If your bandsaw has a blade tension adjustment knob on the top of the saw, it can be inconvenient or downright uncomfortable to use. We found a great crank handle that is made for 14” (36 cm) bandsaws, but could be easily adapted to our Grizzly® 16” (41 cm) - what a difference!
If the stock blade tension knob that came with your bandsaw isn’t easy to reach or is difficult to turn, chances are you’ll avoid using it. That means that you’ll likely leave your saw fully tensioned when you are done with the saw for the day. That’s not good for the blade, saw, or tires.
Our first course of action was to see if there was a speed-adjust lever or another quick device to solve the issue with our 16” (41 cm) Grizzly® bandsaw. Nope. There are units for all the popular 14” saws - but nothing for our sized saw.
We then took a look to see if there were better handles that gave better leverage when tensioning the saw’s blade, as well as speed, both when tensioning and de-tensioning. Again, nothing we could see.
But, what if we could adapt something that was made for other saws? That’s when we took a look at the BigHorn® 14330 Bandsaw Tension Crank for 14” (36 cm) saws. We’re pleased to say that the handle fits our saw and required only minimal alterations to have it work beautifully:
Remove a couple of the nuts that came with the handle Remove the handle by loosening the handle’s set screw Shorten the shaft about 2” (50mm) Grind a flat spot on one side of the handle end of the shaft to allow the handle’s set screw to securely grip the handle and resist spinning Reinstall the handle at the desired height above the top of the case
After this, we simply removed the stock “star” knob and shaft after loosening the shaft’s combination position/compression set nut, washer, compression spring, and bottom washer. These were simply utilized in the same order when the BigHorn® handle was installed.
The specifications of the handle are: Thread: 3/8-16 tpi Shaft Thickness: 3/8" / 9.5mm Shaft Length: 13” / 33cm
You wouldn’t think that ⅜”-16 tpi thread would fit into a saw that was made in Taiwan - but it does.
To see where you can buy the BigHorn 14330 Band Saw Tension Crank, visit:
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
I love this bandsaw.
It's a hard worker and it's probably one of the most important tools.
I'd say it even competes with the table saw, but there's a feature on it that came from
the factory I couldn't stand, and that is this tension adjustment knob.
Hard to reach, hard on the wrist, very fatiguing.
I found a really good solution to that at a very economical price.
Stay tuned.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Having great tooling in the shop is a blessing.
You can do a lot of different things, and a bandsaw is such a hardworking tool.
But to properly use it, you have to tension the blade correctly, and then when you're
done with the work for the day, you need to take the tension off of the tool, otherwise
it's really hard on the tires, the framework, and the blade itself.
And that is done by this tension knob.
Now this is a 16-inch, it's not a 14-inch, so there's quick lever release type of systems
out there, but nothing available for this grizzly 16-inch.
But cranking this back and forth to take the tension off at the end, and then bringing
it back up, oh my word.
Very fatiguing, hard on the wrist, you're in a blind spot, you're kind of up on your
tippy toes, and I thought there's got to be a better way.
Well, there is.
Let me show you what I did.
All right, well let's open up the top cover here, and as you're aware, pretty standard
setup on a bandsaw, is that you have a lifter mechanism that makes this wheel travel up
or down, therefore increasing or decreasing tension on the blade that runs around it.
Well, as you can see here, you're cranking this up or down, takes a lot of turns to move,
and you're up, many times you have to get a stool and that sort of thing.
I thought there's got to be a better way.
Fortunately, there is.
I was able to find this crank system.
This is from Bighorn.
There is a link in the description below.
This is about a $30 investment, $35 investment.
With some very mild modification on this, you can get this to work absolutely beautifully.
So what I did is I took the Bighorn crank, which right now, when you take the handle
off, this shaft is 13 inches, 33 centimeters.
What you'll need to do is cut it down an inch and a half to 11 1⁄2 or 29 centimeters,
regrind a flat on it for a place for that Allen key or that Allen screw to bite in,
and now the crank will sit about the right level, not up too high, and now you can crank
it.
Well, let's get to work.
We'll go ahead and cut this down and reinstall it.
Let's begin by removing the old height adjuster knob here.
So I'm going to unscrew this and keep this from dropping, and as you can see, it takes
a lot of turns to get this to let go.
One eternity later.
All right, now the next thing we'll need to do is take this compression nut, which is
actually what provides the lift against the tension spring, and loosen that off and lift
this out.
All right, let's undo that.
There we go.
Unscrew this the rest of the way, lift it out, and as you do, hold on to the spring
and out comes that whole knob.
All right, let's get our modified Bighorn crank, and we'll install it in now instead.
All right, we now have our shortened Bighorn unit here with the flat that we've ground
into it.
We're going to go ahead and insert it back in the handle, bring the handle flush right
here, and let's go ahead and tighten it in.
Nice.
Okay.
All right, so we're now going to insert this through the top, and let's just start stacking
the items we're going to need on it.
One is that collar.
The second thing is one of the washers that go by the spring, that compress against the
spring.
The next is the spring itself, and the next is the next washer with the indent part towards
the spring.
And now we'll adjust this until it drops through the hole, through all that assembly, and down
in to the lift block.
Now we'll go ahead and crank this to get some depth on it until this is about the place
you want to be reaching to put it.
It's about right there.
Now we'll go ahead and tighten that lifter, that compression ring up here.
All right, let's go ahead and retighten this at the right position where the crank will
clear on the top, and that's the position the crank will stay above the top casing.
And really get that home tight, so you're going to have to come from a couple angles
because this is a tight space right here, because that's right behind the wheel.
There it is.
Okay, so now we're going to lift, and you can see this is not changing position because
of where we've locked that in.
So now we'll go ahead and re-tension it.
All right, with a simple modification, minimum expense, we've now replaced out this stock
tension handle with this crank, which is much more efficient and just a much more pleasure
to use.
So this also reduces the temptation of leaving the machine tensioned after you're done with
a work.
You can simply count the rotations back, like let's say five rotations back to where you
had it tensioned properly before.
And then when you come back to use the machine also, you can rotate it back around five and
then just double test the tension, make sure it's in the guides correctly.
Now a little technique that I use that may be handy to you to remember whether or not
I've got the machine tensioned or it's ready to use, is I use one of these welder magnets
right here.
If I put it in front of that, that means that I left the machine un-tensioned, and it's
not ready to use.
So before I'm going to use it, and right now you can see that is pretty doggone loose.
Before I'm going to tension it, I'm going to take this, put that up here, crank my whatever
it is.
In this case, it was about six cranks, seven cranks, and I'll test that back.
But this is a lot more efficient and is really going to help you maintain the machine much
more efficiently.
Here's another thing I know will interest you for your bandsaw, and that's putting these
urethane tires on it.
Check out this video where we show you how to install these tires without boiling them
in water, which actually can weaken them according to the manufacturer.
And you can put these on cleanly without a lot of hassle, and then check out this other
video also that YouTube and us think is perfect for you.
Hey, thanks for joining me today.
Until the next time, this is Dirt Farmer Jay from DirtFarmerJay.com.