that I used to get to the Clamax connectors.
And then for some shoes on the bottom, I just picked these up at Home Depot.
I think they are one and a half inch diameter leveling feet.
They're rubber nonstick, just like my favorite frying pan.
Oh, and one more thing.
Install the diffuser on the LED track.
Make sure that light isn't so harsh.
And now this thing was finally done.
Who ate my seltzer?
Well, there you have it.
This one took way longer than I thought it would.
You know, due to my normal production schedule
and the fact that I had to design on the fly
and all these things I'd never done before.
But overall, I'm very happy with it.
There's definitely some things I would like to improve upon
with the copper inlay and how I do that.
I'm just not quite sure how I would.
But I really like the ultimate look of the cabinet.
The function of the tambour, the radio itself.
These speakers aren't that great.
It could really use, you know, a sub woofer for some more bass.
But for what it is, it's not too bad.
Now, there are no plans for this because, well, I never had any myself.
But if you wanted to buy a Bluetooth radio kit,
there's a link down below to check that out.
Maybe build your own cabinet and just experiment.
Sometimes the smallest idea can lead to the biggest thing
and open up more ideas and more ideas.
So I'm definitely going to do another tambour cabinet with inlay.
But next time, it's not going to take as long and it won't be a Bluetooth radio.
Thanks so much for watching.
If you'd like to, subscribe, share, like.
I'd greatly appreciate it.
We'll see you on the next one.
Whoa, grand razz.
A little zazzy for me.
