When you hang a ceiling fan, it needs to be right. Use the right support method to assure your fan will stay put, providing air movement and aesthetics too!
Ceiling fans are hardworking devices that look good too! To assure they can safely stay on duty, they must be installed securely using the right support approach.
Because there is combined static weight and vibration when the fan is being operated, heavier-duty boxes and screws must be used than are typically used for installing outlet, switch, and junction boxes. Fans can weigh from under 10 lbs. (4.5 kg) up to 80 lbs (36 kg), depending on the model and accessories. Add the torsion that occurs when the fan is operated, and the fan better be more than adequately supported and attached to its mounting system!
An electrician friend of mine told me that he has actually encountered fans that were mounted to a “cut-in” box mounted in gypsum board! Only slightly better (but still totally inadequate!) is a single-gang octagon box nailed or screwed to the side of a joist, and the fan attached to that.
While these can work, the risk is too high for you, the fan, and everything else in the way when the fan lets loose and falls!
The right way to install the fan is with boxes that are rated for ceiling fan use and installed with fasteners also rated for the job. This is true both for new and remodel installations.
Even the screws you mount the fan to the box must be a heavier gauge. Most fasteners for light fixtures are #8, but you should use #10 fasteners for fans - and boxes rated for fans will have #10 mounting holes right in them.
Here are some links that you can visit to get more information or purchase these boxes and hardware:
There are essentially two types of fan installation boxes: joist direct mount boxes, and boxes affixed to hardware that allows for fan placement between ceiling joists.
Direct-mount boxes affix alongside a ceiling joist or are mounted on a ladder block between two joists. Be sure to use pan head screws, with flat undersides of the screw heads, to attach these types of boxes. Some types have heavy-duty mounting flanges on the sides, others you directly screw the box to the ladder block, and others have a half-box that goes alongside the joist, with the round portion of the box extending ½” (12 mm) down, the same as the thickness of commonly used sheetrock.
Hardware-mounted fan boxes are available for new and remodel construction. Both utilize a crossbar with brackets that “bite” into the joists on both sides. The box can be tightened anywhere along the bar so that you place the fan in other places than alongside the joists. When installed correctly, the box will be suspended ½” (12 mm) below the bottom edge of the joists so that is flush with the ceiling sheetrock.
The remodel type allows you to insert the bar and box through a 4” (10 cm) round hole, and twist the threaded bar to have the toothed ends embedded in the joists. The box is then wired as normal, and the fan is mounted using #10 screws.
It really pays to do this correctly, and it’s not that expensive for the safety and peace of mind you’ll get.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
You know when it comes time to mount a ceiling fan box
in your home, it's gotta be done right and securely.
Fortunately, there's some great hardware
and techniques out there that'll help you
accomplish that task.
Stay tuned.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
If you're like us, you really enjoy
having those ceiling fans.
They really help keep the air moving around in the home,
make the home feel cooler, or when they're reversed,
you can actually, in the winter,
mix up the air a little bit better
so you don't have so much stratification
of warm air at the top of the room and cold at the bottom.
So they're great devices, but they depend,
pun intended, heavily on the right mounting hardware,
the right box in the ceiling.
We're gonna walk you through some of the hardware
that's available and using this mock-up.
Now, if you look at this mock-up,
please, you gotta go along with me
and suspend reality just a little bit.
It's like the world's upside down.
We're looking at the bottom side of your ceiling
where there's either what's called a joist,
a rafter, or a truss bottom cord
that is right above the sheetrock.
So we're looking at the underside
or up towards the sky here,
and this side is towards the room,
so the world's upside down here.
But this allows us to see everything clearly.
So when a place is being constructed,
and we'll show you in a moment
how to work with existing construction also,
you're wanting to mount some kind of box like this
that is rated for ceiling-found weight and vibration
and that sort of thing.
Well, how do you mount that on there?
If you mount this on top of that,
it's gonna stick way too far out of the ceiling
where the sheetrock is.
So there's different ways to accomplish that.
The first way is to put blocking between these rafters.
Now, this is a 16-inch or about a 41-centimeter
on-center rafter.
If it was 24 inches,
then we'd use a larger ladder block here.
The problem is if I just mount it like this
and then put this here,
it's not going to be proud enough
that when the drywall is put in beside it
that this is at the right,
it's not flush to the ceiling surface.
So what you would do is raise this
to where it's approximately, oh, about an inch.
And so what I do is I just put a couple blocks under here
just for demonstration purposes.
And these are about 12-millimeter, half-inch blocks.
So that gives us about 24 millimeters there.
Now you can see when that box is put here,
it's about the right height for that half-inch
or 12-millimeter drywall to be put in here.
That allows you to place this back and forth
where you need it.
And by moving the block up and down,
now you can put this exactly where you need it,
where you desire to be in the room.
Now, there's a real temptation.
Just take some sheetrock screws
and screw this to the block and then call it good.
But sheetrock screws are hardened.
They're a little bit brittle.
I would use panhead screws
that have a flat bottom to the head
that really bear well to the back of the box
and secure it exactly where it needs to be.
We'll come back and look at the box a little bit more
here in a few minutes.
Now, there's another device that's out here,
and this is what's called a pancake box
because it's so thin here.
And the space to do the wiring and to run in the wire
and the power supply is here.
And if your joist rafter or truss bottom cord
happens to be in the position
where you want your ceiling fan,
these simply get mounted on the side like that.
And again, secured with screws
that have flat under bottoms of the head
to really get this where it needs to be.
So you can move this up and down
and place it where it needs to be.
So that's another approach.
The third approach is to use one of these type of devices.
Now, these happen to be from Home Depot.
You can get them from other major hardware chains.
You can go on Amazon.
And if you look in the description below,
I actually have the links where you can download these,
but let's take a look and see what's included in the box.
So what you have is this same box.
It's the same exact box,
but it's got some mounting hardware.
And what you're going to do here
is these spread back and forth,
and you would simply place this where you want it,
affix it over here.
We would take the spacers off and all that,
and you're going to drive screws into it.
And now this can be slid back and forth
by untightening in that.
And we'll show you that real quick.
Okay, let's go ahead and set this up
as though we're going to install it.
Now, this cover on the top is not a functional cover.
It's simply to protect the box
while draw wall, mudding, paintings all being done.
And it's just thin sheet metal,
but let's go ahead and untighten this, remove it.
And then what you'll find inside
is what you're supplied with is a little instruction sheet,
the hardware to mount on the side here,
and the Romex or the cord connector
so that when you put the power supply
through one of the knockouts,
that's all secured properly.
Okay, now the other thing you're going to see
is that there are two nuts right here,
and those nuts are what hold the bracket on the back.
So you just take a nut driver,
untighten those slightly.
Now you can move this left and right
and place it where you want.
So let's suppose the position you want is right there.
Now, once that's there,
you would just tighten the nuts again
and you're ready to go.
Now, the other thing you need to be very careful of
is to use the right size nuts or excuse me,
the screws here to hold the weight of the fan.
So they're number 10,
and you can use number eight for light fixtures.
And how that's accomplished is, let me show you.
Notice this little piece right there slides back and forth.
There's a number eight, there's a number 10.
Number 10s are used to do the ceiling fan,
which we're talking about.
All right, so now you know how this is done
for new construction.
Three approaches, direct mount on a louder block,
a side saddle that goes just like this
on the joist rafter or truss bottom cord,
or this kind of device.
What about if the work is already done
and you're trying to retrofit and put a box in?
Fortunately, there's a device for that as well.
This kind of hardware is what you're going to be using.
This allows you, after a little bit of disassembly,
to reach up through the hole, spread this apart.
So we're going to put it to work here.
Now, one thing that I want to call out on this
is the weight ratings of this kind of hardware,
whether it's new or it is one of these remodels.
If you are using the 24-inch spacing right here,
which is about 61 millimeters,
you're going to be able to use up to 50 pounds,
which is about 23 kilograms.
If you're using the narrower spacing,
like this model is that we have here,
16 inches wide or 41 centimeters,
or millimeters, excuse me,
then what you've got is about 150 pounds or 68 kilograms
is the maximum amount of weight
that you're able to put onto these.
Now, in this particular case, when you open the box,
what you're going to get is this box mounted,
which is just like the other ones we showed,
but there is no courtesy cover
simply because you're doing a remodel.
You're not doing new construction
where there's drywall mud and paint and all that.
So there's no cover.
There is the cable connector right here.
There's a set of instructions and this set of hardware,
again, with the number 10 screws
that you're going to use to mount ceiling fans with.
Now, first thing we're going to need to do
to get this to work is to pull this box and bracket off.
And we're just going to use a 3-8 nut driver,
which is about a nine millimeter to remove this off
and a Phillips drive to take those screws off.
So let's get that removed.
You can see they take this mounting very seriously.
There's four connectors that hold this bracket.
Go ahead and remove the bracket.
And now this is set aside, of course.
Now, what we've done is reversed our model here
and made this the backside.
So you see what happens here.
Once this bar has all the other hardware removed,
now it's time to insert it through the hole.
So you would be underneath here
and you would simply take this, reach up through the hole
and let it set inside the cavity inside.
So what you're seeing up here, which is upside down,
and this model is only screwed together with sheet rock.
So I'm not going to be able to pressure it completely.
You're going to just start turning this.
And as you do here, I'm going to spin it around
so you can see there's the screw there.
So as I thread this out, then you can see this lengthen
and this will work all the way up to,
as we said, that 24 or 61 millimeter spacing.
But here we go.
We're just going to go ahead and screw this open.
All right, now at this point,
you're going to see that this has teeth on both sides.
There's two things you need to be aware of.
One, you need to hand tighten this.
Do not use a wrench,
but you want to make sure those teeth
completely indent and grip.
I won't be able to do that simply
because it'll blow out the sheet rock screws right here,
but you would tighten this by hand.
The second thing is you need to make sure
that these feet are oriented exactly like this.
They're sitting like a tripod.
And the reason for that,
that's going to put the height of this bar
exactly where it needs to be so that when you mount the box,
it is flush with the outside over here of the drywall.
When it's centered like this,
again, I can't work from this side
unless I was up in the attic.
What I'm going to do now is I'm taking this bracket.
And what I would do is put it up through the hole
and put it on the side.
If you try to put it up over the top, it's really hard,
but if you put it on the side and then do one more rotation,
you know, you can get it where you need it to be.
So now it's there.
And now I can take this box along with the hardware
and remount it in here.
Okay, now the box is pushed up tight against this,
as you can see here.
Now it's time to install the hardware again.
All right, so now the box has been pushed up
from underneath.
Of course, you would have the knockout in here
and have the cable securement device,
the cable Romex connector right here
so wire doesn't pull out.
There's a grounding screw as well.
Of course, use the number 10 screws to suspend a fan.
And there, this is ready to go
after you put all the hardware back in.
It'll never come down.
It'll support the fan securely.
I have an electrician friend that told me
he once went to work on the ceiling fan
and found that the homeowner had simply mounted
a clamp on box suspended only by drywall
and couldn't figure out why it was sagging
and why the whole thing was vibrating.
Don't be that guy.
This is the great way to do it.
We've shown you three or four great ways to secure...
Don't be that guy.
Use one of these great approaches
to make sure you put in a safe and secure mounting system.
Here's something else you might be interested in.
When it comes time to cut a hole in the ceiling,
anywhere from two to seven inches,
check out this tool that we reviewed,
Milwaukee's adjustable hole cutter with a debris shield
so the stuff doesn't fall on your face.
And while you're at it,
also check out this other video that YouTube
and we think is perfect for you.
Until the next time,
this is Dirt Farmer Jay from DirtFarmerJay.com.