How to Build the 'Rose on Gear' Kinetic Sculpture

Sculptures DIY
6 followers
5 Video Views·Feb 19, 2023
How to Build the 'Rose on Gear' Kinetic Sculpture
What's up everyone? Has it ever happened to you where you think that it's
Thursday and then you realize it's Friday?
And all you can really do is just put your hands up.
Put your hands up. Well that's what this piece is and I'm going to now show you
how you can make one yourself. I'm Jay, this is JBV Creative. Let's create.
Before we begin I just want to give a quick thanks to my sponsor for today's
video, DigitMakers.ca. They provided me with this D3D filament.
It's freaking awesome and it allows me to go through all the iterations
that is required to make these projects happen. So thank you DigitMakers.ca.
Let's get to the video. Okay let's do this. This is actually one of my
smallest builds that I've done so far. So this only takes 10 hours to print.
You can print the whole thing in one build and it's only about 120 grams of
filament. So like two bucks by my calculation.
So get pumped. Let's do this. This is going to be super quick.
So the first thing you're going to do, take your base, take the small bevel gear
and that's going to wedge into this hole in the side of the base.
You're then going to take your crank and this little knob.
Put the knob into the end of the crank and snap it on with a c-clamp.
Then take the crank that goes on the end of that bevel gear.
Just push it on and take the large c-clamp. There's three sizes. There's a
large, a medium, and a small. You need the biggest one.
That snaps onto the end. Boom. Make sure it spins.
Give it a few spins. Make sure it's rotating but it doesn't have to be
perfect. Let's move on to the next bit. So grab your, I think I call this an
oscillating wheel, and this hex shaft. The hex shaft goes
into the oscillating wheel from the front.
Now that goes into this hole closest to the bevel gear that you just put in.
You take the bigger bevel gear and that goes on the end of that shaft.
Now you grab your medium c-clamp and you clamp that into place.
So give that a few spins. Make sure everything's
spinning. Just keep in mind, if it's not perfect, the more that you rotate
everything it will start to work itself. Next thing we're going to do,
take your rack, rack attack, and with the knob facing
towards the front of the base, that slides into the slot here next to
the stand. Next grab your gear with slot thing.
Make sure the oscillating wheel is in the top position.
Now take your gear with the slot that goes into the last remaining hole
here on the coming out of the base. You have to line up the slot with the knob
on the wheel and the gear teeth with the rack. So the
thing to keep in mind here is, this is the lowest position that the
hands will be in. So it's going to be in the down position.
So you have to pick the location on the rack that you want it to be.
So I like to keep it kind of towards like maybe
here because that way when it goes up, I like it when the hands are super pumped
up. You know like kind of like this, not just like this,
not small pumped, big pumped, just like that.
Okay so we can c-clamp that into place. Make sure everything's moving again and
then we can keep going forward. So the next thing we're going to do,
take your two gear pieces. These gear pieces
go into the bottom holes in the stand on the base here.
So the key is to make sure that they're lined up in
equal and opposite positions. If you don't get them lined up in equal and
opposite positions now, you're gonna have to take it apart.
So just get it the first time. It's hard to get these c-clamps out.
C-clamp those in from the back. Sweet. So the next thing you're going to do is
take your top link with a slot on it.
That goes into the hole on the top here on the right
and the slot lines up with the hole on the gear rack.
C-clamp that into place from the back. C-clamp the gear rack into place.
Now you can do the other slot on the other side just like that.
Boom. Now you're going to take these arm hand links, I think I call them, and
those just slot into these holes just like this.
Get the other side and then the final touch. Take your hands,
make sure thumbs are in towards each other
and that just slides onto the top. Boom. That's it. Simple, easy,
fun. Let's show how pumped we are with a nice background and everything.
There it is. This is a fun one. It's got a little bit of everything. It's got
gears. It's got bevel gears. It's got these four bar linkages. It's got this
slot and oscillating hand thing. It's got a
little bit of everything and it's all in a package that is
easy to print, easy to put together. I am very pumped about how this one turned
out. I'd love to hear your thoughts. Let me
know in the comments below and otherwise I'll see you in the next
video.
